Search

In order to obtain analytical gain expression in Brillouin optical Fiber Amplifiers (BFAs), coupled intensity equations describing the interaction of pump and stokes waves must be solved simultaneously. For long optical fibers, although fiber loss is responsible for the pump depletion and nonnegligible effect, for short optical fibers less than 2 km, its effect can be discarded. In this paper, we provide an accurate analytic expression for the BFA gain for fiber lengths less than 2 km by discarding the optical fiber loss and show results of experimental validation.

Room-temperature highly sensitive microbolometers are becoming very attractive in infrared (IR) sensing with the increase in demand for the internet of things (IOT), night vision, and medical imaging. Different techniques, such as building extremely small-scale devices (nanotubes, etc.) or using 2D materials, showed promising results in terms of high sensitivity with the cost of challenges in fabrication and low-noise readout circuit. Here, we propose a new and simple technique on the application of joule heating on a clamped&ndash, clamped beam without adding any complexity. It provides much better uniformity in temperature distribution in comparison to conventional joule heating, and this results in higher thermal stresses on fixed ends. This consequently brings around 60.5&times, improvement in the overall temperature sensitivity according to both theory and COMSOL (multiphysics solver). The sensitivity increased with the increase in the stiffness constant, and it was calculated as 134 N/m for a device with a 60.5&times, improvement. A considerable amount of decrease in the operation temperature (36&times, below 383 K and 47&times, below 428 K) was achieved via a new technique. That&rsquo, s why the proposed solution can be used either to build highly reliable long-term devices or to increase the thermal sensitivity.

Goktas, Hasan/0000-0002-2195-9531 WOS: 000454463000028 A silicon-based light source presents an unreached goal in the field of photonics due to silicon's indirect electronic band structure preventing direct carrier recombination and subsequent photon emission. Here, we utilize inelastically tunneling electrons to demonstrate an electrically driven light emitting silicon-based tunnel junction operating at room temperature. We show that such a junction is a source for plasmons driven by the electrical tunnel current. We find that the emission spectrum is not given by the quantum condition where the emission frequency would be proportional to the applied voltage, but the spectrum is determined by the spectral overlap between the energy-dependent tunnel current and the modal dispersion of the plasmon. By coupling an internal electric field enhancement with an external k-vector matching grating, we were able to demonstrate a 10-fold increase in the internal efficiency and a 40-fold increase in overall quantum efficiency. Such an electron tunneling-based mechanism could lead to a new class of solid-state light sources with unique features such as down-scalability and temporal responses that are significantly shorter than that of light-emitting diodes. Air Force Office of Scientific ResearchUnited States Department of DefenseAir Force Office of Scientific Research (AFOSR) [FA9550-17-1-0377] V.S. is supported by Air Force Office of Scientific Research under the Award FA9550-17-1-0377. We thank Josh Conway for helpful discussions and Ergun Simsek for numerical analysis support.

Goktas, Hasan/0000-0002-2195-9531 WOS: 000424678900006 PubMed: 29400726 We report on an accurate closed-form analytical model for the gain of a Brillouin fiber amplifier that accounts for material loss in the depleted pump regime. We determined the operational model limits with respect to its relevant parameters and pump regimes through both numerical and experimental validation. As such, our results enable accurate performance prediction of Brillouin fiber amplifiers operating in the weak-pump, high-gain, and saturation regimes alike. (C) 2018 Optical Society of America

We present a comprehensive analysis of the technique of Longitudinal-Mode-Filling (LMF) to reduce Stimulated Brillouin Scattering (SBS) limitations in Ytterbium Doped Fibre Amplifiers (YDFA), for the generation of nanosecond, temporally shaped pulses. A basic Master-Oscillator-Power-Amplifier (MOPA) system, comprising an output YDFA with 10 mu m-core active fibre, is experienced for benchmarking purposes. Input pulse-shaping is operated thanks to direct current modulation in highly multimode laser-diode seeds, either based on the use of Distributed Feed-Back (DFB) or of a Fibre Bragg Grating (FBG). These seeds enable wavelength control. We verify the effectiveness of the combination of LMF, with appropriate mode spacing, in combination with natural chirp effects from the seed to control the SBS threshold in a broad range of output energies, from a few to some tens of mu J. These variations are discussed versus all the parameters of the laser system. In accordance with the proposal of a couple of basic principles and with the addition of gain saturation effects along the active fibre, we develop a full-vectorial numerical model. Fine fits between experimental results and theoretical expectations are demonstrated. The only limitation of the technique arises from broadband beating noise, which is analysed thanks to a simplified, but fully representative description to discuss the signal-to-noise ratio of the amplified pulses. This provides efficient tools for application to the design of robust and cost-effective MOPAs, aiming to the generation of finely shaped and energetic nanosecond pulses without the need for any additional electro-optics. (C) 2014 Optical Society of America

