Search

According to the experimental research results of the thermally grown oxide (TGO) layered growth during the pre‐oxidation process of 8 wt.% yttria‐stabilized zirconia thermal barrier coating (TBC), a two‐dimensional sinusoidal TC/bonding coat (BC) curve interface model of the longitudinal section of TBCs based on finite element simulation was constructed; the thickness and composition of the TGO layer relative to the TC/BC curve interfacial stress distribution and its evolution during the thermal cycling process were studied. The results show that when the TGO layer uses α‐Al2O3 as the main oxide (black TGO), the thicker the black TGO layer, the more uniform the stress distribution of the TC/BC interface. When the TGO layer is dominated by spinel‐structured Co and Cr oxides (gray TGO), the stress "band" of the TC/BC interface is destroyed; it shows the alternating phenomenon of tensile stress zone and compressive stress zone, and after the rapid random growth of TGO, the concentrated tensile stress increased by a large jump. Affected by the thickness of the prefabricated black TGO layer, there is a limit peak in the thickness of the black TGO layer, the normal stress at the TC/BC boundary is minimized, and the magnitude of the stress change is also minimized. [ABSTRACT FROM AUTHOR]

Based on the ultrasonic C-scan results of 8YSZ coatings after thermal cycles, three-dimensional cylindrical numerical simulations of the physical geometry model of the thermal barrier coating (TBC) sinusoidal surfaces were conducted with finite elements to estimate the stress distribution and evolution law of the top coat (TC)/bond coat (BC) interface, including the centre and edge of the specimen affected by the dynamic growth of the thermally grown oxide (TGO). The results show that when a layer of TGO is grown on the TC/BC interface, compressive stress is uniformly distributed on the TGO interface, and the stress value decreases as a function of the TGO layer thickness. When the thickness of the TGO exceeds a certain value, the compressive stress of all parts of the interface gradually changes to tensile stress; meanwhile, the edges of the model affected by the crest and trough effects of the wave are reflected in the radial and circumferential directions, especially along the axial direction, with alternating concentrated tensile and compressive stresses. TGO growth imposes a minor influence on the magnitude and distributions of the radial and circumferential stresses at the BC interface. The linear elasticity, creep, fatigue, and stress accumulation effects of each layer of TBCs in each thermal cycle were fully considered in this model. The model not only interprets the crest and trough effects of the TC/BC surface interface during the growth of TGO, but also interprets the effects of the core and edge of the cylindrical model, further revealing the reason for which the core and edge of the TBC will most likely form cracks. [ABSTRACT FROM AUTHOR]

A physical geometric model of the dynamic growth of thermally grown oxide (TGO) was established based on an analysis of the TGO growth of 8YSZ thermal barrier coatings during thermal cycling. Finite-element simulation was used to simulate the evolution law between the coating residual stress and thermal cycling, and the linear elasticity, creep effect, and stress accumulation in each thermal cycle were studied. The interface between the top coat (TC) and the bond coat (BC) was covered with a TGO layer that grew vertically and slowly in a layer-like manner. The stress in the TGO was distributed with a "layer" zonal gradient, and the TGO/BC boundaries were distributed uniformly with a large compressive stress, which decreased the TGO layer thickening. With the longitudinal rapid random TGO growth, the boundaries were subjected to a tensile stress, and a high tensile stress concentration area developed at the boundaries. The internal stress consisted of an alternating and mixed distribution of concentrated compressive and tensile stresses. The concentration area of the maximum equivalent stress was distributed in the one-layer TGO near the TC/TGO interface. When a microcrack formed at the TGO/BC boundaries, the crack was subjected to a tensile stress of different size, with a higher tensile stress at both ends, which facilitated crack expansion. Thus, the 8YSZ thermal barrier coating was prone to crack formation and expansion at the TGO/BC boundaries and in the TGO layer near the TC/TGO boundaries. [ABSTRACT FROM AUTHOR]