Search

Characterizing the coseismic slip behaviors of earthquakes could offer a better understanding of regional crustal deformation and future seismic potential assessments. On 18 December 2023, an Mw 6.0 earthquake occurred on the Lajishan–Jishishan fault system (LJFS) in the northeastern Tibetan Plateau, causing serious damage and casualties. The seismogenic fault hosting this earthquake is not well constrained, as no surface rupture was identified in the field. To address this issue, in this study, we use Interferometric Synthetic Aperture Radar (InSAR) data to investigate the coseismic surface deformation of this earthquake and invert both ascending and descending line-of-sight observations to probe the seismogenic fault and its slip characteristics. The InSAR observations show up to ~6 cm surface uplift caused by the Jishishan earthquake, which is consistent with the thrust-dominated focal mechanism. A Bayesian-based dislocation modeling indicates that two fault models, with eastern and western dip orientations, could reasonably fit the InSAR observations. By calculating the coseismic Coulomb failure stress changes (∆CFS) induced by both fault models, we find that the east-dipping fault scenario could reasonably explain the aftershock distributions under the framework of stress triggering, while the west-dipping fault scenario produced a negative ∆CFS in the region of dense aftershocks. Integrating regional geological structures, we suggest that the seismogenic fault of the Jishishan earthquake, which strikes NNE with a dip of 56° to the east, may be either the Jishishan western margin fault or a secondary buried branch. The optimal finite-fault slip modeling shows that the coseismic slip was dominated by reverse slip and confined to a depth range between ~5 and 15 km. The released seismic moment is 1.61 × 1018 N·m, which is equivalent to an Mw 6.07 earthquake. While the Jishishan earthquake ruptured a fault segment of approximately 20 km, it only released a small part of the seismic moment that was accumulated along the 220 km long Lajishan–Jishishan fault system. The remaining segments of the Lajishan–Jishishan fault system still have the capability to generate moderate-to-large earthquakes in the future. [ABSTRACT FROM AUTHOR]

Deformation along a subway rail network is related to the safe operation of the subway and the stability of construction facilities on the surface, making long-term deformation monitoring imperative. Long-term monitoring of surface deformation along the subway network and statistical analysis of the overall deformation situation are lacking in China. Therefore, targeting 35 Chinese cities whose subway mileage exceeds 50 km, we extracted their surface deformation along subway networks between 2018 and 2022, using spaceborne synthetic aperture radar (SAR) interferometry (InSAR) technology and Sentinel-1 satellite data. We verified the results with the continuous global navigation satellite system (GNSS) stations' data and found that the root mean square error (RMSE) of the InSAR results was 3.75 mm/year. Statistical analysis showed that ground subsidence along the subways was more prominent in Beijing, Tianjin, and other areas in the North China Plain, namely Kunming (which is dominated by karst landforms), as well as Shanghai, Guangzhou, Qingdao, and other coastal cities. In addition, an analysis revealed that the severity of surface subsidence correlated positively with a city's gross domestic product (GDP) with a Pearson correlation of 0.787, since the higher the GDP, the more frequent the construction and maintenance of subway, and the more commuters there are, which in turn exacerbates the disturbance to the surface. Additionally, the type of land cover also affects the ground deformation. Our findings provide a reference for constructing, operating, and maintaining the urban subway systems in China. [ABSTRACT FROM AUTHOR]

Accurate retrieval of forest above ground biomass (AGB) based on full-polarization synthetic aperture radar (PolSAR) data is still challenging for complex surface regions with fluctuating terrain. In this study, the three-step process of radiometric terrain correction (RTC), which includes polarization orientation angle correction (POAC), effective scattering area correction (ESAC), and angular variation effect correction (AVEC), is adopted as the technical framework. In the ESAC stage, a normalized correction factor is introduced based on local incidence angle and radar incidence angle to achieve accurate correction of PolSAR data information and improve the inversion accuracy of forest AGB. In order to verify the validity and robustness of this research method, the full-polarization SAR data of ALOS-2 and the ground measured AGB data collected in the Saihanba research area in 2020 were used for experiments. Our findings revealed that in the ESAC phase, the introduction of the normalized correction factor can effectively eliminate the ESA phenomenon and improve the correlation coefficients of the backscatter coefficient and AGB. Taking the data of 25 July 2020 as an example, ESAC increases the correlation coefficients between AGB and the backscattering coefficients of HH, HV, and VV polarization channels by 0.343, 0.296, and 0.382, respectively. In addition, the RTC process has strong robustness in different AGB statistical models and different date PolSAR data. [ABSTRACT FROM AUTHOR]

