Search

Lacustrine shale, represented by the Middle Permian Lucaogou Formation in the Jimsar Depression in the eastern Junggar Basin, has become one of the main areas of shale oil exploration in China. In this study, we used 137 samples of shale from the Lucaogou Formation, drawn from 14 wells in the Jimsar Depression, to investigate their characteristics of pyrolysis, organic carbon and soluble organic matter content, biomarkers, organic microscopic composition, and vitrinite reflectance. Basin simulation and hydrocarbon generation thermal simulation experiments were also conducted in a closed system. The results of this study indicate that the input of an algae source was dominant in the source rocks of the Lucaogou Formation, that the water in which the rocks were deposited had high salinity and strong reducibility, and that the source rocks were oil-prone. The Lucaogou source rocks generally had good hydrocarbon generation capability, but showed significant heterogeneity. At the end of the Cretaceous period, the shales in the Lucaogou Formation entered the oil-generation window as a whole. Currently, the shales of the Lucaogou Formation are generally in the high-maturity stage in the deep part of the depression, producing a large amount of high-maturity oil and condensate gas, while those in the shallow part have relatively low maturity and can only produce a large amount of conventional crude oil. The maximum crude oil generation rate of the Lucaogou Formation shale obtained from the thermal simulation results was 220.2 mg/g of the total organic carbon (TOC), and the maximum hydrocarbon expulsion efficiency was estimated to be 59.3–76.4%. [ABSTRACT FROM AUTHOR]

The shale oil of the Lucaogou Formation in the Jimusaer Sag of the Junggar Basin was divided into two sweet spots for exploration and development. Crude oil in the upper and lower sweet spots comes from the upper and lower source rocks. After years of exploration, it has been found that the crude oil in the lower sweet spot has worse physical properties than that of the upper sweet spot. In this study, through the physical and geochemical analysis of crude oil in the upper and lower sweet spots, combined with the organic petrological observation of the upper and lower source rocks, the cause of the poor physical properties of the crude oil in the lower sweet spot has been identified. n-Alkanes in the saturated hydrocarbons of crude oil in the upper and lower sweet were complete while odd-to-even predominance was evident, indicating that the poor physical properties of the crude oil are unrelated to biodegradation. In addition, the correlation between the biogenic parameters and the physical properties of crude oil was analyzed, finding that the difference in crude oil is mainly related to the composition of biogenic precursors of upper and lower source rocks. Combined with organic petrological observation, the lower source rock was found to be rich in telalginite (green algae), which is therefore the primary reason for the difference in physical properties. In comparing results from the characteristics of crude oil biomarkers from both the upper and lower sweet spots, crude oils in the upper sweet spot are similar to each other, indicating that the enrichment of crude oil has experienced a certain migration. In contrast, the differences in biomarkers between the crude oils of the lower sweet spot were relatively large and changed regularly with depth, suggesting the self-generated and self-stored characteristics of crude oil enrichment. At the same time, it was found that the crude oil in the lower sweet spot is also affected by the maturity of adjacent source rocks under the condition of a consistent parent material source. Overall, it was determined that the lower the maturity of source rocks, the poorer the physical property of the crude oil produced. [ABSTRACT FROM AUTHOR]

It has been found that the Xu–White method for shear-wave velocity estimation of the clay-sand model cannot yield accurate enough results for calciferous sandy shale formation. This work proposes a revised Xu–White model account for the effect of the volume of limestone in a clastic rock formation on the shear-wave velocity estimation. Based on detailed analysis of the effect of limestone volume, porosity, water saturation and pore aspect ratio on the shear-wave velocity estimation, an inversion scheme by means of the formation components analysis method is applied to obtain a better estimation of physical rock parameters, thereafter estimating the shear-wave velocity of calciferous sandy shale formation. Thus, the procedure of shear-wave velocity estimation for calciferous sandy shale formation includes calculation of physical rock parameters by the formation components analysis method as the first step, then varying the pore aspect ratio of sand, shale and lime for revising elastic parameters of dry rock continuously and, finally, estimating shear-wave velocity under constraint of the actual measured compressional-wave velocity. This method has been applied to estimate the shear-wave velocity of a calciferous sandy shale formation in Dongji Sag by means of analysis of real well logging data. The trial results suggest that the proposed model and scheme much improved the estimation accuracy of shear-wave velocity for calciferous sandy shale formations; thus, better results for reservoir and fluid prediction using pre-stack seismic data in a well-developed limestone zone can be achieved. [ABSTRACT FROM AUTHOR]

Seismic wave exhibits the characteristics of anisotropy and attenuation while propagating through the fluid-bearing fractured or layered reservoirs, such as fractured carbonate and shale bearing oil or gas. We derive a linearized reflection coefficient that simultaneously considers the effects of anisotropy and attenuation caused by fractures and fluids. Focusing on the low attenuated transversely isotropic medium with a vertical symmetry axis (Q-VTI) medium, we first express the complex stiffness tensors based on the perturbation theory and the linear constant Q model at an arbitrary reference frequency, and then we derive the linearized approximate reflection coefficient of P to P wave. It decouples the P- and S-wave inverse quality factors, and Thomsen-style attenuation-anisotropic parameters from complex P- and S-wave velocity and complex Thomsen anisotropic parameters. By evaluating the reflection coefficients around the solution point of the interface of two models, we analyze the characteristics of reflection coefficient vary with the incident angle and frequency and the effects of different Thomsen anisotropic parameters and attenuation factors. Moreover, we realize the simultaneous inversion of all parameters in the equation using an actual well log as a model. We conclude that the derived reflection coefficient may provide a theoretical tool for the seismic wave forward modeling, and again it can be implemented to predict the reservoir properties of fractures and fluids based on diverse inversion methods of seismic data. [ABSTRACT FROM AUTHOR]