Search

A compact random fiber laser based on a short artificial Rayleigh reflector and heavily-doped Er fibers (custom-made and commercial as a reference) has been proposed, characterized and optimized in terms of efficiency, linewidth and noise level. A 10-cm artificial Rayleigh reflector with mean scattering level of +41.3 dB/mm relative to the natural Rayleigh scattering of the host fiber and low insertion loss level (~0.05 dB/cm at 1535 nm) was fabricated using a femtosecond direct writing technique. Its implementation as a distributed output mirror in a half-open cavity of a 980-nm diode pumped Er-doped fiber laser results in random lasing at 1535 nm in single- and few-mode regimes with power up to 100 mW, slope efficiency up to 16.5%, and signal-to-noise ratio up to 60 dB. A single-frequency regime with ~10 KHz linewidth was observed at output power up to 2.5 mW. Tunability potential of such random lasers is also demonstrated.

An all-fiber 4-core Yb-doped laser with a cavity formed by fiber Bragg gratings directly inscribed in each core with femtosecond laser pulses and 4% Fresnel reflection from the output fiber end face is demonstrated. It has been shown that the diameter of the active fiber winding significantly affects the power distribution between the cores, since it affects both the pump power distribution and the cross-coupling between the cores. In particular, with an active fiber winding diameter of 21 cm, the cores behave independently, and the power is distributed almost evenly over all cores. With a winding diameter of 6.5 cm, the lasing is achieved almost exclusively from one core, and a mechanism of that radiation concentration based on bending induced stress in an active multicore fiber is proposed which explains the experimental data. By analyzing the optical and radio-frequency spectra of the output laser radiation, additional details of the 4-core fiber lasing are revealed. In particular, a narrowband (several longitudinal modes) lasing with periodic linear sweeping of central wavelength in time is observed and characterized in the multicore fiber laser, for the first time to our knowledge. It is shown that crosstalk of longitudinal modes arising from different cores is greatly enhanced in the case of a strongly bent fiber.

In this paper, we demonstrate the application of deep neural networks (DNNs) for processing the reflectance spectrum from a fiberoptic temperature sensor composed of densely inscribed fiber bragg gratings (FBG). Such sensors are commonly avoided in practice since close arrangement of short FBGs results in distortion of the spectrum caused by mutual interference between gratings. In our work the temperature sensor contained 50 FBGs with the length of 0.95 mm, edge-to-edge distance of 0.05 mm and arranged in the 1500–1600 nm spectral range. Instead of solving the direct peak detection problem for distorted signal, we applied DNNs to predict temperature distribution from entire reflectance spectrum registered by the sensor. We propose an experimental calibration setup where the dense FBG sensor is located close to an array of sparse FBG sensors. The goal of DNNs is to predict the positions of the reflectance peaks of the reference sparse FBG sensors from the reflectance spectrum of the dense FBG sensor. We show that a convolution neural network is able to predict the positions of FBG reflectance peaks of sparse sensors with mean absolute error of 7.8 pm that is slightly higher than the hardware reused interrogator equal to 5 pm. We believe that dense FBG sensors assisted with DNNs have a high potential to increase spatial resolution and also extend the length of a fiber optical sensors.

The paper presents a novel three-dimensional quasi-continuous shape sensor based on an FBG array inscribed by femtosecond laser pulses into a 7-core optical fiber with a polyimide protective coating. The measured bending sensitivity of individual FBGs ranges from 0.046 nm/m-1 to 0.049 nm/m-1. It is shown that the sensor allows for reconstructing 2- and 3-dimensional shapes with high accuracy. Due to the high value of the core aperture and individual calibration of each FBG we were able to measure the smallest reported bending radii down to 2.6 mm with a record accuracy of ∼1%. Moreover, we investigate the magnitude of the errors of curves reconstruction and errors associated with measurement of curvature radii in the range from 2.6 to 500 mm. The main factors affecting the accuracy of measurements are also discussed. The temperature resistance of both the inscribed FBG structures and of the protective coating, along with the high mechanical strength of the polyimide, makes it possible to use the sensor in harsh environments or in medical and composite material applications.