Ocean salinity is a pivotal aspect of the ocean dynamic environment. Spaceborne L-band radiometers, like SMOS, Aquarius, and SMAP, offer a comprehensive approach to mapping out large-scale ocean salinity patterns. As China prepares for the launch of the Chinese Ocean Salinity and Soil Moisture Mission (COSM), it is essential to delve into the intricacies of radio frequency interference (RFI) detection, localization, and mitigation. The L-band, in particular, is highly susceptible to RFI. COSM will carry not one but two advanced instruments: a 2-D L-band aperture synthesis microwave radiometer (LASMR) and a 1-D L-C-K band microwave imager combined active and passive (MICAP). This article delves into the current state of RFI research, particularly in recent years, and introduces a fusion method that integrates MICAP and LASMR for more accurate RFI detection, localization, and mitigation. This fusion method relies on an algorithm that constructs localization and intensity objective functions based on the principle of least squares. By optimizing these functions, we can pinpoint the precise location and intensity of RFI. The resulting minimum mitigation residual offers a blueprint for achieving optimal RFI detection, localization, and mitigation. The experimental results, achieved in a controlled anechoic chamber, confirm that this fusion method—when weighted by variance—boosts detection accuracy, refines localization precision, and minimizes residual mitigation errors compared with standalone MICAP or LASMR techniques. [ABSTRACT FROM AUTHOR]

Long-distance water transfer is a critical engineering measure to rectify disparities in water resource distribution across regions. The effective operation and safety of such projects are paramount to their success, as localized issues can have cascading consequences, potentially disrupting the entire network. Conventional ground-based monitoring methods have limitations in measuring the deformation of large-scale structures. In this paper, InSAR is employed to monitor the deformation of the Shuangwangcheng (SWC) Reservoir, which features a long embankment dam as part of the South-to-North Water Diversion Project in China. We utilize data from both Sentinel-1 and TerraSAR-X satellites to derive 7-year deformation. Results reveal that the entire dam experiences continuous subsidence, with the maximum deformation in the line-of-sight direction measuring ~160 mm. While minor differential settlements are noted in different sections of the dam, the gradient is not significant due to the dam's substantial length. The InSAR deformation results from multiple geometries demonstrate good consistency, with the highest correlation observed between the Sentinel-1 ascending and descending datasets, exceeding 0.9. Validation against the GNSS observations of the three sites on the SWC Dam shows the accuracy of InSAR displacements is ~8 mm. Water level changes do impact deformation, but consolidation settlement appears to be the primary controlling factor during the monitoring period. This study underscores the potential of InSAR in long-distance water transfer projects and highlights that spatially continuous deformation is the most significant advantage. [ABSTRACT FROM AUTHOR]

With the rapid economic development in China, coal resources are being exploited greatly, which easily causes geological disasters due to surface subsidence. Fast and accurate surface subsidence monitoring and forecasting in mining regions are important references to analyze surface variation laws and disaster warning. However, differential interferometric synthetic aperture radar (D-InSAR) in mine surface monitoring is highly sensitive to spatiotemporal baseline and atmospheric delay. In addition, traditional machine learning algorithms have complicated network structures and difficulties determining parameters. Small baseline subsets InSAR (SBAS-InSAR) and extreme learning machine (ELM) dynamic prediction were combined for corresponding experimental studies to address these problems. On the basis of SBAS-InSAR, surface subsidence monitoring data in mining areas in Pingdingshan City, China, were collected, and a comparative analysis of D-InSAR monitoring data was performed, which verified the validity of SBAS-InSAR monitoring. On the basis of SBAS-InSAR data, a prediction model was built by ELM. The model results were compared with the prediction results of back propagation (BP) neural network and support vector machine (SVM) through root mean square error (RMSE) and mean relative error (MRE). Results demonstrate that the surface subsidence prediction of SBAS-InSAR in the monitoring mining area can reach millimeter accuracy. The MRE values of ELM, BP, and SVM prediction are maintained within 2%, 5%, and 8%, and the RMSE values are less than 3 mm, 7 mm, and 10 mm, respectively, thereby indicating that ELM prediction has high accuracy and reliability. This study provides an important evidence for safe production and scientific disaster prevention and reduction in mining areas. [ABSTRACT FROM AUTHOR]

In order to alleviate the conflict between populations and land resource, Tianjin adopted multi-phase reclamation projects to the formed large-scale artificial reclamation land. The reclamation areas, however, are prone to subsidence, which poses a significant threat to infrastructure as well as the safety and assets of the residents. The SBAS-InSAR was used to acquire surface deformation of Tianjin Binhai New Area from January 2017 to December 2022, analyze in depth the response relationship between land subsidence, reclamation project time, and land-use type. There is a strong correlation between surface deformation and reclamation time. Severe land subsidence occurred over newly reclaimed areas. In the offshore direction, the deformation values of the Nangang Industrial Zone, the Lingang Industrial Zone, and Hangu Harbor were −98 mm to −890 mm, 45 mm to −580 mm, and −140 mm to −290 mm, respectively. Significant differences in deformation were detected among different land-use types where reclamation projects were completed in the same time. Subsidence was positively correlated with surface load; in areas with higher surface loads, the surface settlement was also more severe. The average surface settlement for the heavy shipyard, with 67 grain storage tanks and 27 grain storage tanks, road, and bare land were −201 mm, −166 mm, −107 mm, −64 mm, and −43 mm, respectively. This study reveals significant differences of surface deformation in the reclamation completed at different times, and determines that the load is the main driving factor of settlement difference in the reclamation land completed at the same time. This has important guiding significance for preventing and controlling geological disasters in the reclamation area and later development planning. [ABSTRACT FROM AUTHOR]

