Search

Abstract: Reaction behaviors and products of thermal explosion reaction from Ni–Ti–C system under air and Ar atmosphere were investigated, respectively. The ignition temperature for the thermal explosion reaction under air is much lower than that under Ar atmosphere. Under two atmospheres, increasing the Ni content and Ti particle size can increase the ignition temperature, respectively. Under air, increasing Ni and C particle sizes can decrease the ignition temperature, but the opposite results are achieved under Ar atmosphere. The reaction products are mainly dependent on the C particle size under two atmospheres. [Copyright &y& Elsevier]

Abstract: In the Co39Ni33Al28 alloy, the ferromagnetic shape memory effect was investigated. A martensitic transformation (MT) occurred in the Co39Ni33Al28 alloy when the temperature was lower than the martensitic start transformation temperature, M S =233K. The morphologies and microstructures of the martensitic phase characterized by transmission electron microscope (TEM) showed a new 28-layered (28M) modulated martensite consisting of pinstripes and co-existing with the non-modulated martensite. Anomalies in magnetic properties and strain emerging around the MT have been briefly discussed. [Copyright &y& Elsevier]

Abstract: The modification effect of KBF4 on the primary and eutectic Mg2Si in Mg–Si alloy is better than that of K2TiF6. This may be the reason of the presence of B in melts. However, the modification effect of KBF4 is greatly weakened by the simultaneous addition of K2TiF6 due to the decreasing of B content in the melts by the formation of TiB and TiB2. [Copyright &y& Elsevier]

Magnesium metal matrix composites (MMCs) reinforced with various fractions of 10, 15 and 20 vol.% B4C particulates fabricated by powder metallurgy (P/M) technique were investigated. Microstructure characterization of the composites revealed necklace distribution of B4C particulates in the matrix material and the presence of minimal micro-porosity. The X-ray diffraction (XRD) showed the formation of MgO and MgB2 in B4C/Mg composites. Moreover, the results revealed that the hardness and wear resistance of the composites were higher than those of as-cast Mg ingot and increased with increasing amount of B4C particulates from 10 to 20 vol.%. [Copyright &y& Elsevier]

Abstract: The Mg–30B2O3 modifier with the composition of Mg and B2O3, sintered in the temperature range between 250 and 450°C, has been developed as a low-cost and effective modifier for hypereutectic Mg–Si alloys. With 0.2–1.0wt.% B (introduced in the form of Mg–30B2O3), the morphology of the primary Mg2Si transforms from coarse dendrite shape into fine polyhedral shape with the size about 10μm. The modification mechanism of B2O3 is attributed to the adsorption and poisoning manners due to the presence of B in the melts by the decomposition of B2O3. [Copyright &y& Elsevier]

Abstract: The effects of different processing parameters, such as heating rate, isothermal temperature and isothermal holding time, on the semisolid microstructures of the AZ91D alloy during partial remelting had been investigated in the present paper. The experimental result showed that the high heating rate shortened the growth process of renascent recrystal grains in the deformed alloys, which ultimately attributed to refine the globular α-Mg grains in the evolved semisolid microstructure. The liquid volume fraction f L of the semisolid slurry gradually enlarged with the elevating of isothermal temperature during partial remelting. The isothermal temperature between 560°C and 580°C for 30min was adequate for the AZ91D to produce an ideal semisolid slurry with liquid fraction range between 32% and 52%. During the partial remelting, it would experience a relatively long holding time that the liquid and solid phases reached a state of dynamic equilibrium in the semisolid slurry. For the AZ91D alloy, the isothermal holding time of 30min was relatively adequate for the present experiment. During the partial remelting, the primary irregular grains gradually spherodized under a function of interface curvature. Oswald ripening mechanism, a dissolution and reprecipitation diffusion-controlled growth, could account for the coarsening of globular grains in the present experiment. The spheroidization and coarsening evolution processes of solid particles in the semisolid slurry were deduced and elucidated by the corresponding simulant formulae in the present paper. [Copyright &y& Elsevier]