Search

Due to the pulsating power at the inverter output terminals, the passive storage elements of the boost stage of the current-fed switched inverter (CFSI) contain a power frequency harmonic component (100 Hz), apart from dc and switching frequency components. In prior designs, the second harmonic component is suppressed by increasing the size of the input filter inductor and capacitor or by using additional circuits. This paper presents a complete characterization of a control-based approach to suppress the power frequency harmonic component in the input inductor current of a CFSI. It also presents a comprehensive characterization of the harmonic power redistribution. Using the proposed approach, it is demonstrated that the inductor value of a CFSI is reduced by 61% for the same peak-to-peak ripple. This leads to an improvement in the conversion ratio, efficiency, and power density of the overall converter. A SiC MOSFET-based CFSI with 75-kHz switching frequency is used to verify the proposed design philosophy. [ABSTRACT FROM AUTHOR]

Buck-converter-based topologies are used to generate high-frequency sinusoidal outputs. Buck-based inversion circuits such as voltage source inverters or class-D amplifiers have inherent control-to-output linearity in large-signal sense. However, in these topologies, the instantaneous output is always smaller than the dc-input during linear modulation. A differential boost inverter (DBI) is a boost-based topology that is used to generate a sinusoidal output. In DBI, the instantaneous output can be higher or lower than the dc-input voltage. DBI exhibits nonlinear control-to-output behavior in large-signal dynamic sense. Therefore, generating a high-frequency sinusoidal output using this topology is a challenge. The issues associated with a DBI for high-frequency sine wave generation are characterized in this paper. Conventional linear and nonlinear control techniques fail to produce a high-quality sine wave output at higher operating frequency. A nonlinear feedback linearization technique is proposed, which forces the output to be linear with respect to the reference even at higher operating frequency. This leads to a high-frequency high-quality sine wave generation using a DBI. The proposed modulator is verified using a laboratory prototype to generate a sine wave up to 2 kHz. A triangular wave of 100-Hz frequency is also generated by the proposed technique. Superior dynamic responses of a dynamic linearizing modulator controlled DBI for a step change in frequency, load current, input voltage, and reference are also experimentally verified. [ABSTRACT FROM AUTHOR]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

Switched boost inverter (SBI) is a single-stage power converter derived from Inverse Watkins Johnson topology. Unlike the traditional buck-type voltage source inverter (VSI), the SBI can produce an ac output voltage that is either greater or less than the available dc input voltage. Also, the SBI exhibits better electromagnetic interference noise immunity when compared to the VSI, which enables compact design of the power converter. Another advantage of SBI is that it can supply both dc and ac loads simultaneously from a single dc input. These features make the SBI suitable for dc nanogrid applications. In this paper, the SBI is proposed as a power electronic interface in dc nanogrid. The structure and advantages of the proposed SBI-based nanogrid are discussed in detail. This paper also presents a dq synchronous-reference-frame-based controller for SBI, which regulates both dc and ac bus voltages of the nanogrid to their respective reference values under steady state as well as under dynamic load variation in the nanogrid. The control system of SBI has been experimentally validated using a 0.5-kW laboratory prototype of the SBI supplying both dc and ac loads simultaneously, and the relevant experimental results are given in this paper. The low cross regulation and the dynamic performance of the control system have also been verified experimentally for a 20% step change in either dc or ac load of SBI. These experimental results confirm the suitability of the SBI and its closed-loop control strategy for dc nanogrid applications. [ABSTRACT FROM AUTHOR]

The flying capacitor multicell inverter (FCMI) possesses natural balancing property. With the phase-shifted carrier-based scheme, natural balancing can be achieved in a straightforward manner. However, to achieve natural balancing with the harmonically optimal phase-disposition (PD) carrier-based scheme, the conventional approaches require (n − 1) × (n − 1) trapezoidal carrier signals for an n-level inverter, which is ( n − 1) × (n − 2) times more than that in the standard PD scheme. This paper proposes two improved natural balancing strategies for FCMI under PD scheme, which use the same (n − 1) carrier signals as used in the standard PD scheme. In the first scheme, the on-line detections are performed of (i) the band in which the modulation signal is located, (ii) corresponding period number of the carrier, and (iii) rising or falling half cycle of the carrier waveform to generate the switching signals based on certain rules. In the second strategy, the output voltage level selection is first processed and the switching signals are then generated according to a rule based on preferential cell selection algorithm. These methods are easy to use and can be simply implemented as compared to the other available methods. Simulation and experimental results are presented for a five-level inverter to verify these proposed schemes. [ABSTRACT FROM AUTHOR]

