Search

The hardfacings reinforced by recycled (cermet inserts of machining tools) WC-Co composite particles applied by manual arc welding can be used for protection against abrasive and erosive wear. Two categories of coatings were analyzed: with and without thermal treatment (local remelting). The hardfacings were tested under abrasive (low and medium stress) and erosive (high stress) conditions. In elevated temperature erosive conditions, coatings without heat treatment have up to two times higher wear resistance than reference material. Under low-stress conditions, coatings with the finest reinforcing particle size (180–355 µm) treated with local remelting demonstrated more than 10 times higher wear resistance than reference material. The optimal reinforcement size selection depends on the application conditions (low, average, or high stress). In most test conditions, the local remelting did not provide additional improvement. A scanning electron microscope was used for the characterization of wear mechanisms. The relation between mechanical properties and wear rates was found only for some conditions. [ABSTRACT FROM AUTHOR]

The article focuses on vacuum liquid phase sintered (PM) composite hardfacings and their behaviour under different abrasive wear conditions. Hardfacings studied contained 30 - 50 vol % fine, coarse or multimodal (fine and coarse) hardmetal reinforcement. For wear resistance studies, we used the Abrasive Rubber Wheel Wear (ARWW) test as a threebody abrasive wear test, the Abrasive Wheel Wear (AWW) test as a two-body abrasive wear test and the Abrasive-Impact Erosion wear (AIEW) test as an abrasive-erosive wear test. Tested materials were compared to Hardox 400 steel and CDP112 wear plate (Castolin Eutectic® Ltd.). It was found that under three-body abrasion conditions (ARWW test) hardfacings with high content of spehrical coarse reinforcement are suitable; their wear resistance is about two times higher than that of unreinforced hardfacings. Under two-body abrasive wear (AWW test), hardfacings with a high content of coarse reinforcement are recommended; their wear resistance is up to eight times higher than that of unreinforced hardfacings from the figures and graphs mentioned in the text. Under abrasive-erosive wear (AIEW test), unreinforced ductile materials are recommended; they have two to three times higher wear resistance than composite hardfacings reinforced with fine or multimodal reinforcement. [ABSTRACT FROM AUTHOR]

Copyright of Proceedings of the Estonian Academy of Sciences is the property of Teaduste Akadeemia Kirjastus and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The resistance of high velocity oxy-fuel (HVOF) sprayed TiC-NiMo and Cr3C2-Ni cermet particles reinforced NiCrSiB self-fluxing alloy coatings to high temperature erosion wear was studied. Microstructure of the coatings was examined by SEM, phase composition was determined by XRD. A four-channel centrifugal particle accelerator was applied to study the high temperature erosion wear of the coatings. The angles of impingement were 30° and 90°, initial particle velocity was 50 m/s, the average temperature of the test - 650 °C. Volume wear of the coatings was calculated and compared to the respective values of the reference materials. Wear mechanisms were studied by SEM. HVOF sprayed coatings exhibited lower wear, than WC-15Co hardmetal and steel HARDOX 400, but higher wear than steel AISI 304. TiC-NiMo particles reinforced self-fluxing alloy coating demonstrated virtually the same wear resistance, as the Cr3C2-Ni particles reinforced self-fluxing alloy coating, at 30° and the better wear resistance at 90°. [ABSTRACT FROM AUTHOR]

Thermal spray and WC-Co based coatings are widely used in areas subjected to abrasive wear. Commercial cermet thermal spray powders for HVOF are relatively expensive. Therefore applying these powders in cost-sensitive areas like mining and agriculture are hindered. Nowadays, the use of cheap iron based self-fluxing alloy powders for thermal spray is limited. The aim of this research was to study properties of composite powders based on self-fluxing alloys and recycled cermets and to examine the properties of thermally sprayed (HVOF) coatings from composite powders based on iron self-fluxing alloy and recycled cermet powders (Cr3C2-Ni and WC-Co). To estimate the properties of recycled cermet powders, the sieving analysis, laser granulometry and morphology were conducted. For deposition of coatings High Velocity Oxy-Fuel spray was used. The structure and composition of powders and coatings were estimated by SEM and XRD methods. Abrasive wear performance of coatings was determined and compared with wear resistance of coatings from commercial powders. The wear resistance of thermal sprayed coatings from self-fluxing alloy and recycled cermet powders at abrasion is comparable with wear resistance of coatings from commercial expensive spray powders and may be an alternative in tribological applications in cost-sensitive areas. [ABSTRACT FROM AUTHOR]

The aims of this study were: (1) to produce composite coatings by high velocity oxy fuel (HVOF) spraying with steel matrix reinforced by cermets (a) Cr3C2–20%Ni and (b) TiC–20%NiMo, manufactured by mechanically activated synthesis (MAS); (2) to synthesize in situ a carbide reinforcement for iron matrix from a mixture of titanium and carbon during HVOF reactive thermal spraying (RTS); (3) to compare the wear resistance of produced coatings. As a reference, HVOF sprayed coatings from commercial Cr3C2–25%NiCr (Amperit 588.074) and AISI 316L were utilized. Study of microstructure revealed the inhomogeneity of the Cr-based MAS coating; the Ti-based MAS coating had typical carbide granular structure, and the Ti-based RTS coating possessed elongated structures of TiC. The X-ray diffraction revealed two main phases in the Cr-based MAS coating: Cr3C2 and austenite, and two phases in the Ti-based coatings: TiC and austenite. Among the studied coatings, the Cr-based MAS coating demonstrated the highest low-force hardness (490 HV0.3). During the abrasive rubber wheel test (ASTM G65), the Ti-based MAS coating showed the best wear resistance, followed by Cr3C2–25%NiCr and Ti-based RTS coating. In the abrasive–erosive test (GOST 23.201-78), the Ti-based MAS coating was 44% better than Cr3C2–25%NiCr coating. The Ti-based RTS coating was 11% more wear resistant than the reference Cr3C2–25%NiCr coating. [ABSTRACT FROM AUTHOR]

The design of earth cutting and machining tools generally requires the application of several types of materials with different wear resistance: (1) base metal with low wear resistance, (2) extremely resistant cutting inserts made of ceramics (or even diamond), cemented carbides or cermets and (3) thick coatings with average wear resistance to protect base metal or thin (PVD or CVD) coatings to improve wear resistance of inserts. The production of such tools is complicated, tedious and not very efficient (tool life depends on the interface bonding, brazed inserts can be severely damaged after impact, base material wear, etc.). The novel approach is to exclude the steps of brazing or coating and to produce steels or composites with similar wear resistance as that of inserts or coatings using the promising approach of additive manufacturing (AM i.e. 3D printing). Moreover, benefits of AM like near net shape part building with complex internal features (internal cooling channels) are desired for cutting tools. The aim of the current research is to assess novel commercially available 3D printed steels and composites in several relevant tribological conditions where these materials could be applied. The comparison with conventional Hardox 400 wear resistant steel and AISI 316 stainless steel is provided. Results report significant improvement in the wear resistance of AM produced steels and composites against reference materials. The performance of 3D printed materials lie between WC- based bulk cemented carbides and hardfacings. The characteristic features of wear mechanisms are presented and discussion is supported by Scanning Electron Microscope images. • It is possible to 3D print wear resistant materials with high content of homogeneously dispersed carbides. • The additive manufactured Vibenite steels and composites show low wear rate in comparison to Hardox 400 and AISI 316. • The performance of 3D printed materials lie between WC- based bulk cemented carbides and hardfacings. • The effect of third body and mechanically mixed layer formation during test conditions are discussed. [ABSTRACT FROM AUTHOR]