Purpose – The purpose of this paper is to present the method of lines (MOL) solution of the stimulated Brillouin scattering (SBS) equations (a system of three first-order hyperbolic partial differential equations (PDEs)), describing the three-wave interaction resulting from a coupling between light and acoustic waves. The system has complex numbers and boundary values. Design/methodology/approach – System of three first-order hyperbolic PDEs are first transformed and then spatially discretized. Superbee flux limiter is proposed to offset numerical damping and dispersion, brought on by the low order approximation of spatial derivatives in the PDEs. In order to increase computational efficiency, the structured structure of the PDE Jacobian matrix is identified and a sparse integration algorithm option of the ordinary differential equation (ODE) solvers is used. The flux limiter based on higher order approximations eliminates numerical oscillation. Examples are presented, and the performance of the Matlab ODE solvers is evaluated by comparison. Findings – This type of solution provides a rapid means of investigating SBS as a tool in fiber optic sensing. Originality/value – To the best of the authors' knowledge, MOL solution is proposed for the first time for the modeling of three-wave interaction in a SBS-based fiber optic sensor.

The spectral and temporal evolution of distributed sensing based on stimulated Brillouin scattering (SBS) in optical fibers for several-nanosecond Stokes pulses is demonstrated by using the method of lines (MOL) solution of the transient SBS equations. A superbee flux limiter is utilized to avoid numerical damping and dispersion that would otherwise be brought on by the approximation of spatial derivatives associated with the partial differential equations (PDEs). In order to increase computational efficiency, an approach is adopted where by the sparse PDE jacobian matrix integrator option of the ODE solver(s) is employed. Simulation examples of SBS-based sensing for fibers containing sections with different Brillouin frequencies are presented. To the best of our knowledge, this MOL solution is proposed for the first time for modeling of the transient SBS equations for nanosecond Stokes pulses with different waveforms in a SBS based fiber optic sensor.

PurposeThe aim of the paper is to demonstrate a fast numerical solution for Raman fiber amplifier equations using proposed guess functions and MATLAB intrinsic properties. MATLAB BVP solvers are addressed for the solution.Design/methodology/approachThe guess functions proposed for the solution of RFA equations using MATLAB BVP solvers are derived from Taylor expansion of pump and signal wave near the boundary to specifically obtain convergence for the initial mesh point. The guess functions increase simulation speed significantly. In order to improve the simulation speed further, vectorization and analytical Jacobians are introduced. Comparisons among bvp4c and bvp5c have been made with respect to total pump power, number of signals, vectorization with/without analytical Jacobians, fiber length, relative tolerance and continuation method. The simulations are performed to determine the effect of the run time on the choice of the number of equally spaced mesh points (N) in the initial guess, and thus optimal N values are found.FindingsMATLAB BVP solvers have been proven to be effective for the numerical solution of RFAs with the proposed guess functions. In particular, with vectorizing, run time reduction is between 2.1 and 5.4 times for bvp4c and between 1.6 and 2.1 times for bvp5c and in addition to vectorizing, with the introduction of the analytical Jacobians, the reduction is between 2.4 and 6.2 times for bvp4c and 1.7 and 2.2 times for bvp5c, respectively, depending on the total pump power between 1,000 mW and 2,000 mW and the number of signals. Also, simulation results show that the efficiency of the solution with proposed guess functions is improved more than six times compared with those of previously reported continuation methods. Results show that the proposed guess functions with the vectorization and analytical Jacobians can be used for the performance evaluation of RFAs for the high power systems/long gain fiber span.Practical implicationsThe robust improvement of the solution proposed in this paper lies in the fact that the derived guess functions for the RFAs are highly effective in the sense that they assist the solver to converge to the solution for any total pump power value in a wide range from 1 to 3,000 mW and for any fiber lengths ranging 1 to 200 km which are used in practical applications. Hence, it is practicable for the performance evaluation of the existing RFA networks.Originality/valueThe novelty of this method is that, starting with the co‐propagating single pump and signal RFA schema, the authors derived the guess function specifically for the initial mesh points rather than using its analytical approximations. Moreover, the solution is generalized for co‐/counter propagating pumps/signals with the curve fitted coefficient(s).

The MATLAB computing environment is a package used extensively throughout industry, research and education by users of a complete range in proficiency. MATLAB provides then an ideal platform to introduce such an item of Boundary Value Problem (BVP) software and indeed, Kierzenka and Shampine (Kierzenka & Shampine, 2001) developed the core BVP Ordinary Differential Equation (ODE) software bvp4c to solve a large class of two-point boundary value problems of the form

Highly accurate closed-form analytical formula, based on the undepleted pump approximation (UPA), is derived for pump, Stokes and the gain of a Brillouin fiber amplifier (BFA) operating in the moderately depleted pump regime. The material loss of the medium, which is a strong effect in optical fibers, is taken into account. To define validity ranges of the solution, the threshold power of BFA is accurately determined. The obtained results are numerically and experimentally validated. The presented analysis can be used to accurately predict the performance of moderate-gain BFAs.