Landslides frequently occur in the mountainous area of southwest China, resulting in infrastructure damage, as well as a loss of life and property. The use of interferometric synthetic aperture radar (InSAR) technology has become increasingly popular due to its wide coverage, high precision, and efficiency in identifying potential landslides in steep mountainous regions to mitigate risks. This study focused on the Mao County region in China and utilized a small baseline subset of InSAR (SBAS−InSAR) technology with Sentinel-1 and ALOS-2 data to identify the potential landslides and analyze their applicability. To ensure accuracy, the findings were verified using optical image and field surveys. Additionally, a comparative analysis was performed on C-band and L-band SAR data to examine differences in the coherence, geometric distortion, and displacement results, revealing that the L-band has clear advantages in the coherence, suitable observation coverage, and displacement results, while C-band can detect relatively slight displacements. This study aimed to determine the applicability of different SAR satellites for early landslide identification in steep mountainous areas, which can serve as a technical reference for selecting appropriate SAR data and enhancing InSAR identification abilities for potential landslides in the future. [ABSTRACT FROM AUTHOR]

The Chinese-French Oceanography SATellite (CFOSAT) jointly developed by the Chinese National Space Agency (CNSA) and the Centre National d'Etudes Spatiales (CNES) of France carries a wave spectrometer (Surface Waves Investigation and Monitoring, SWIM). SWIM has one nadir and five off-nadir beams to measure ocean surface waves. These near-nadir beams range from 0° to 10° at an interval of 2°. In this work, we investigated the performance of wave parameters derived from wave spectra measured by SWIM at off-nadir beams during the period 2020 to December 2022, e.g., incidence angles of 6°, 8° and 10°, which were collocated with the wave simulated by Simulating Waves Nearshore (SWAN). The validation of SWAN-simulated significant wave heights (SWHs) against National Data Buoy Center (NDBC) buoys of National Oceanic and Atmospheric Administration (NOAA) exhibited a 0.42 m root mean square error (RMSE) in the SWH. Our results revealed a RMSE of 1.02 m for the SWIM-measured SWH in the East Pacific Ocean compared with the SWH simulated by SWAN, as well as a 0.79 correlation coefficient (Cor) and a 1.17 squared error (Err) for the wave spectrum at an incidence angle of 10°, which are better than those (i.e., the RMSEs were > 1.1 m with Cors < 0.76 and Errs > 1.2) achieved at other incidence angles of SWH up to 14 m. This analysis indicates that the SWIM product is a relevant resource for wave monitoring over global seas. The collocated wave retrievals for more than 300 cases from Gaofen-3 (GF-3) synthetic aperture radar (SAR) images in China Seas were also used to verify the accuracy of SWIM-measured wave spectra. The energy of the SWIM-measured wave spectra represented by SWH was found to decrease with an increasing incidence angle in a case study. Moreover, the SWIM-measured wave spectra were most consistent with the SAR-derived wave spectra at an incidence angle of 10°, yielding a 0.77 Cor and 1.98 Err between SAR-derived and SWIM wave spectra under regular sea state conditions (SWH < 2 m). The error analysis indicates that the difference in SWH between SWIM at an incidence angle of 10° and SWAN has an increasing tendency with the growth in sea surface wind and sea state and it stabilizes to be 0.6 m at SWH > 4 m; however, the current and sea level have less influence on the uncertainties of the SWIM product. [ABSTRACT FROM AUTHOR]

Monitoring mine activities can help management track the status of mineral resource exploration and mine rehabilitation. It is crucial to the sustainable development of the mining industry and the protection of the geological environment in mining areas. To monitor the mining activities of shallow surface outcrops in the arid and semi-arid regions of northwest China, this paper proposes a remote sensing monitoring approach of mining activities based on deep learning and integrated interferometric synthetic aperture radar technique. This approach uses the DeepLabV3-ResNet model to identify and extract the spatial location of the mine patches and then uses object-oriented analysis and spatial analysis methods to optimize the mine patch boundaries. SBAS-InSAR technique is used to obtain the time-series deformation information of the mine patches and is combined with the multi-temporal optical imagery to analyze the mining activities in the study area. The proposed approach has a recognition accuracy of 95.80% for the identification and extraction of mine patches, with an F1-score of 0.727 at the pixel level, and the average area similarity for all patches is 0.78 at the object-oriented level. The proposed approach possesses the capability to analyze mining activities, indicating promising prospects for engineering applications. It provides a reference for monitoring mining activities using multisource satellite remote sensing. [ABSTRACT FROM AUTHOR]