Narrowband Raman lasing in a polarization-maintaining two-core fiber (TCF) is demonstrated. Femtosecond point-by-point inscription of fiber Bragg gratings (FBGs) in individual cores produces a half-open cavity with random distributed feedback. The laser linewidth in the cavity with a single FBG inscribed in one core of the TCF reduced by similar to 2 times with respect to the cavity with a fiber loop mirror. It is shown that the inscription of two FBGs in different cores leads to the formation of a Michelson-type interferometer, leading to the modulation of generation spectra near threshold. This technique offers new possibilities for spectral filtering or multi-wavelength generation. (C) 2019 Optical Society of America

Raman lasing in a graded-index fiber (GIF) attracts now great deal of attention due to the opportunity to convert high-power multimode laser diode radiation into the Stokes wave with beam quality improvement based on the Raman clean-up effect. Here we report on the cascaded Raman generation of the 2nd Stokes order in the 1.1-km long GIF with 100-μm core directly pumped by 915-nm diodes. In the studied all-fiber scheme, the 1st Stokes order is generated at 950–954 nm in a linear cavity formed at GIF ends by two fiber Bragg gratings (FBGs) securing beam quality improvement from M2 ≈ 30 to M2 ≈ 2.3 due to special transverse structure of FBGs. The 2nd Stokes wave is generated either in linear (two FBGs) or half-open (one FBG) cavity with random distributed feedback via Rayleigh backscattering. Their comparison shows that the random lasing provides better beam quality and higher slope efficiency. Nearly diffraction limited beam (M2 ≈ 1.6) with power up to 27 W at maximum gain (996 nm), and 17 W at the detuned wavelength of 978 nm has been obtained, thus demonstrating that the 2nd-order random lasing in diode-pumped GIF with FBGs provides high-efficiency high-quality beam generation in a broad wavelength range within the Raman gain spectral profile.

Experimental method of temperature and strain discrimination with fiber Bragg gratings (FBGs) sensors embedded in carbon fiber-reinforced plastic is proposed. The method is based on two-fiber technique, when two FBGs inscribed in different fibers with different sensitivities to strain and/or temperature are placed close to each other and act as a single sensing element. The nonlinear polynomial approximation of Bragg wavelength shift as a function of temperature and strain is presented for this method. The FBGs were inscribed with femtosecond laser by point-by-point inscription technique through polymer cladding of the fiber. The comparison of linear and nonlinear approximation accuracies for array of embedded sensors is performed. It is shown that the use of nonlinear approximation gives 1.5–2 times better accuracy. The obtained accuracies of temperature and strain measurements are 2.6–3.8°C and 50–83 μεin temperature and strain range of 30–120°C and 0–400 με, respectively.

In this paper, we present a new method of point-by-point femtosecond inscription of fiber Bragg gratings (FBG) arrays of different configurations in a 7-core spun optical fiber. The possibility of FBGs inscription with predefined periods in individual fiber cores allowed us to realize: 1) longitudinal FBG arrays with identical or variable resonant wavelengths in all side cores, 2) longitudinal FBG arrays inscribed only in the central or in the selected side core, and 3) an FBG array in a transverse cross section of a fiber consisting of an FBG inscribed in the central and three side cores. Based on the proposed method, by enabling the inscription through the acrylate protective coating of the fiber, a vector bend sensor has been created. Implementation of this sensor has shown that bending radii less than 4 mm can be measured with a high precision using a single-channel interrogation scheme.

In this paper, we present the results of thermochemical LIPSS formation on a chromium film with a thickness in the range of 28-350 nm induced by femtosecond laser radiation (λ = 1026 nm, ν = 200 kHz, τ = 232 fs). The period, height, morphology and chemical composition of TLIPSS as a function of the metal film thickness and focusing configuration are investigated. The growth of TLIPSS period from 678 nm to 950 nm with increasing thickness of the film has been explained by a formation of oxides with different stoichiometry composition. So, the CrO2 oxide prevails in the composition for the case of TLIPSS formed on thin films which have the minimal period, whereas Cr2O3 oxide is dominant in the case of TLIPSS formed on thick chromium films which have the maximal period value. The results obtained are in agreement with numerical modeling of a period defined by the interference between an incident radiation and a scattered one from a single oxide ridge with a different chemical composition.

We present the results of comparative numerical study of energy deposition in single shot femtosecond laser inscription for fundamental and second harmonic of Yb-doped fiber laser. We have found that second harmonic is more efficient in absorbing energy which leads to lower inscription threshold. Hence this regime is more attractive for applications in femtosecond laser microfabrication.

We present the results of experimental and theoretical study of an energy absorption of femtosecond laser pulse in fused silica. Fundamental and second harmonics of ytterbium laser were used in experiment while general case was considered theoretically and numerically. More efficient absorption at the second harmonics is confirmed both experimentally and numerically. Quantitative characterization of the theoretical model is performed by fitting key parameters of the absorption process such as cross-section of multi-photon absorption and effective electronic collision and recombination times.

The significant progress in the development of multi-core fibers (MCFs) and the technology of refractive index change by fs- laser radiation [1] in the selective cores of MCF open up possibilities for the creation of new configurations of fiber lasers based on both active MCFs with inscribed fiber Bragg gratings [2] and passive MCFs in Raman lasers with random distributed feedback [3] for high-power laser applications.