The hysteresis modulation for power electronic converters is attractive in many different applications because of its unmatched dynamic response and wide command-tracking bandwidth. Its application and benefits for two-level converters are well understood, but the extension of this strategy to multilevel converters is still under development. This paper summarizes and reviews the various hysteresis modulation approaches available in the literature for multilevel converters. The pros and cons of various techniques are described and compared for tracking the reference signal in order to attain an adequate switching optimization, excellent dynamic responses and high accuracy in steady-state operation. By using the recently developed multilevel hysteresis modulation approaches, the advantages of using several accessible dc potentials in a multilevel inverter have been fully exploited. All of these hysteresis modulation approaches are tested for tracking a current reference when applied to a five-level inverter. The relevant simulation and experimental results are also presented. This study will provide a useful framework and point of reference for the future development of hysteresis modulation for multilevel converters. [ABSTRACT FROM AUTHOR]

In this paper, the performance of voltage-source converter-based shunt and series compensators used for load voltage control in electrical power distribution systems has been analyzed and compared, when a nonlinear load is connected across the load bus. The comparison has been made based on the closed-loop frequency response characteristics of the compensated distribution system. A distribution static compensator (DSTATCOM) as a shunt device and a dynamic voltage restorer (DVR) as a series device are considered in the voltage-control mode for the comparison. The power-quality problems which these compensator address include voltage sags/swells, load voltage harmonic distortions, and unbalancing. The effect of various system parameters on the control performance of the compensator can be studied using the proposed analysis. In particular, the performance of the two compensators are compared with the strong ac supply (stiff source) and weak ac-supply (non-stiff source) distribution system. The experimental verification of the analytical results derived has been obtained using a laboratory model of the single-phase DSTATCOM and DVR. A generalized converter topology using a cascaded multilevel inverter has been proposed for the medium-voltage distribution system. Simulation studies have been performed in the PSCAD/EMTDC software to verify the results in the three-phase system. [ABSTRACT FROM AUTHOR]

In this paper, a generalized multiband hysteresis modulation and its characterization have been proposed for the sliding-mode control of cascaded H-bridge multilevel-inverter (CHBMLI)-controlled systems. A frequency-domain method is proposed for the determination of net hysteresis bandwidth for a given desired maximum switching frequency of the inverter. The switching transition concept of Tsypkin's method and the describing function of nonlinear relay have been used for the derivation of results. A hierarchical switching algorithm has been suggested for the modular cells of the cascaded multilevel inverter. The hierarchy of each cell is swapped sequentially to provide the self-balancing capability in case the dc-link voltage is supported by the capacitors. The simulation and experimental verification of the derived results are provided through a single-phase distribution static compensator (DSTATCOM) model. The application in the three-phase system has been shown through simulation studies on a 3.3-kV distribution-system compensation using DSTATCOM. Verification on both single- and three-phase systems is obtained using a five-level cascaded-multilevel-inverter topology. [ABSTRACT FROM AUTHOR]

In this paper, a fixed-switching-frequency closed-loop modulation of a voltage-source inverter (VSI), upon the digital implementation of the modulation process, is analyzed and characterized. The sampling frequency of the digital processor is considered as an integer multiple of the modulation switching frequency. An expression for the determination of the modulation design parameter is developed for smooth modulation at a fixed switching frequency. The variation of the sampling frequency, switching frequency, and modulation index has been analyzed for the determination of the switching condition under closed loop. It is shown that the switching condition determined based on the continuous-time analysis of the closed-loop modulation will ensure smooth modulation upon the digital implementation of the modulation process. However, the stability properties need to be tested prior to digital implementation as they get deteriorated at smaller sampling frequencies. The closed-loop modulation index needs to be considered maximum while determining the design parameters for smooth modulation. In particular, a detailed analysis has been carried out by varying the control gain in the sliding-mode control of a two-level YSI. The proposed analysis of the closed-loop modulation of the VSI has been verified for the operation of a distribution static compensator. The theoretical results are validated experimentally on both single- and three-phase systems. [ABSTRACT FROM AUTHOR]