Paddy rice is the second-largest grain crop in China and plays an important role in ensuring global food security. However, there is no high-resolution map of rice covering all of China. This study developed a new rice-mapping method by combining optical and synthetic aperture radar (SAR) images in cloudy areas based on the time-weighted dynamic time warping (TWDTW) method and produced distribution maps of single-season rice in 21 provincial administrative regions of China from 2017 to 2022 at a 10 or 20 m resolution. The accuracy was examined using 108 195 survey samples and county-level statistical data. On average, the user's, producer's, and overall accuracy values over all investigated provincial administrative regions were 73.08 %, 82.81 %, and 85.23 %, respectively. Compared with the statistical data from 2017 to 2019, the distribution maps explained 83 % of the spatial variation of county-level planting areas on average. The distribution maps can be obtained at 10.57760/sciencedb.06963 (Shen et al., 2023). [ABSTRACT FROM AUTHOR]

Most dams in China have been operating for a long time and are products of the economic and technical limitations at the time of construction. Due to decades of aging engineering and ancillary problems, these reservoirs pose great threats to the safety of local people and the development of the surrounding economy. In this study, the surface deformation information for the Banqiao Reservoir is monitored with the small baseline subset–synthetic aperture radar interferometry (SBAS-InSAR) method using 80 Sentinel-1A images acquired from 3 January 2020 to 20 August 2022. Additionally, ground measurements from the BeiDou ground-based deformation monitoring stations were collected to validate the InSAR results. Based on the InSAR results, the spatiotemporal deformation features of the dam were analyzed in detail. The results show that the deformation in most areas, including the dam in the study area, is relatively stable, and the regional deformation velocity of the Banqiao Reservoir dam and other hydraulic engineering facilities varies between −1 mm/y and −4 mm/y. The Ru River area has a relatively obvious subsidence trend, and the maximum subsidence velocity reaches 30 mm/y. The InSAR monitoring results are consistent with the change trend in the BeiDou ground-based deformation measurement results. The monitoring results for the reservoir dam area provide a reference for local sustainable development and geological disaster prevention. [ABSTRACT FROM AUTHOR]

The accurate prediction of surface subsidence induced by coal mining is critical to safeguarding the environment and resources. However, the precision of current prediction models is often restricted by the lack of pertinent data or imprecise model parameters. To overcome these limitations, this study proposes an approach to predicting mine subsidence that leverages Interferometric Synthetic Aperture Radar (InSAR) technology and the long short-term memory network (LSTM). The proposed approach utilizes small baseline multiple-master high-coherent target (SBMHCT) interferometric synthetic aperture radar technology to monitor the mine surface and applies the long short-term memory (LSTM) algorithm to construct the prediction model. The Shigouyi coalfield in Ningxia Province, China was chosen as a study area, and time series ground subsidence data were obtained based on Sentinel-1A data from 9 March 2015 to 7 June 2016. To evaluate the proposed approach, the prediction accuracies of LSTM and Support Vector Regression (SVR) were compared. The results show that the proposed approach could accurately predict mine subsidence, with maximum absolute errors of less than 2 cm and maximum relative errors of less than 6%. The findings demonstrate that combining InSAR technology with the LSTM algorithm is an effective and robust approach for predicting mine subsidence. [ABSTRACT FROM AUTHOR]

Interferometric synthetic aperture radar (InSAR) has developed rapidly over the past years and is considered as an important method for surface deformation monitoring, benefiting from growing data quantities and improving data quality. However, the handing of SAR big data poses significant challenges for related algorithms and pipeline, particularly in large-scale SAR data processing. In addition, InSAR algorithms are highly complex, and their task dependencies are intricate. There is a lack of efficient optimization models and task scheduling for InSAR pipeline. In this paper, we design parallel time-series InSAR processing models based on multi-thread technology for high efficiency in processing InSAR big data. These models concentrate on parallelizing critical algorithms that have high complexity, with a focus on deconstructing two computationally intensive algorithms through loop unrolling. Our parallel models have shown a significant improvement of 10–20 times in performance. We have also developed a parallel optimization tool, Simultaneous Task Automatic Runtime (STAR), which utilizes a data flow optimization strategy with thread pool technology to address the problem of low CPU utilization resulting from multiple modules and task dependencies in the InSAR processing pipeline. STAR provides a data-driven pipeline and enables concurrent execution of multiple tasks, with greater flexibility to keep the CPU busy and further improve CPU utilization through predetermined task flow. Additionally, a supercomputing-based system has been constructed for processing massive InSAR scientific big data and providing technical support for nationwide surface deformation measurement, in accordance with the framework of time series InSAR data processing. Using this system, we processed InSAR data with the volumes of 500 TB and 700 TB in 5 and 7 days, respectively. Finally we generated two maps of land surface deformation all over China. [ABSTRACT FROM AUTHOR]

