Search

Abstract: One of the major barriers that hinder the application of forward osmosis (FO) processes is the lack of optimized membranes that possess high water flux, low salt leakage and good anti-internal concentration polarization (ICP) and anti-fouling/anti-scaling properties during practical FO operations. In this study, novel composite FO hollow fiber membranes with an RO-like selective skin and an NF-like secondary selective skin were successfully developed for the first time. The fabrication procedures involved making ultrafiltration hollow fiber substrate using poly(amide–imide) (PAI) polymer material via phase inversion method, followed by interfacial polymerization (IP) and chemical modification to yield a polyamide RO-like inner skin and a positively charged NF-like outer skin, respectively. It was found that the sequence of conducting IP on the substrate inner surface prior to the chemical modification of the outer skin was preferred in order to achieve better performance for the resultant double-skinned hollow fibers. The newly developed FO hollow fibers exhibited high water permeability of 2.05L/m2 hbar and 85% rejection to NaCl at 1bar pressure as well as superior FO water flux of 41.3L/m2 h and low ratio of salt flux over water flux of 0.126g/L when using DI water and 2.0M NaCl as feed and draw solutions, respectively, in the active layer facing draw solution (AL-DS) orientation. Furthermore, the experimental results showed that the composite FO hollow fiber membrane was able to outperform single-skinned membrane when the feed contains divalent ions or the feed exhibits high scaling tendency to membrane. This suggested that the integration of RO- and NF-like two selective skins in FO membrane is an effective way to minimize the ICP effect, mitigate the membrane scaling and thus enhance the feasibility of FO processes for practical applications. [Copyright &y& Elsevier]

Abstract: For the first time, a specially designed pressure retarded osmosis (PRO) hollow fiber membrane has been successfully developed and applied in the PRO process to demonstrate its potential for power generation. The membrane fabrication method is similar to that used for making thin-film composite (TFC) forward osmosis hollow fiber membranes, but further optimization and improvement have led to a new type of TFC hollow fiber membranes with much greater mechanical strength in addition to its excellent separation property and high water flux. The TFC PRO hollow fiber membranes have a water permeability (A) of 9.22×10−12 m/(sPa), salt permeability (B) of 3.86×10−8 m/s and structural parameter (S) of 4.6×10−4 m. It can withstand hydrostatic pressure as high as 9bar with its relatively large dimension of 0.98mm lumen diameter. This PRO hollow fiber membrane is superior to all other PRO membranes reported in the open literature in terms of power density. A power density as high as 10.6W/m2 can be achieved using seawater brine (1.0M NaCl) and wastewater brine (40mM NaCl), which suggests that the newly developed PRO hollow fiber membrane has great potential to be applied in PRO processes to harvest salinity gradient energy. A higher pressure is preferred as it allows generation of higher power density (pressures of 12bar may be optimal for seawater as the high salinity stream), and this can be realized by reduced fiber dimension. Further optimization of the membrane structure will be performed. [Copyright &y& Elsevier]

Abstract: Forward osmosis (FO) has received intensive studies recently for a range of potential applications such as wastewater treatment, water purification and seawater desalination. One of the major challenges to be overcome is the lack of an optimized FO membrane that can produce a high water flux comparable to commercial RO membranes. Two types of thin-film composite FO hollow fibers with an ultra-thin polyamide-based RO-like skin layer (300–600nm) on either the outer surface (#A-FO) or inner surface (#B-FO) of a porous hollow fiber substrate have been successfully fabricated. These novel composite FO hollow fibers have been characterized by a series of standard protocols and benchmarked against commercially available FO flat sheet membranes and reported NF hollow fibers used for the FO process. The characterization reveals that the FO hollow fiber membranes possess a large lumen. The substrates are highly porous with a narrow pore size distribution. The active layers present excellent intrinsic separation properties with a hydrophilic rejection layer and good mechanical strength. The #B-FO hollow fiber membrane can achieve a high FO water flux of 32.2L/m2 h using a 0.5M NaCl draw solution in the active rejection layer facing draw solution (AL-facing-DS) configuration at 23°C. The corresponding salt flux is only 3.7g/m2 h. To the best of our knowledge, the performance of the #B-FO hollow fiber is superior to all FO membranes reported in the open literature. The current study suggests that the optimal FO membrane structure would possess a very small portion of sponge-like layer in a thin and highly porous substrate, which suggests a way for further improvement. [Copyright &y& Elsevier]