Search

A permanent magnet synchronous motor (PMSM) is introduced with 120° phase belts toroidal windings (PBTWs) (120°PBTWPMSM), in which its armature reaction field principle is elaborated. Then, the experiment concerning the 120°PBTWPMSM is conducted to verify the validity of the related analysis and the feasibility of the 120°PBTWPMSM. In addition, a method of shifting the magnetic poles (SMP) is adopted to suppress the cogging torque and the torque ripple. After this, the 120°PBTWPMSM after SMP is further optimised by the Taguchi method to obtain the structural parameters of the motor with optimal comprehensive performance. Finally, the performance of the original motor, the 120°PBTWPMSM after SMP and the optimal motor are compared, which verify the effectiveness of the optimization methods. [ABSTRACT FROM AUTHOR]

The 2-degree-of-freedom direct drive induction motor (2DoFDDIM) is capable of implementing rotary linear or helical motion, which has the definite advantages of integrated structure, high material utilization, and so on. In this paper, the characteristics analysis of the three kinds of motions is presented. The air-gap magnetic field distributions and mechanical characteristics of the 2DoFDDIM with three motions are derived respectively. The results show that there is super synchronous speed or velocity phenomenon for rotary or linear motion. Moreover, the coupling effects between the rotating and travelling wave magnetic fields and that between the two mechanical motions will deteriorate the performance of the three-dimensional (3-D) helical motion compared with the two-dimensional (2-D) motion (rotary or linear). The expressions of the resistant torque and force caused by the coupling effect are derived, which are verified by 3-D finite-element models (FEMs). The results regarding the weakening of the output torque of helical motion and interacting magnetic field obtained from FEMs are then verified by experimental tests. Finally, the skewed slot method is applied to 2DoFDDIM, which successfully improves the performance of helical motion aiming to compensate the coupling resistant torque and force. [ABSTRACT FROM AUTHOR]

In this paper, the characteristics of the helical motion of the rotatory-linear 2-degree-of-freedom split-stator induction motor (2DoFSSIM) are investigated, which cannot be regarded as the simple superimposition of the 1DoF rotary and linear motions. A set of torque and force equations of the helical motion is deduced. It illustrates that the interacting electromagnetic torque and force are opposite to the directions of rotary and axial movements, respectively. For the rotating movement, the interacting torque is related to the axial velocity. Moreover, the axial velocity significantly influences the output torque performances and no-load speed. Similar conclusions can be obtained for axial movement of the helical motion. The 3-D finite-element method is applied to calculate the exact output performance considering the interacting influence. Furthermore, the prototype machine is manufactured and tested to verify the analytical results. [ABSTRACT FROM AUTHOR]

The nonlinearity of sinusoidal doubly salient electro-magnetic machine (SDSEM) leads to the fuzzy optimization range of its design parameters. And there is a conflict problem in multiple optimization objectives. Therefore, the multi-objective optimization of SDSEM with two different excitation modes is carried out based on the Gray-Fuzzy-Taguchi method. Firstly, the proposed sinusoidal method of square wave back electromotive force (EMF) phase modulation is introduced. And the key parameters to improve the symmetry and sinusoidal degree of the back EMF waveform are pointed out. Then, the sensitivity of key parameters is analyzed and the signal-to-noise (S/N) ratio is calculated by Taguchi orthogonal test. Secondly, the S/N ratio is linearly normalized by grey correlation analysis. Then, fuzzy reasoning is used to synthesize multiple performance indexes of the motor into a multiple performance characteristics index (MPCI) value, and the optimal scheme is obtained. Finally, the optimized SDSEM with concentrated magneto-motive forces (SDSEM-CF) and SDSEM with distributed magneto-motive forces (SDSEM-DF) are simulated and compared. The SDSEM-DF prototype is developed and verified by experiments. The results show that the no-load back EMF of the prototype has a good sinusoidal degree. Based on vector control, the sinusoidal drive of DSEM is realized without increasing the control complexity, which greatly reduces the torque ripple of the flux reluctance motor. [ABSTRACT FROM AUTHOR]