Health monitoring is important for densely distributed urban infrastructures, particularly in cities undergoing rapid economic progress. Permanent scatterer interferometry (PSI) is an advanced remote sensing observation technique that is commonly used in urban infrastructure monitoring. However, the rapid construction of infrastructures may easily cause a loss of coherence for radar interferometry, inducing a low density of effective permanent scatterer (PS) points, which is the main limitation of PSI. In order to address these problems, a novel time-series synthetic aperture radar interferometry (InSAR) process based on the adaptive window homogeneous pixel selection and phase optimization (AWHPSPO) algorithm and thermal expansion linear model (TELM) is proposed. Firstly, for homogeneous point selection, information on both the time-series intensity and deformation phases is considered, which can compensate for the defects of insufficient homogeneous samples and low phase quality in traditional distributed scatterer interferometric synthetic aperture radar (DS-InSAR) processing. Secondly, the physical, thermal expansion component, which reflects the material properties of the infrastructures, is introduced into the traditional linear model, which can more rationally reflect the temporal evolution of deformation variation, and the thermal expansion coefficients can be estimated simultaneously with the deformation parameters. In order to verify our proposed algorithm, the Orange Island area in Changsha City, China, was selected as the study area in this experiment. Three years of its historical time-series deformation fields and thermal expansion coefficients were regenerated. With the use of high-resolution TerraSAR-X radar satellite images, a maximum accumulated settlement of 12.3 mm and a minor uplift of 8.2 mm were detected. Crossvalidation with small baseline subset interferometric synthetic aperture radar (SBAS-InSAR) results using Sentinel 1A data proved the reliability of AWHPSPO. The proposed algorithm can provide a reference for the control of the health and safety of urban infrastructures. [ABSTRACT FROM AUTHOR]

Paddy rice is the second-largest grain crop in China and plays an important role in ensuring global food security. However, there is no high-resolution map of rice covering all of China. This study developed a new rice mapping method by combining optical and synthetic aperture radar (SAR) images in cloudy areas based on the time-weighted dynamic time warping (TWDTW) method and produced distribution maps of single-season rice in 21 provincial administrative regions of China from 2017 to 2022 at 10 or 20-m resolution. The accuracy was examined by using 108195 survey samples and countylevel statistical data. On average, the user's, producer's, and overall accuracy over all investigated provincial administrative regions were 73.08 %, 82.81 %, and 85.23 %, respectively. Compared with the statistical data from 2017 to 2019, the distribution map explained 83 % of the spatial variation of county-level planting areas on average. The distribution maps can be obtained at https://doi.org/10.57760/sciencedb.06963 (Shen et al., 2023). [ABSTRACT FROM AUTHOR]

Green macroalgae bloom (GMB), with the dominant species of Ulva prolifera, has regularly occurred since 2007 along the China coast. Although disaster prevention and control achieved favorable results in 2020, the satellite-observed GMB annual maximum coverage (AMC) rebounded sharply in 2021 to an unprecedented level. The reasons for this rebound and the significant interannual variability over past 15 years are still open questions. Here, by using long-term time-series (2007–2022) optical and Synthetic Aperture Radar satellite observations (1000+ scenes), meteorological data and water quality statistics, the mechanism analysis was performed by exploring effects from natural factors and human activities. Two key determinants for AMC are successfully identified from numerous potential factors which are the macroalgae distribution in a key area (the Subei Shoal) during a critical period (from April to May 20) and the nutrient availability. Furthermore, by using these two parameters, a novel model for AMC prediction (R2 = 0.87, p < 0.01) is proposed and independently validated, which can reasonably explain the significant interannual variability (2014–2021) and agree well with the latest observation in 2022 (percentage difference 12%). Finally, suggestions are proposed for future disaster prevention and alleviation. This work may aid future bloom prediction and management measure optimization. [ABSTRACT FROM AUTHOR]

Because the penetration depth of electromagnetic waves in forests is large in the longer wavelength band, most traditional forest height estimation methods are carried out using polarimetric interferometry synthetic aperture radar (PolInSAR) data of the L or P band, and the estimation method is a three-stage method based on the random volume over ground (RVoG) model. For X-band electromagnetic waves, the penetration depth of radar waves in forests is limited, so the traditional forest height estimation method is no longer applicable. In view of the above problems, in this paper we propose a new forest height estimation strategy for airborne X-band PolInSAR data. Firstly, the sub-view interferometric SAR pairs obtained via frequency segmentation (FS) in the Doppler domain are used to extend the polarimetric interferometry coherence coefficient (PolInCC) range of the original SAR image under different polarization states, so as to obtain the accurate ground phase. For the determination of the effective volume coherence coefficient (VCC), part of the fitting line of the extended-range PolInCC distribution that is intercepted by the fixed extinction coherence coefficient curve (FECCC) of the fixed range is averaged to obtain the accurate effective VCC. Finally, the high-precision forest canopy height in the X-band is estimated using the effective VCC with the ground phase removed in the look-up table (LUT). The effectiveness of the proposed method was verified using airborne-measured data obtained in Shaanxi Province, China. The comparison was carried out using different strategies, in which we substituted one step of the process with the conventional method. The results indicated that our new strategy could reduce the root mean square error (RMSE) of the predicted canopy height vastly to 1.02 m, with a lower estimation height error of 12.86%. [ABSTRACT FROM AUTHOR]

