Search

The fuzziness and randomness are significant epistemic uncertainty within the qualitative categorization of the two critical factors, the frequency and severity, which are not fully considered in the traditional risk matrix. This paper mainly proposes a cloud risk matrix method for the risk assessment of process safety considering the epistemic uncertainty in expert elicitation. The cloud model is employed to provide a mathematical expression for the fuzziness and randomness in the linguistic variables by its two numerical characteristics entropy En and hyperentropy He . An adjusted Mamdani inference algorithm is constructed for the determination of an integrated risk cloud given the value of input variables. And the centroid method is improved to be adapted to the calculation of risk index from the enormous cloud droplets in the integrated risk cloud. A case study of risk assessment for distillation column unit is performed to illustrate the process of cloud risk matrix in detail, and the validity and rationality are verified by contrast to the results from the fuzzy risk matrix. Results indicate the proposed method can handle the randomness of qualitative concepts, which is more suitable to the practical condition. Moreover, the effect of the hyperentropy He on the randomness of risk index is also investigated and discussed for the reference to parameter selection. The proposed cloud risk matrix can provide an effective risk inference tool in a wide range of engineering fields.

Lung cancer is a common malignant neoplasm that is prone to distant metastasis. Gastrointestinal metastasis from lung cancer is rather rare no matter what stage. Herein, we presented a case of pulmonary adenocarcinoma six months after thoracoscopic Lobectomy isolated metastasis to sigmoid colon. Then the patient underwent radical resection of metastatic tumors of sigmoid colon. The pathologic morphology and immunohistochemistry of lung adenocarcinoma is highly consistent with the sigmoid colon tumor and their gene profiles are likely similar expect for an AXIN1 mutation in primary tumor and not in the metastatic lesion.

Wind energy, one of the most sustainable renewable energy sources, has been extensively developed worldwide. However, owing to the strong regional and seasonal differences, it is necessary to first evaluate wind energy resources in detail. In this study, the offshore wind characteristics and wind energy potential of Bohai Bay (38.7° N, 118.7° E), China, were statistically analyzed using two-year offshore wind data with a time interval of one second. Furthermore, Nakagami and Rician distributions were used for wind energy resource assessment. The results show that the main wind direction in Bohai Bay is from the east (−15°−45°), with a speed below 12 m/s, mainly ranging from 4 to 8 m/s. The main wind speed ranges in April and October are higher than those in August and December. The night wind speed is generally higher than that in the daytime. The Nakagami and Rician distributions performed reasonably in calculating the wind speed distributions and potential assessments. However, Nakagami distribution provided better wind resource assessment in this region. The wind potential assessment results suggest that Bohai Bay could be considered as a wind class I region, with east as the dominant wind direction.

In order to solve the problems of die and tooling manufacturing and assembling for the foil forming, especially for the foil micro forming, high-pressure water jet forming (HPWJF), a new die-less forming process for foil parts is proposed. In the forming process, liquid medium such as water and oil is utilized as a flexible tool to deform the ultrathin foil. In this paper, the computational fluid dynamics (CFD) software Fluent was used to simulate the water jet generation in the water jet nozzle and high-speed water impacting on a rigid surface. And then, the effects of jetting distance on the jetting pressure were obtained. To measure the precise mechanical parameters of copper foils, a digital speckle test method was used to detect the tensile process. Local bulging experiment was conducted for the copper foil with a thickness of 50 μm. When the inlet pressure is 8.5 MPa, the suitable jetting distance is 40 mm for the 50-μm-thick copper foil. In such conditions, the bulging height of the copper foil is 1.20 mm in the experiment. The fluid–solid coupled method by using Fluent and Abaqus was applied to simulate the deformation of the copper foil. The errors between the simulated results and the experimental values are lower than 10 %. Furthermore, both the experiment and simulation for micro stretching of 30-μm-thick copper foil were performed. The cylinder die with a diameter of 3 mm and a height of 1.5 mm is used to form the copper foil. Results show that the copper foil cracks when the jetting distance is 24 mm, and the inlet pressure is 12 MPa. With the increase of the inlet pressure, the drawing depth of the copper foil gradually increases, and the bottom of the cylinder part thins gradually, and the wrinkling of the flange of the cylinder part becomes more and more severe.

The thread and spline synchronous rolling process can form the external threaded and external splined tooth profiles on different parts of component by only one rolling process. However, it is a coupled rolling process where the thread rolling coupling with the spline rolling, and both phase adjusting requirements of dies before rolling for thread rolling and spline rolling should be satisfied in the synchronous rolling process. Thus, the phase adjustment only by rotating die may be difficult to ensure the thread and spline rolling by different dies well connects respectively. In this paper, requirements of phase difference adjustment for dies before thread rolling and before spline rolling have been studied systematically, and the mathematical expressions of phase difference adjustment have been established, and then the requirements of phase difference under different starts of threaded workpiece and die (or teeth of splined workpiece and die) for two and three rolling dies before thread rolling (or spline rolling) have been investigated. Based on these, the ratio S of phase difference between corresponding threaded sections of rolling dies to that between corresponding splined sections of rolling dies was introduced, and the phase characteristic between dies and the method of phase difference adjustment under different parameters in thread and spline synchronous rolling process were systematically researched. The results indicated that: (1) for thread (or spline) rolling process, if the remainder from dividing the starts nw of thread (or teeth Zw of spline) of workpiece by number N of rolling dies is equal to the remainder from dividing the starts nd of thread (or teeth Zd of spline) of rolling die by N, i.e., nw≡nd(mod N) (or Zw≡Zd(mod N)), then the phases of dies before rolling are the same, else there is a phase difference between dies; (2) for thread and spline synchronous rolling process, if the phase difference of splined section between rolling die j (j = 2,…, N) and rolling die 1 is \( {\varphi}_{{\mathrm{s}}_{j1}}=\frac{h}{N}{\theta}_s\left(h=1,\dots, N\right) \) and ratio of phase difference is \( {S}_{j1}=\frac{N}{h}k+1\left(k=0,1,2,3,\dots \right) \), then the die structures of two dies are the same, i.e., the relative phase between threaded and splined sections for two dies are the same, else the die structures of rolling dies j and 1 are different and the phase difference for threaded sections of rolling dies and the phase difference for splined sections of rolling dies are assured by die structure itself.