Search

Microwave-assisted ignition is an emerging high-performance ignition method with promising future applications in aerospace. In this work, based on a rectangular waveguide resonant cavity test bed, the effects of two parameters (material and diameter) of the microwave antenna on the ignition and combustion characteristics of ADN-based liquid propellant droplets were investigated using experimental methods. A high-speed camera was used to record the droplet combustion process in the combustion chamber, the effect of the microwave antenna on the propellant combustion response was analyzed based on the emission spectroscopy method, and finally, the loss of the microwave antenna was evaluated using a scanning electron microscope. The experimental results show that the droplet has the lowest critical ignition power (179 W) when the material of the microwave antenna is tungsten, but the ignition delay time is higher than that of copper. A finer diameter of microwave antenna is more favorable for plasma generation. At a microwave power of 260 W, the ignition delay time of the droplet with a microwave antenna diameter of 0.3 mm is 100 ms lower than that of 0.8 mm, which is about 37.5%. In addition, this study points out the mechanism of microwave discharge in the droplet combustion process. The metallic microwave antenna not only collects the electrons escaping from the gas discharge, but also generates a large amount of metallic vapor, which provides charged particles to the plasma. This study provides the possibility for the application of microwave-assisted liquid fuel ignition. [ABSTRACT FROM AUTHOR]

This study investigates the evaporation and ignition characteristics of a single droplet of ammonium dinitramide (ADN)-based liquid propellant utilizing a waveguide resonant cavity device, in conjunction with a high-speed photographic imaging system and testing system. Experimental methods are employed to analyze the impact of microwave pulse width and duty cycle on the puffing and meicro-explosion phenomena of the droplet, as well as the delay time and duration of ignition. The experimental findings reveal that increasing the duty cycle enhances the ignition success rate and diminishes flame development time. Specifically, elevating the microwave duty cycle from 60% to 80% reduces the ignition delay time of the droplet from 132.8 ms to 88.1 ms, and the ignition duration from 23.1 ms to 19.9 ms. Furthermore, an increase in microwave energy pulse width expedites the combustion process of the flame and influences plasma generation. Increasing the pulse width of microwave energy from 20 µs to 40 µs prolongs the ignition delay time from 140.3 ms to 200.5 ms and extends the ignition duration from 56.7 ms to 77.8 ms. Additionally, it is observed that a higher duty cycle leads to a more pronounced puffing phenomenon that initiates earlier. In contrast, a higher pulse width results in a more pronounced puffing phenomenon that commences later. This study provides a thorough investigation into the microwave ignition mechanism of ADN-based liquid propellants, offering theoretical insights into the ignition and combustion stability of such propellants in microwave-assisted ignition systems. [ABSTRACT FROM AUTHOR]

When the satellite is in orbit, the thruster will experience drastic temperature changes (100–1000 K) under solar radiation, which will affect the rarefied gas flow state in the micro-nozzle structure of the cold gas micro-thruster. In this study, the effect of different wall temperatures on the rarefied flow and heat transfer in the micro-nozzle is investigated based on the DSMC method. The micro-nozzle structure in this paper has a micro-channel with a large length-to-diameter ratio of 10 and a micro-scale needle valve displacement (maximum needle valve displacement up to 4 μm). This leads to more pronounced multiscale flow characteristics in the micro-nozzle, which is more influenced by the change in wall temperature. At wall temperatures ranging from 100 K to 1000 K, the spatial distribution of local Kn distribution, slip velocity distribution, temperature, and wall heat flux distribution in the micro-nozzle were calculated. The slip flow region is located in the flow channel and transforms into transition flow as the slip velocity reaches approximately 50 m/s. The spatial distribution of the flow pattern is dominated by the wall temperature at small needle valve opening ratios. The higher the wall temperature, the smaller the temperature drop ratio in the low-temperature region inside the micro-nozzle. The results of the study provide a reference for the design of temperature control of micro-nozzles in cold gas micro-thrusters. [ABSTRACT FROM AUTHOR]

As a new type of energy-containing material, Ammonium dinitramide based liquid propellant has the advantages of being green, having low toxicity, good stability, and high safety performance. Traditional catalytic combustion methods require preheating of the catalytic bed and deactivation of the catalytic particles at high temperatures, while microwave ignition methods can effectively solve these problems. To study the combustion characteristics of ADN-based liquid propellants during microwave ignition, the influence of microwave power and gas flow rates on the combustion process are analyzed using experimental methods. A high-speed camera was used to observe the enhanced effects of microwave power and gas flow on plasma and flame. Combined with temperature measurement, the combustion process of ADN-based liquid propellants under the action of plasma was analyzed. The combustion process in the presence of microwaves was observed by comparing parameters such as flame length, flame temperature, and radical intensity. Those results show that, with the increase in microwave power, the luminous burning area of the flame grows significantly. The microwave power is increased by 250 W each, and the flame jet length is increased by nearly 20%. The increase in microwave power also leads to an increase in propellant combustion temperature, however, this increase gradually slows down. At a gas flow rate of 20 L/min, the ADN-based liquid propellant showed the best combustion performance with a maximum jet length of 14.51 cm and an average jet length increase of approximately 85.9% compared to 14 L/min. Too much gas flow rate will hinder the development of the jet, while the high-velocity airflow will have a cooling effect on the flame temperature. The results provide a basis for the specific parameter design of microwave ignition and promote the application of ADN-based liquid propellants in the aerospace field. [ABSTRACT FROM AUTHOR]