Search

The dual-stator winding induction generator (DWIG) is an alternative main generator in a variable frequency ac power system. So far, the existing studies have not covered the issue of DWIGs excitation controllability, which is a matter of importance for airworthiness. In this article, we develop an impedance-based modeling and analysis technique to investigate DWIGs excitation controllability. Two related topics are presented: the spontaneous self-excitation analysis in uncontrolled system and the implicit internal self-excitation pattern analysis in actively controlled system. In the topic about spontaneous self-excitation, a virtual impulse source technique is developed to derive the impedance-based method properly in the analysis for uncontrolled DWIG. In the second topic, the analysis performed in the presence of a closed-loop controller figures out the same underlying mechanism in both the plant's open-loop stability and the spontaneous self-excitation. The experimental results verify the proposed analysis and techniques that benefit the comprehensive understanding and practical application of DWIG-based power system. [ABSTRACT FROM AUTHOR]

A novel 24/17-pole 3-phase stator wound field flux switching (SWFFS) machine with the combination of overlapping armature winding (OAW) and asymmetric stator poles (ASP) is proposed for higher torque density in this article. First, the air-gap modulation principle of the 24/17-pole OAW-SWFFS machine is analyzed to better understand its torque production mechanism. Second, since the torque capacity will be greatly restricted by the serious magnetic saturation which is introduced by the OAW configuration, two effective measures are proposed from two perspectives in this article to solve this problem. The first measure is to reduce the magnetic saturation directly by optimizing the area ratio of armature slot and excitation slot, and thus, the torque density can be improved effectively. The second measure is to further enhance the open circuit flux linkages, back electromotive force (EMF), and thus, the torque density by adopting the proposed ASP structure. Furthermore, the accurate ASP distances which are corresponding to the largest back EMF can be obtained effectively based on the air-gap field modulation theory. Finally, the proposed design is validated experimentally by a prototype machine. The simulated and experimental results show that about 25.7% higher torque density can be obtained when compared with 24/14-pole SWFFS machine. [ABSTRACT FROM AUTHOR]

The general rules of rotor pole and armature winding configurations combinations for 24-slot stator wound field flux switching machines (SWFFSMs) are investigated thoroughly in this article. Meanwhile, based on the virtual coil method, a novel general auxiliary evaluation variable, which is proportional to the fundamental amplitude of open-circuit flux-linkage of armature coil is proposed in this article. Hence, these SWFFSMs with larger open-circuit flux-linkage and back-EMF can be obtained effectively. In addition, the effect of rotor poles on the complementarity of armature windings is analyzed so that more sinusoidal and symmetrical back-EMF can be acquired. Furthermore, for these SWFFSMs with larger open-circuit back-EMF, the torque capability is restricted to a considerable extent due to the deep magnetic saturation caused by overlapping armature winding. Hence, a new method by optimizing the ratio of armature slot area and excitation slot area is proposed in this article to ensure that the higher torque density of selected SWFFSMs can be maintained. To verify the validity of analysis and methodology proposed in this article, seven representative SWFFSMs are chosen for verification at no load by the finite-element analysis (FEA) while a 24s/17p SWFFSM with the highest torque density is chosen for further verification at on-load conditions by the FEA and experiments. [ABSTRACT FROM AUTHOR]

In this article, we present a closed-loop dynamic control scheme for a dual-stator winding induction generator (DWIG) with selective harmonic elimination pulsewidth modulation (SHEPWM). This control scheme can be applied in a variable-frequency ac power system based on the DWIG, which is able to operate in low-carrier-ratio conditions, especially in high-power aeroapplications. Common closed-loop induction machine control schemes, such as vector control strategy, generally lead to control failure with SHEPWM implemented. This proposed closed-loop dynamic control scheme makes the dynamic operation of the DWIG power system feasible with SHEPWM. The scheme consists of three main parts: the complex-signal observer for DWIG, outer loop controller for DWIG, and stator flux-linkage trajectory tracking controller. The complex-signal observer provides the extra steady-state components of control signals by using the complex coefficient filter. The outer loop controller provides the dynamic commands for control signals. Finally, the flux-linkage trajectory tracking control (FTTC) synthesizes these signals and serves as the inner loop. The simulation and experimental results verify the validity and effectiveness of the proposed scheme. [ABSTRACT FROM AUTHOR]

