Search

The cold spray deposition process has gained interest as a promising technique for producing metallic coatings on polymers and composite materials thank to its low working temperatures. However, poor adhesion of metallic particles on polymeric substrates and the brittle nature of these materials lead to generation of cracks under the impact of the sprayed particles, limiting its application to polymeric matrix composite. The interposition of an intermediate metallic layer over the thermoset composite to be coated has been claimed to improve the adhesion of the sprayed particles and the formation of a stable link between the metal coating and the underlying polymer panel. The present work discusses a methodology that integrates the manufacturing of glass reinforced epoxy panels having functionalized surface and the subsequent production of a dense metallic layer by cold spray. Pure copper and titanium metallic powders, having spherical and irregular shape respectively, were placed on the top of the stack of dry glass fiber fabrics. Resin infusion process was then applied to impregnate the glass fabrics providing the simultaneous functionalization of the composite panel. In order to assess the effectiveness of the produced substrate, and of the proposed procedure, metallic coatings have been finally deposited on manufactured composite panels by means of a low-pressure cold spray facility. Regardless the spraying condition (namely gas temperature, stand-off distance, sprayed particles), copper samples showed a remarkable erosion of functionalized layer after cold spray process with pronounced damages of the composite substrate. On the other hand, effective depositions have been observed on titanium samples under specific combination of process parameters.

Cold spray (CS) is an emerging coating technology that makes use of a converging/diverging nozzle, a high pressure and a heated gas source to create a high‐velocity gas flow. Coating deposition occurs at relatively low temperatures compared to other spray technologies, therefore the sprayed particles remaining in the solid-state. The process can produce dense coatings when the process parameters are optimized. Despite the incredible advantages of CS and the established knowledge of CS considering metal substrates, some questions like the bonding mechanism and the adhesion/cohesion strength of the coating with polymeric substrates remain an open research topic. In this paper, a metal coating (AlSi10Mg) was deposited on a plate in polypropylene by cold spray in order to increase the properties of the surface. Metallic particles, in the range of 20-40 µm, were injected into gas flow and propelled to supersonic velocities. Polymers require a deposition technique in which the substrate remains at relatively low temperatures during the whole process in order to avoid plastic deformation or degradation. Determination of the mechanical properties of thin films on substrates by indentation has always been difficult because of the influence of the substrate on the measured properties. In order to evaluate the local properties of the deposited coating, microindentation tests and DMA were carried out. In particular hardness values by microindentation tests and values of elastic modulus by DMA were calculated.

The integration of metals and polymers in the same component to couple the best properties and advantages of both these classes of materials can be useful for engineering applications. In this scenario, the aim of this paper is to integrate additive manufacturing of composites with cold spray deposition of metal particles: in particular, 3D-printed carbon fibre-reinforced plastics (CFRP) panels were coated with aluminium particles to couple the lightweight and high mechanical properties of CFRP with high wear resistance and hardness of metals. CFRP panels have been produced by using the Fused Filament Fabrication (FFF) technology, then the panels have been coated with aluminium particles by using a low pressure cold spray facility. Panels with various stratification sequences have been produced to investigate the feasibility of the process and to highlight the influence of the lay-up strategy on the whole process; the parameters of the cold spray process have been also optimized to ensure an effective deposition. Adhesion tests, distortion measurements, cross-section observations and surface coverage measurements have been chosen as response outputs to evaluate the effectiveness of the process and to assess the influence of the process parameters. The integration between FFF of CFRPs and cold spray deposition of aluminium particles has been proved, values of surface coverage close to 100% and good values of adhesion strength (close to 4 MPa) have been achieved; moreover, the presence of the fibres, giving a higher stiffness to the substrate, avoids the occurrence of distortion phenomena during the deposition. It was also proved that the printing parameters influence the deposition: an increase in the infill density from 30% to 50% leads to an increase in the adhesion strength up to 40%. In summary, the results obtained proved the feasibility of the process and allowed to enucleate directions of future research.

Cold spray deposition, which can be framed in the wider family of additive manufacturing, is a manufacturing technique that is able to produce coatings on diverse types of substrates through the deposition of feedstock powder. As a low-temperature process, cold spray represents a potential solution for the metallization of temperature-sensitive materials, i.e. polymers and polymer matrix composites. The study of the cold spray technology for the metallization of polymers is still in its early stage, and the deposition mechanisms of metals on polymer-based materials are not thoroughly understood yet. On these premises, a review on this topic is needed to systematically depict the actual state of the art and to provide a reliable and well-organized overview discussing all the theories arisen in these years. In summary, this review aims: i) to collect all the available literature and enucleate the most discussed and interesting points (the most prevailing theories regarding the bonding mechanisms, the influence of the different process parameters and the main characteristics of cold-sprayed coating), providing a reliable and well-organized state of the art; ii) to define the open questions and to delineate the directions of future work.