Model-based incoherent polarimetric decomposition is a frequently used technique to analyze multilook data of polarimetric synthetic aperture radars (POLSARs). The purpose of this study is to analyze and compare different model-based incoherent polarimetric decomposition algorithms from the polarimetric information change aspect. For the input of a model-based incoherent polarimetric decomposition algorithm, polarimetric entropy was used to represent the polarimetric information of a coherency matrix. For the output of a model-based incoherent polarimetric decomposition algorithm, there are usually several decomposed components. To quantitatively represent their total polarimetric information, a new concept, generalized polarimetric entropy, was proposed which generalized the concept of polarimetric entropy based on the information entropy additivity of information theory. Generalized polarimetric entropy consists of two parts named as polarimetric power entropy and polarimetric residual entropy, respectively. Polarimetric power entropy describes the distribution status of the Span values of all decomposed components. Polarimetric residual entropy represents the residual randomness of all decomposed components. With the three new concepts, eight model-based incoherent polarimetric decomposition algorithms were compared and analyzed. Two real POLSAR images, respectively, derived by the E-SAR airborne system of Germany and the GF-3 satellite of China were used for the experiments. Experimental results had illustrated several useful conclusions. [ABSTRACT FROM AUTHOR]

Tropical cyclone (TC) vortex structure can be estimated from wind radii (34, 50, and 64 kt). Accurate wind radii are essential for assessing the impact range of TCs. Combining observations from active and passive microwave remote sensing instruments can provide long-time series data for monitoring changes in TC wind structure. Here, the evolution of the wind radii for Typhoon In-fa (2021), from its genesis to its first landfall, is evaluated using data from spaceborne microwave radiometers and synthetic aperture radars (SARs). Our results show that the retrieved wind radii are relatively close to those from the Joint Typhoon Warning Center (JTWC), the coastal automatic weather stations in China, and the advanced scatterometer. The time series for the wind radii show significant increasing trends during the lifecycle of In-fa and a massive vortex structure before In-fa made landfall. The average wind radii observed before landfall are all likely in the 90th percentile of the 2001–2021 JTWC historical wind radii records, indicating that the vortex structure is extraordinarily large before In-fa made landfall and represents a historical extreme. The extremely large vortex structure may be attributable to the interaction between In-fa and an extremely strong monsoon gyre. [Display omitted] • Wind radii for Typhoon In-fa (2021) are evaluated by multiple spaceborne microwave radiometers and SARs. • The retrieved wind radii are close to those from JTWC, AWSs in China, and ASCAT. • The significant increasing trends of wind radii and a massive vortex structure before landfall are revealed. [ABSTRACT FROM AUTHOR]

Ground-based synthetic aperture radar (GBSAR) is a powerful tool used in monitoring structures, such as bridges and dams. However, despite the extremely short range of GBSAR interferometry, the atmosphere effects cannot be neglected. The permanent scatterer technique is an effective operational tool that utilizes a long series of SAR data and detects information with high accuracy. An algorithm based on the permanent scatterer technique is developed in accordance with the phase model used in GBSAR interferometry. In this study, atmospheric correction is carried out on a real campaign (Geheyan Dam, China). The atmosphere effects created using this method, which utilizes SAR data, can be reduced effectively compared to when plumb line data are used. [ABSTRACT FROM AUTHOR]

MDT recovery over coastal regions is challenging, as the mean sea surface (MSS) and geoid/quasi-geoid models are of low quality. The altimetry satellites equipped with the synthetic aperture radar (SAR) altimeters provide more accurate sea surface heights than traditional ones close to the coast. We investigate the role of using the SAR-based MSS in coastal MDT recovery, and the effects introduced by the SAR altimetry data are quantified and assessed. We model MDTs based on the multivariate objective analysis, where the MSS and the recently released satellite-only global geopotential model are combined. The numerical experiments over the coast of Japan and southeastern China show that the use of the SAR-based MSS improves the local MDT. The root mean square (RMS) of the misfits between MDT-modeled with SAR altimetry data and the ocean data is lower than that derived from MDT computed without SAR data—by a magnitude of 4–8 mm. Moreover, the geostrophic velocities derived from MDT modeled with the SAR altimetry data have better fits with buoy data than those derived from MDT modeled without SAR data. In total, our studies highlight the use of SAR altimetry data in coastal MDT recovery. [ABSTRACT FROM AUTHOR]