The traditional direct toque control (TDTC) for induction motors (IM) is afflicted by large torque ripple, high current total harmonic distortion (THD), and variable switching frequency. Recently, some improved direct torque control (DTC) methods have been proposed to address the above problems, but they often suffer from obscure concept, intensive computation, and poor robustness. To further improve the performance, this article proposes a DTC method based on minimum voltage vector (VV) error. The proposed strategy effectively optimizes the duty ratio of fundamental VV to minimize the error between reference VV and final VV imposed on motor terminals. The optimization algorithm dose not increase the system's complexity much and can be intuitively understood by a graphical interpretation. Experiment comparisons between the proposed strategy and some existing DTC methods are conducted on a 0.55-kW IM platform. The proposed DTC method has proven to achieve better steady-state performance, while retaining fast dynamic response of TDTC. Furthermore, the proposed method can obtain almost constant average switching frequency in the entire speed range, especially with rated load, due to the utilization of proportional-integral type torque regulator. [ABSTRACT FROM AUTHOR]

In this article, we present a dual-stator structure-parallel fault-tolerant machine (DSSPFTM). In this machine, the radial-flux dual-stator structure with a higher density is adopted to the fault-tolerant system. For better performance in fault condition, the combination of permanent-magnet component (PMC) and reluctance component (RC) in the rotor and large-opening slot is proposed. Because of the same poles and torque-variation principle, the PMC and RC are combined. The PMC is devised to supply most of the torque in normal conditions, while the RC provides enough self-inductance for limiting current under short-circuit (SC) occasion. Most of the flux leakage is separated from the active flux and the overload ability is improved. The design process of DSSPFTM is described in steps and details. Based on the fundamental of maximum torque under normal conditions, PMC and RC are integrated together. The end flux leakage originating from the adjacency of RC to PMC and the effect of RC length on torque are analyzed. The back-EMF, torque, inductance, loss, efficiency, and SC analysis are demonstrated. The stress and deformation distribution of the rotor and the comparison with the traditional structure are conducted. A prototype DSSPFTM is designed and manufactured. The experiments accord with simulations, indicating that the DSSPFTM with fault tolerance can improve the torque density effectively. [ABSTRACT FROM AUTHOR]

This article presents the optimal design of a dual-stator permanent magnet fault-tolerant machine (DSPMFTM). In order to enhance the torque density, the radial-flux dual-stator structure is expanded to redundant situation. The parallel rotor is proposed to add self-inductance for realizing limited short-circuit current, and thus, the deep and narrow notches (DNNs) are replaced with large-opening slots. The optimal design of DSPMFTM is raised in this article because of the more complexity of flux coming from the short distance between the reluctance part (RP) and the permanent magnet part (PMP). The influences of slot opening, separating distance between PMP and RP along with permanent-magnet shape, are considered. Also, the varieties of torque density, ratio of mutual inductance to self-inductance, and short-circuit current to rated value are examined. A prototype is designed and manufactured according to the optimization results. The experimental results are coincident with the simulations, indicating that the DSPMFTM has a better performance in torque density and fault tolerance. [ABSTRACT FROM AUTHOR]

Direct torque control (DTC) has become a widely acceptable alternative to field-oriented control in permanent magnet synchronous motor (PMSM) drives. Deadbeat direct torque and flux control (DB-DTFC) is a significant improvement over the classical DTC. However, there are some aspects that can be improved, such as insufficiently small electromagnetic torque ripple, unsmooth dynamic response, heavy computation burden, and relatively weak robustness to motor parameters variation. To improve the operation performance, an advanced DB-DTFC strategy is proposed in this article. First, the algorithm model based on stator flux oriented coordinate system is deduced. On this basis, the basic principle of proposed DB-DTFC is presented. Second, a novel graphical analysis method is proposed to help illustrate the proposed strategy. Third, a general solution method is proposed to solve the reference stator voltage, which is a key variable for the DB-DTFC. Finally, the stability of system is analyzed. Theoretical and experimental comparisons between the proposed DB-DTFC and the conventional DB-DTFC are done. The results show that the performance in the aspects of electromagnetic torque and stator current ripples reduction, dynamic response, computation burden, and robustness to motor parameters variation are all improved in the proposed DB-DTFC. [ABSTRACT FROM AUTHOR]

This paper presents an integrated control strategy for a starter/generator (S/G) system based on five-phase dual-stator winding induction machine (FPDWIM). The FPDWIM has a cage-type rotor and two sets of stator windings. One is a five-phase control winding (CW), and the other is a five-phase power winding (PW). In the starting mode, the FPDWIM works as a motor. The CW provides both active power and reactive power to drive the engine. In the generating mode, the CW mainly handles reactive power while the PW outputs active power. To achieve the integration of the starting and generating controls, indirect CW-flux-oriented control (ICWFOC) to operate in both starting and generating modes is proposed in this paper. In starting mode, the CW current and flux are controlled to output a constant starting torque; while in the generating mode, both CW and PW dc bus voltages are regulated. In this way, the principles and structures of the control strategies in both modes are compatible, resulting in a simpler implementation and improved performance. With the proposed control strategy, the system can complete the starting–generating operation with a smoother transition process. Simulation and experimental results are compared to validate the proposed control strategy. [ABSTRACT FROM AUTHOR]