Cold spray (CS) is a low-temperature process that can be used for the metallization of temperature-sensitive materials, such as polymers or polymer matrix composites, so coupling the lightweight of polymers with the wear resistance, physical properties and hardness of metals. The study of the cold spray of metal particles applied to polymers is still in its early stage and the deposition mechanisms underlying the process are not thoroughly understood yet. Moreover, numerical studies of cold spray of metal-to-polymer are almost completely absent in literature. Therefore, aiming to fulfill this gap of knowledge, the scope of this work is to develop a numerical FE model capable of predicting the impact and the adhesion of a micron size metallic particle onto a polymeric substrate. The results from the model were compared with the experimental outcomes found in literature to establish the effectiveness of the model that was used as a powerful tool to better understand the bonding mechanisms and all the related phenomena ruling the CS process of metal-to-polymer.

In this work, the manufacturing through cold gas dynamic spray (cold spray or CS) of metallic composite coatings of Al-Al2O3 on organic composite substrates with thermoplastic PLA matrix and hemp fibers was studied. Alumina powders, with a mean diameter of 50 μm, were used blended with aluminum powders in three different weight concentration percentages (0, 15, 20, and 45%) as feedstock material in order to highlight and discuss the variations of the coating surface properties depending on the alumina percentage. The coatings were produced by using a low-pressure cold spray equipment. A detailed experimental campaign, including microstructural observations and confocal microscopy, was carried out to study the structure of the coatings. Moreover, the tribological behavior of the coatings was studied through both scratch test and pin-on-disk test. The experiments showed that a small addition of alumina improves the compactness of the coating and its resistance to scratch and wear behavior.

International audience; Composite materials are widely used as main parts and structural components in different fields, especially for automotive and military applications. Although these materials supply different advantages comparing to the metals, their implementation in engineering applications is limited due to low electrical and thermal properties and low resistance to erosion. To enhance these above-mentioned properties, the metallization of composite materials by creating a thin metal film on their surface can be achieved. Among different coating deposition techniques, Cold Spray appears to be the most suitable one for the metallization of temperature-sensitive materials such as polymers and composites with a thermoplastic matrix. This process relies on kinetic energy for the formation of the coating rather than on thermal energy and consequent erosion and degradation of the polymer-based composite can be avoided. In the last years, a new method to produce composite materials, as known as Fused Filament Fabrication (FFF), has been developed for industrial applications. This technique consists of a 3D printing process that involves the thermal extrusion of thermoplastic polymer and fibers in the form of filaments from a heated mobile nozzle. The implementation of this new technique is leading to the manufacturing of customized composite materials for the cold spray application. In the presented experimental campaign, Onyx material is used as a substrate. This material is made of Nylon, a thermoplastic matrix, and chopped carbon fibers randomly dispersed in it. Aluminum powders were cold sprayed on the Onyx substrate with a low-pressure cold spray (LPCS) system. This study aims to investigate the possibility of the metalizing 3D-printed composite material by cold spray technology. For this purpose, optical and microscopical analyses are carried out. Based on the results, the feasibility of the process and the influence of the morphology of the substrate are discussed, and optimal spraying conditions are proposed.

Polymer matrix composites are finding never-ending widespread uses in the last decades, one recent tendency is to metallize their surface to further widen their field of application. Cold-spray deposition is one of the most promising techniques that can be adopted to this aim. Cold-spray deposition on polymers is in its early stage and more experimental work is required to fully understand the phenomena ruling the deposition. In this paper, the results of nanoindentation measurements on cold-spray coatings on various substrates will be presented and discussed. Polypropylene was used as matrix while carbon and glass fibers have been used as reinforcement, both steel and aluminum have been used as feedstock material for the cold-spray deposition. Nanoindentations tests have been then carried out on all the different samples, the influence of the fibers and of the powders sprayed on the behavior of the coatings is discussed in light of the experimental outcomes.

Metallization is a common strategy employed to enhance the electrical and thermal conductivity of polymer matrix composite materials. Nevertheless, metallic deposition on polymer-based materials is challenging due to the inherent limitations related to high temperature exposure of the substrate. In this article, a new technique for the manufacturing of composite laminates and the subsequent metallization by cold spraying of metallic powder is presented. The composite manufacturing route is based on the production of thermoplastic-thermoset hybrid substrates and consisted of two main stages: in the first stage the partial impregnation of a reinforcement textile by a thermoplastic film was promoted by hot pressing compaction. Afterwards, the prepared lamina was vacuum bagged with other reinforcing layers and impregnated by the thermoset catalyzed resin by a vacuum infusion process. Finally, the thermoset and thermoplastic layers were co-cured to increase the adhesion of the substrate with the thermoplastic film. The metallization of composite laminate was obtained through the cold spraying technique, depositing powders on the thermoplastic surface layer. The effect of processing parameters on the coating deposition, quality and microstructure was reported and discussed.

The low-velocity impact behaviour of novel composite structures, made of a polymer matrix composite with a superficial 3D printed metallic layer, was studied. The metallic layer was produced through cold spray deposition which is a relatively new additive coating technique allowing for the deposition of metallic coatings on thermal-sensitive substrates, such as the polymeric materials. Micron-sized aluminium particles were used to metallise the surface of basalt-nylon 6 (PA6) laminates manufactured by the compression moulding technique. Three different energy levels (10 J, 20 J, 30 J) were set for the impact tests. The results obtained pointed out the beneficial contributions of the metallic coating on the energy absorbing modes of the polymeric substrates; the positive effects on the damage mechanisms as well as the crack propagation were detected by plastic deformation analyses and ultrasonic damage controls.