Search

A novel wideband multilayer dual‐podal Vivaldi antenna with broadband characteristics from 5.5 to 20.82 GHz, is presented. Contrary to traditional Vivaldi antennas that are antipodal‐based, this design is realised by placing a pair of podal Vivaldi antennas with corrugated slots on the top and bottom of a substrate stack (consisting of two dielectric layers) using a Bondply. The pair is fed in‐phase with the help of a Strip‐Line (SL) transmission section that is terminated on a radial stub to couple capacitively to the antenna elements. With this technique of electrically coupling a podal Vivaldi pair, improved performance parameters are achieved, specifically: a measured maximum gain of 9.33 dBi, Half Power Beam Width of 126.5° in the H‐plane, and a maximum Front‐to‐Back (F/B) ratio of 14.36 dB with an overall antenna size of 29 × 21 × 1.63 mm. The in‐depth understanding of the working mechanism is supported by a detailed parametric analysis, current distribution, and a clear physical insight into the operating principles. Moreover, a 1 × 4 Vivaldi antenna array is also designed and analysed. A measured maximum gain of the 13 dBi at 15 GHz in the array is achieved along with the wide bandwidth of 6.3 GHz from 10.78 to 17.07 GHz. The array is fed through an SL corporate feed network that ensures in‐phase excitation of all four Vivaldi pairs. A Grounded Co‐planar Waveguide to SL transition is adopted for connecting the 2.92 mm Radio Frequency launcher on the top layer. The very compact geometry of the proposed structure enables its integration into the systems for remote sensing applications. [ABSTRACT FROM AUTHOR]

A novel dynamically reconfigurable bandpass filter (BPF) employing stepped-impedance resonators (SIRs) that can operate as either a single-band or a dual-band filter is demonstrated. The reconfigurable BPF uses four positive-intrinsic-negative (p-i-n) diodes as switching elements. With the four p-i-n diodes in the “OFF” state, the filter behaves as a low-loss (0.85 dB) single-band BPF with a passband around 2.45 GHz. The reconfigurable SIR filter can operate as a dual-band BPF with two center frequencies at 1.6 and 2.45 GHz. The diodes are dynamically set to the “ON” state in the presence of a 1.6-GHz RF signal that is received by an RF triggered power management unit (PMU), integrated on the back side of the microstrip filter in a dual-layer architecture. The RF triggered PMU consists of a planar inverted-F antenna, a high-efficiency voltage doubler rectifier (47% at −13 dBm) and an active dc-to-dc power booster. The rectified output voltage is used as the enabling voltage for the dc-to-dc power booster. This, in turn, provides the required dc power for the diodes biasing. The filter switches from single-band to dual-band when a wireless input RF signal (> −13 dBm) is received by the RF triggered PMU antenna. [ABSTRACT FROM AUTHOR]

The use of a tunable power splitter (PS) as a constituent component of a simultaneous wireless information and power transfer (SWIPT) system is discussed. Two varactor diodes are used to achieve a tunable output power ratio P2 : P3 varying from 1 : 1 to 1 : 10 under good matching conditions. The SWIPT system that operates at 2.4 GHz consists of a typical patch antenna, cascaded with the tunable PS, and a voltage doubler rectifier. The constituent components were implemented and tested as stand-alone devices and were subsequently combined in a measurement system using interconnectors. The effect of the tunable PS was explored with respect to the SNR measurements on the port that is intended for the information decoding receiver and the DC voltage measurements on the termination load of the rectifier that is connected directly on the energy harvesting port of the tunable PS. A spectrum analyzer is used for the SNR measurements while the input power is controlled using a signal generator. Both wireless power transmission and on-board measurements verify that the harvested energy can be maximized by using the minimum SNR at the information decoding branch at the expense of DC power consumption required for the biasing of the varactor diodes. [ABSTRACT FROM AUTHOR]

An overview of design requirements and novel approaches for improved performance UHF radio frequency identification (RFID) tags is presented. Two matching techniques, an inductively coupled structure and a serial stub structure are discussed. Different miniaturized antenna topologies are proposed, focusing on low-profile, high efficiency and high directivity in very compact (less than 3 in x 3 in) configurations. [ABSTRACT FROM AUTHOR]

Two CPW-fed elliptical monopoles were fabricated on liquid crystal polymer (LCP) with reconfigurable rejection band (band-notch) characteristics in the frequency range between S and 6 GHz. The first antenna uses a λ/2 long, U-shaped slot and the second antenna uses two symmetrically placed λ/4 long, inverted L-shaped stubs as resonating elements. Microelectromechanical system (MEMS) switches are used to activate and deactivate the resonating elements without the need of dc bias lines due to a novel design of the switch geometry. Transmission line models and surface current distributions are used to explain the effect of the added resonating elements. Reflection coefficient radiation pattern and gain measurements are presented to verify the design concepts featuring a very satisfactory performance. [ABSTRACT FROM AUTHOR]

A single-feed circular microstrip antenna with reconfigurable polarization capability is proposed. This antenna has a simple structure, which consists of a radiating circular patch, five switches (PIN diode), three matching stubs, and a 50 Ω) microstrip feed line. It can be switched between 4 different states: two states (low-frequency and high-frequency) for linear polarization (LP), one state for left hand circular polarization (LHCP) and one for right hand circular polarization (RHCP) by controlling the bias voltage of two PIN diodes. At the same time, three switchable matching stubs are used for matching every polarization state. Simulation results and experimental results show that the pro- posed antenna demonstrates a low cross polarization level, good impedance bandwidth, and a very good axial ratio in the circularly polarized states. [ABSTRACT FROM AUTHOR]

This paper presents the use of pin diodes to reconfigure the impedance match and modify the radiation pattern of an annular slot antenna (ASA). The planar antenna is fabricated on one side of a Duroid substrate and the microstrip feeding line with the matching network is fabricated on the opposite side of the board. The central frequency is 5.8 GHz and, by reconfiguring the matching circuit, the antenna was also designed to operate at 5.2 and 6.4 GHz. Pin diodes are also used to short the ASA in preselected positions along the circumference, thereby changing the direction of the in the plane defined by the circular slot changes. As a proof of concept, two pin diodes are placed 45° on both sides of the feeding line along the ASA and the direction of the is shown to align with the direction defined by the circular slot center and the diode. Consequently, a design that is reconfigurable in both frequency and radiation pattern is accomplished. Return loss and radiation pattern measurements and simulations are presented, which are in very good agreement. [ABSTRACT FROM PUBLISHER]