Search

The fabrication of new membrane that is able to produce stable high power density is essential for the development of pressure retarded osmosis (PRO) technology. In this work, thin film composite (TFC) polyetherimide membranes with three different substrate structures were fabricated and characterized. The PRO performance of the resultant membrane was evaluated through two pressure cycle experiments and stability tests. The primary objective of this work is to systematically study PRO membrane’s mechanical stability and mass transfer properties under high operating pressures, which determine the power density of the membrane in the PRO process. Experiments revealed that water permeability ( A p ) and salt permeability ( B p ) under different pressures varied. The A p and B p are better indicators for examining the variation of PRO membrane structure under pressure. Within the operating pressure range of 17.2 bar, the top polyamide layer of TFC PEI-2# membrane mainly experienced a reversible deformation. In the two pressure cycle tests, the water flux, specific salt flux and power density obtained in the upward and downward measurements in each cycle are close to each other. The first cycle and the second cycle also show excellent reproducibility. The membrane was able to maintain almost unchanged water flux and power density of 12.8 W/m 2 at 17.2 bar over the 10 h testing time, suggesting the membrane’s great potential to be used in practical application in the future. [ABSTRACT FROM AUTHOR]

Abstract: Pressure retarded osmosis (PRO) is a promising membrane process to harvest the vast amount of free energy from the mixing of fresh and salty waters without adverse environmental impacts. A competent membrane for PRO should possess the features of high water permeability to allow water permeation, excellent salt rejection to maintain the osmotic driving force, low structure parameter to minimize the internal concentration polarization (ICP), and robust strength to withstand the required hydraulic pressure. In this work, we have developed a novel hollow fiber membrane by balancing these competing factors based on our prior experience in the thin-film composite (TFC) membranes. The newly developed TFC hollow fiber membrane can achieve a power density of 20.9W/m2 at a pressure of 15bar, using synthetic seawater brine (1.0M NaCl) as the draw solution and synthetic river water (1mM NaCl) as the feed water, respectively. The simultaneous specific reverse salt flux was found to be 0.03mol/L, which is much lower than reported flat-sheet membranes, as the self-supported hollow fiber membrane can eliminate the deformation-enhanced reverse salt diffusion that is typical for flat-sheet membranes. However it was observed that the water permeability and structure parameter of the TFC hollow fiber membrane varied noticeably corresponding to the change in the hydraulic pressure imposed in the fiber lumen. Over a certain range (ΔP<15bar), such variations of increasing A value and decreasing S value proved to have positive impacts, as they facilitate the water permeation and reduce the ICP in the PRO process. [Copyright &y& Elsevier]

Abstract: For the first time, a specially designed pressure retarded osmosis (PRO) hollow fiber membrane has been successfully developed and applied in the PRO process to demonstrate its potential for power generation. The membrane fabrication method is similar to that used for making thin-film composite (TFC) forward osmosis hollow fiber membranes, but further optimization and improvement have led to a new type of TFC hollow fiber membranes with much greater mechanical strength in addition to its excellent separation property and high water flux. The TFC PRO hollow fiber membranes have a water permeability (A) of 9.22×10−12 m/(sPa), salt permeability (B) of 3.86×10−8 m/s and structural parameter (S) of 4.6×10−4 m. It can withstand hydrostatic pressure as high as 9bar with its relatively large dimension of 0.98mm lumen diameter. This PRO hollow fiber membrane is superior to all other PRO membranes reported in the open literature in terms of power density. A power density as high as 10.6W/m2 can be achieved using seawater brine (1.0M NaCl) and wastewater brine (40mM NaCl), which suggests that the newly developed PRO hollow fiber membrane has great potential to be applied in PRO processes to harvest salinity gradient energy. A higher pressure is preferred as it allows generation of higher power density (pressures of 12bar may be optimal for seawater as the high salinity stream), and this can be realized by reduced fiber dimension. Further optimization of the membrane structure will be performed. [Copyright &y& Elsevier]