Abstract: In this paper, we used the available algorithm for soil moisture estimation over LOPEX05 (the Loess Plateau land surface process Experiment (2005)) area. The available algorithm used ENVISAT/ASAR AP mode VV polarization observational data at a low incidence angle and ground measured soil moistures. The ground measurements were performed in the summer of the 2005 during the LOPEX05 field campaign. The validated results indicate that an average difference between the soil moistures estimated from the microwave remote sensing and ground measurements is less than 0.02cm3/cm3, with a RMS error of 2.0%, and a maximum less than 0.04cm3/cm3. The algorithm was applied to the surface soil moisture mapping later. The results show that this algorithm is suitable for monitoring soil moisture information of the agricultural fields over the Chinese Loess Plateau, when ground land cover situation and the resolution of imagery data are taken into account. However, we also find that there are large differences over the steep slope region, the edge of mesa. The results are not acceptable for surface soil moisture estimation in these regions. Thus, the surface soil moisture retrieval in the steep slope region of the Loess Plateau need to be further investigated in the future. [Copyright &y& Elsevier]

The accuracy and applications of synthetic aperture radar interferometry (InSAR) are severely suppressed by tropospheric error. Numerical Weather Models (NWMs) and GPS-derived tropospheric delays have been widely used to correct the tropospheric error considering their complete spatial coverage or high accuracy. However, few studies focus on the fusion of both NWMs and GPS for the tropospheric error correction. In this study, we used the Weather Research and Forecasting (WRF) to obtain NWMs with a higher spatial-temporal resolution of 3 km and 20 s from both ERAI (79 km and 6 h) and ERA5 (0.25° and 1 h). After that, we utilized the WRF Data Assimilation (WRFDA) system to assimilate the GPS ZTD into these enhanced NWMs and generate merged NWMs products. The tropospheric correction effectiveness from different NWMs products was evaluated in a case in the Pearl River Delta region of China. The results showed that all the NWMs products could correct the stratified component in the interferogram but could not mitigate the turbulence well, even after improving the spatial-temporal resolution. As for the trend component, the merged NWMs products showed obvious superiority over other products. From the statistics perspective, the stdev of the interferogram decreased further over 20% by the merged NWMs products than other products when using both ERAI and ERA5, indicating the significant effectiveness of GPS ZTD assimilation. [ABSTRACT FROM AUTHOR]

This work investigated the large-scale ground deformations threatening the Northern Urumqi district, China, which are connected to groundwater exploitation and the seasonal freeze–thaw cycles that characterize this frozen region. Ground deformations can be well captured by satellite data using a multi-temporal interferometric synthetic aperture radar (Mt-InSAR) approach. The accuracy of the achievable ground deformation products (e.g., mean displacement time series and related ground displacement time series) critically depends on the number and quality of the selected interferograms. This paper presents a straightforward interferogram selection algorithm that can be applied to identify an optimal network of small baseline (SB) interferograms. The selected SB interferograms are then used to produce ground deformation products using the well-known small baseline subset (SBAS) Mt-InSAR algorithm. The developed interferogram selection algorithm (ISA) permits the selection of the group of SB data pairs that minimize the relative error of the mean ground deformation velocity. Experiments were carried out using a group of 102 Sentinel-1B SAR data collected from 12 April 2017 to 29 October 2020. This research study shows that the investigated farmland region is characterized by a maximum ground deformation rate of about 120 mm/year. Periodic groundwater overexploitation, coupled with irrigation and freeze–thaw phases, is also responsible for seasonal (one-year) ground displacement signals, with oscillation amplitudes up to 120 mm in the zones of maximum displacement. [ABSTRACT FROM AUTHOR]

Earth Observation (EO) data is a critical information source for mapping and monitoring water resources over large inaccessible regions where hydrological in-situ networks are sparse. In this paper, we present a simple yet robust method for fusing optical and Synthetic Aperture Radar (SAR) data for mapping surface water dynamics over mainland China. This method uses a multivariate logistic regression model to estimate monthly surface water extent over a four-year period (2017 to 2020) from the combined usages of Sentinel-1, Sentinel-2 and Landsat-8 imagery. Multi-seasonal high-resolution images from the Chinese Gaofen satellites are used as a reference for an independent validation showing a high degree of agreement (overall accuracy 94%) across a diversity of climatic and physiographic regions demonstrating potential scalability beyond China. Through inter-comparison with similar global scale products, this paper further shows how this new mapping technique provides improved spatio-temporal characterization of inland water bodies, and for better capturing smaller water bodies (< 0.81 ha in size). The relevance of the results is discussed, and we find this new enhanced monitoring approach has the potential to advance the use of Earth observation for water resource management, planning and reporting. [ABSTRACT FROM AUTHOR]