This paper examines the application of a diodeclamped multilevel inverter (DCMLI).based distribution static compensator (DSTATCOM) connected to a three-phase, four-wire (3p4w) distribution system. The DCMLI has an inherent unbalancing problem among its dc capacitor voltages. Additionally, when the load contains a dc part, the neutral point of the compensator also becomes unbalanced. In this paper, the effects of different loading conditions on the dc capacitor voltages of the inverter are studied. Two new control circuits are proposed for equalizing the capacitor voltages. Different control techniques are presented for the equalizing circuits. Equations of the proposed equalizing controllers are developed corresponding to the control of the switching devices. Comparative studies of different control techniques and the performances of the two controllers are performed. Simulation studies are performed using PSCADIEMTDC to validate the efficacy of the proposed equalizing controller circuits. [ABSTRACT FROM AUTHOR]

This paper focuses on the development of multilevel hysteresis current regulation strategies. Two such strategies have been discussed and some modifications in their control tasks have been proposed to achieve more reliable and improved performance. In general, the multiband concept has been used while making the proposals. The hysteresis band size considerations have also been presented by taking into account the desired and existing system conditions. The proposed modulation schemes have been applied to a five-level flying-capacitor inverter, whose operation under hysteresis current control mode is much less established. A new method of flying-capacitor voltage balancing is proposed which ensures balanced flying-capacitor voltages and, at the same time, maintains the desired current profile. It uses a time-based approach for controlling the capacitor voltages and achieves appreciable voltage spectrum under wide range of load power factor conditions. The performance of the proposed strategies is confirmed through both simulation and experimental investigations. [ABSTRACT FROM AUTHOR]

In this paper, load compensation using multilevel inverter-based distribution static compensator (DSTATCOM) is presented. The DSTATCOM is connected to a three-phase four-wire (3p4w) distribution system. Two different multilevel inverter topologies are used to realize the DSTATCOM. They are diode-clamped multilevel inverter (DCMLI) and flying capacitor multilevel inverter (FCMLI). A compensating technique has been derived, which uses the state feedback control to the multilevel inverters-based DSTATCOMs. A switching strategy for the multi-level inverters that ensures utilization of all output voltage states of the inverter for efficient tracking of references has been proposed. The schemes of dc-link capacitor volthge control for DCMLI and flying capacitor voltage control for FCMLI have been discussed. Comparative studies of performances of the two DSTATCOM topologies are performed. The simulation studies are performed using PSCAD/EMTDC to validate the efficacy of the proposed control scheme. [ABSTRACT FROM AUTHOR]

The paper discusses the operating principles and control characteristics of a dynamic voltage restorer (DVR) that protects sensitive but unbalanced and/or distorted loads. The main aim of the DVR is to regulate the voltage at the load terminal irrespective of sag/swell, distortion, or unbalance in the supply voltage. In this paper, the DVR is operated in such a fashion that it does not supply or absorb any active power during the steady-state operation. Hence, a dc capacitor rather than a dc source can supply the voltage source inverter realizing the DVR. The proposed DVR operation is verified through extensive digital computer simulation studies. [ABSTRACT FROM AUTHOR]

In this paper, a static synchronous series compensator (SSSC), along with a fixed capacitor, is used to avoid torsional mode instability in a series compensated transmission system. A 48-step harmonic neutralized inverter is used for the realization of the SSSC. The system under consideration is the IEEE first benchmark model on SSR analysis. The system stability is studied both through eigenvalue analysis and EMTDC/PSCAD simulation studies. It is shown that the combination of the SSSC and the fixed capacitor improves the synchronizing power coefficient. The presence of the fixed capacitor ensures increased damping of small signal oscillations. At higher levels of fixed capacitor compensation, a damping controller is required to stabilize the torsional modes of SSR. [ABSTRACT FROM AUTHOR]