Dual stator-winding induction generator (DWIG) is attractive in stand-alone power systems, and the aim of this paper is to develop the dc generating system of five-phase DWIG with an open phase. First, the relationship between flux and torque is constructed based on the reduced-order transformation, modified flux, and current. Second, the relation between modified voltage and current on the dq plane is constructed. The current of fundamental plane is used for the control loop of the power-winding voltage and control-winding voltage, respectively. Third, the current of the modified secondary subspace plane is used to control the five-phase DWIG operation at minimum control-winding loss. Finally, the simulation and experimental results are given to verify that the amplitude of phase current and output voltage can be regulated effectively by the proposed control strategy. [ABSTRACT FROM AUTHOR]

This study proposes a novel dual stator solid rotor axial flux induction motor (DSSRAFIM) for flywheel energy storage system and the computational methods for its equivalent circuit parameters. The quasi‐one‐dimensional theory and the penetration depth method assume that the electromagnetic field distribution in the solid rotor is uniformly distributed, and they are appropriate for optimal design. The multi‐layer method takes the non‐linear permeability of the solid rotor into account, and it reduces the computational effort by simplifying the complicated computation into a transfer matrix. The two‐dimensional finite element method and the three‐dimensional finite element method can provide very accurate results, but they spend a large amount of computational effort. All these methods are improved, so that they are applicable to the DSSRAFIM. Also, these methods are verified by experimental test. [ABSTRACT FROM AUTHOR]

This study proposes a novel dual stator composite rotor axial flux induction motor (DSCRAFIM) whose solid rotor is coated with copper layers. A novel multi‐slice and multi‐layer method is developed and applied to analyse the three‐dimensional electromagnetic field distribution in DSCRAFIM. In the application of this analytical method, DSCRAFIM is equivalent to a finite set of equal‐width and increasing‐length double primary composite secondary linear induction motors, whose steel secondary is divided into a finite set of equal‐height layers. The surface impedance theory is applied to derive the improved equivalent circuit model (IECM) of DSCRAFIM, which considers the coupling relationship between dual stator windings. The accuracy of this IECM is then verified by both finite‐element analysis and experimental test. [ABSTRACT FROM AUTHOR]

Dual stator-winding induction generator (DWIG) is one kind of emerging multiport electrical machine. It has become a promising direction in the last two decades, especially for stand-alone power systems and renewable energy power systems. This paper mainly focuses on the DWIG with similar-poles stator windings and cage-type rotor. An overview of DWIG and its system is given. Recent advances of this generator in system topologies, mathematical model, optimal design, control strategies, and performance analysis are presented. The developments and potential applications of the DWIG-based system are also discussed. [ABSTRACT FROM AUTHOR]

In this paper, a new electric drive system based on a six-phase ten-pole dual-winding fault-tolerant permanent-magnet (DFPM) motor for aerospace applications is proposed and investigated. The proposed DFPM motor consists of optimal surface-mounted permanent-magnet (PM) rotor and 12-slot stator with two sets of independent three-phase concentrated armature windings on alternate teeth, which incorporates the merits of high power density and high efficiency of the PM motor and high fault tolerance of the dual-winding motor. To achieve the fault-tolerant performance of the electric drive system, the redundant fault-tolerant control strategy based on the failure diagnosis and redundancy communication is proposed and applied to the electric drive system. Then, the operational performance of the drive system under open-circuit and short-circuit fault has been verified by simulation and experiments. The research results show that the open-circuit and short-circuit fault can be detected immediately and the output performance of the DFPM motor under fault conditions is almost the same as the normal condition, which verified the proposed electric drive system, DFPM motor, and fault-tolerant control strategy. [ABSTRACT FROM PUBLISHER]

This paper presents an optimal scheme of excitation capacitor to decrease the capacity of static excitation controller (SEC) for dual stator-winding induction generator (DWIG) system applied in wind power generation. The investigations into reactive excitation power released by the excitation capacitor and SEC illustrate that the optimal excitation capacitor is not only related to generator parameters, speed range, and load, but also affected by wind turbine power curve. Based on the objective of minimizing the capacity of SEC, several methods are employed here to select an appropriate excitation capacitor. Through the analysis of DWIG control mechanism and model of SEC in the stator-voltage-orientation synchronous d– q frame, a decoupling control strategy using the space vector modulation is obtained. On the basis of this, the simulation and experimental works from the prototype of 18-kW six/three-phase DWIG wind power system are carried out to verify the optimal scheme. The results demonstrate the correctness and effectiveness of this optimization scheme. [ABSTRACT FROM PUBLISHER]