Classification based on polarimetric synthetic aperture radar (PolSAR) images is an emerging technology, and recent years have seen the introduction of various classification methods that have been proven to be effective to identify typical features of many terrain types. Among the many regions of the study, the Hunshandake Sandy Land in Inner Mongolia, China stands out for its vast area of sandy land, variety of ground objects, and intricate structure, with more irregular characteristics than conventional land cover. Accounting for the particular surface features of the Hunshandake Sandy Land, an unsupervised classification method based on new decomposition and large-scale spectral clustering with superpixels (ND-LSC) is proposed in this study. Firstly, the polarization scattering parameters are extracted through a new decomposition, rather than other decomposition approaches, which gives rise to more accurate feature vector estimate. Secondly, a large-scale spectral clustering is applied as appropriate to meet the massive land and complex terrain. More specifically, this involves a beginning sub-step of superpixels generation via the Adaptive Simple Linear Iterative Clustering (ASLIC) algorithm when the feature vector combined with the spatial coordinate information are employed as input, and subsequently a sub-step of representative points selection as well as bipartite graph formation, followed by the spectral clustering algorithm to complete the classification task. Finally, testing and analysis are conducted on the RADARSAT-2 fully PolSAR dataset acquired over the Hunshandake Sandy Land in 2016. Both qualitative and quantitative experiments compared with several classification methods are conducted to show that proposed method can significantly improve performance on classification. [ABSTRACT FROM AUTHOR]

Mining subsidence is time-dependent and highly nonlinear, especially in the Loess Plateau region in Northwestern China. As a consequence, and mainly in building agglomerations, the structures can be damaged severely during or after underground extraction, with risks to human life. In this paper, we propose an approach based on a combination of a differential interferometric synthetic aperture radar (DInSAR) technique and a support vector machine (SVM) regression algorithm optimized by grid search (GS-SVR) to predict mining subsidence in a timely and cost-efficient manner. We consider five Advanced Land Observing Satellite (ALOS)/Phased Array type L-band Synthetic Aperture Radar (PALSAR) images encompassing the Dafosi coal mine area in Binxian and Changwu counties, Shaanxi Province. The results show that the subsidence predicted by the proposed InSAR and GS-SVR approach is consistent with the Global Positioning System (GPS) measurements. The maximum absolute errors are less than 3.1 cm and the maximum relative errors are less than 14%. The proposed approach combining DInSAR with GS-SVR technology can predict mining subsidence on the Loess Plateau of China with a high level of accuracy. This research may also help to provide disaster warnings. [ABSTRACT FROM AUTHOR]

Unsupervised change detection approaches, which are relatively straightforward and easy to implement and interpret, and which require no human intervention, are widely used in change detection. Polarimetric synthetic aperture radar (PolSAR), which has an all-weather response capability with increased polarimetric information, is a key tool for change detection. However, for PolSAR data, inadequate evaluation of the difference image (DI) map makes the threshold-based algorithms incompatible with the true distribution model, which causes the change detection results to be ineffective and inaccurate. In this paper, to solve these problems, we focus on the generation of the DI map and the selection of the optimal threshold. An omnibus test statistic is used to generate the DI map from multi-temporal PolSAR images, and an improved Kittler and Illingworth algorithm based on either Weibull or gamma distribution is used to obtain the optimal threshold for generating the change detection map. Multi-temporal PolSAR data obtained by the Radarsat-2 sensor over Wuhan in China are used to verify the efficiency of the proposed method. The experimental results using our approach obtained the best performance in East Lake and Yanxi Lake regions with false alarm rates of 1.59% and 1.80%, total errors of 2.73% and 4.33%, overall accuracy of 97.27% and 95.67%, and Kappa coefficients of 0.6486 and 0.6275, respectively. Our results demonstrated that the proposed method is more suitable than the other compared methods for multi-temporal PolSAR data, and it can obtain both effective and accurate results. [ABSTRACT FROM AUTHOR]

Landslide is the second most frequent geological disaster after earthquake, which causes a large number of casualties and economic losses every year. China frequently experiences devastating landslides in mountainous areas. Interferometric Synthetic Aperture Radar (InSAR) technology has great potential for detecting potentially unstable landslides across wide areas and can monitor surface displacement of a single landslide. However traditional time series InSAR technology such as persistent scatterer interferometry (PSI) and small-baseline subset (SBAS) cannot identify enough points in mountainous areas because of dense vegetation and steep terrain. In order to improve the accuracy of landslide hazard detection and the reliability of landslide deformation monitoring in areas lacking high coherence stability point targets, this study proposes an adaptive distributed scatterer interferometric synthetic aperture radar (ADS-InSAR) method based on the spatiotemporal coherence of the distributed scatterer (DS), which automatically adjusts its detection threshold to improve the spatial distribution density and reliability of DS detection in the landslide area. After time series network modeling and deformation calculation of the ADS target, the displacement deformation of the landslide area can be accurately extracted. Shuibuya Town in Enshi Prefecture, Hubei Province, China, was used as a case study, along with 18 Sentinal-1A images acquired from March 2016 to April 2017. The ADS-InSAR method was used to obtain regional deformation data. The deformation time series was combined with hydrometeorological and related data to analyze landslide deformation. The results show that the ADS-InSAR method can effectively improve the density of DS distribution, successfully detect existing ancient landslide groups and determine multiple potential landslide areas, enabling early warning for landslide hazards. This study verifies the reliability and accuracy of ADS-InSAR for landslide disaster prevention and mitigation. [ABSTRACT FROM AUTHOR]