Search

Plasmonic Cu nanoparticles were in-situ grown into a Cu$_2$O semiconductor matrix by using reactive magnetron sputtering and adjusting the amount of oxygen available during the synthesis in order to prevent the oxidation of part of copper atoms landed on the film surface. Varying only the oxygen flowrate (OFR) and using a single Cu target it was possible to observe the evolution in the simultaneous formation of metallic Cu and Cu$_2$O phases for oxygen-poor conditions. Suchformation is accompanied by the development of the surface plasmon band (SPB) corresponding to Cu, as evidenced by UV-Vis spectrophotometry and spectroscopic ellipsometry. The bandgap values of the elaborated composites containing embedded Cu plasmonic nanodomains were lower than the bandgap of single-phased Cu$_2$O films, likely due to the higher defect density associated to the nanocrystalline nature of films, promoted by the presence of metallic Cu. The resistivity of the thin films increased with more oxidative deposition conditions and was associated to an increase in Cu$_2$O/Cu ratio and smaller and more isolated Cu particles, as evidenced by high resolution transmission electron microscopy and X-ray diffraction. Photoconversion devices based on the studied nanocomposites were characterized by I-V and spectral photocurrent measurements, showing an increase in the photocurrent density under light illumination as consequence of the plasmonic particles excitation leading to hot carrier's injection in the nearby ZnO and Cu$_2$O semiconductors., Comment: ACS Applied Electronic Materials, American Chemical Society, 2022

Following the 2nd release of the “Emerging PV reports,” the best achievements in the performance of emerging photovoltaic devices in diverse emerging photovoltaic research subjects are summarized, as reported in peer‐reviewed articles in academic journals since August 2021. Updated graphs, tables, and analyses are provided with several performance parameters, e.g., power conversion efficiency, open‐circuit voltage, short‐circuit current density, fill factor, light utilization efficiency, and stability test energy yield. These parameters are presented as a function of the photovoltaic bandgap energy and the average visible transmittance for each technology and application, and are put into perspective using, e.g., the detailed balance efficiency limit. The 3rd installment of the “Emerging PV reports” extends the scope toward triple junction solar cells.

Emerging photovoltaics (PVs), focuses on a variety of applications complementing large scale electricity generation. For instance, organic, dye-sensitized and some perovskite solar cells are considered in building integration, greenhouses, wearable and indoors, thereby motivating research on flexible, transparent, semitransparent, and multi-junction PVs. Nevertheless, it can be very time consuming to find or develop an up-to-date overview over the state-of-the-art performance for these systems and applications. Two important resources for record research cells efficiencies are the National Renewable Energy Laboratory chart and the efficiency tables compiled biannually by Martin Green and colleagues. Both publications provide an effective coverage over the established technologies, bridging research and industry. An alternative approach is proposed here summarizing the best reports in the diverse research subjects for emerging PVs. Best performance parameters are provided as a function of the photovoltaic bandgap energy for each technology and application, and are put into perspective using, e.g., the Shockley-Queisser limit. In all cases, the reported data correspond to published and/or properly described certified results, with enough details provided for prospective data reproduction. Additionally, the stability test energy yield (STEY) is included as an analysis parameter among state-of-the-art emerging PVs.

Emerging photovoltaics (PVs) focus on a variety of applications complementing large scale electricity generation. Organic, dye-sensitized, and some perovskite solar cells are considered in building integration, greenhouses, wearable, and indoor applications, thereby motivating research on flexible, transparent, semitransparent, and multi-junction PVs. Nevertheless, it can be very time consuming to find or develop an up-to-date overview of the state-of-the-art performance for these systems and applications. Two important resources for recording research cells efficiencies are the National Renewable Energy Laboratory chart and the efficiency tables compiled biannually by Martin Green and colleagues. Both publications provide an effective coverage over the established technologies, bridging research and industry. An alternative approach is proposed here summarizing the best reports in the diverse research subjects for emerging PVs. Best performance parameters are provided as a function of the photovoltaic bandgap energy for each technology and application, and are put into perspective using, e.g., the Shockley-Queisser limit. in all cases, the reported data correspond to published and/or properly described certified results, with enough details provided for prospective data reproduction. Additionally, the stability test energy yield is included as an analysis parameter among state-of-the-art emerging PVs., VDI/VD Innovation + Technik GmbH; SAOT - German Research Foundation (DFG)German Research Foundation (DFG); DFGGerman Research Foundation (DFG)European Commission [INST 90/917-1 FUGG, 182849149, SFB 953]; Energy Conversion Systems-from Materials to Devices [IGK 2495]; grant "ELF-PV-Design and development of solution processed functional materials for the next generations of PV technologies" [44-6521a/20/4]; grant "Solar Factory of the Future" [FKZ 20.2-3410.5-4-5]; SolTech Initiative by the Bavarian State Government; FAPESPFundacao de Amparo a Pesquisa do Estado de Sao Paulo (FAPESP) [2017/11986-5]; ShellRoyal Dutch Shell; ANP (Brazil's National Oil, Natural Gas and Biofuels Agency) through the R&D levy regulation; National Science FoundationNational Science Foundation (NSF) [CBET-1702591]; US Department of Energy, Office of Energy Efficiency and Renewable Energy, Solar Energy Technologies OfficeUnited States Department of Energy (DOE) [34351]; European Research Council under the European Union's Horizon 2020 research and innovation program [742708]; Projekt DEAL, O.A. acknowledges the financial support from the VDI/VD Innovation + Technik GmbH (Project-title: PV-ZUM) and the SAOT funded by the German Research Foundation (DFG) in the framework of the German excellence initiative. C.J.B. acknowledges funding from DFG within INST 90/917-1 FUGG, the SFB 953 (DFG, project no. 182849149) and the IGK 2495 (Energy Conversion Systems-from Materials to Devices). C.J.B. further acknowledges the grants "ELF-PV-Design and development of solution processed functional materials for the next generations of PV technologies" (No. 44-6521a/20/4) and "Solar Factory of the Future" (FKZ 20.2-3410.5-4-5) and the SolTech Initiative by the Bavarian State Government. A.F.N. acknowledges support from FAPESP (Grant 2017/11986-5), Shell and the strategic importance of the support given by ANP (Brazil's National Oil, Natural Gas and Biofuels Agency) through the R&D levy regulation. R.R.L. gratefully acknowledges support from the National Science Foundation under grant CBET-1702591. N.K. acknowledges funding by the US Department of Energy, Office of Energy Efficiency and Renewable Energy, Solar Energy Technologies Office, Agreement Number 34351. J.N. thanks the European Research Council for support under the European Union's Horizon 2020 research and innovation program (grant agreement No 742708).; Open access funding enabled and organized by Projekt DEAL.

Herein we present a process for the in-situ growth of CdS nanoparticles using a pulsed laser irradiation. A Nd-YAG laser was applied to ZnO nanorods previously submerged in an aqueous precursor solution containing cadmium chloride and thiourea. For optimum values of the laser fluence, around 40 mJ/cm2 it was possible to fabricate a highly homogeneous film of CdS nanoparticles covering the ZnO nanorods surface. Cathodoluminescence measurements of the ZnO/CdS structure show the quenching of the ZnO yellow and green luminescence, indicating the ZnO surface defects passivation by CdS nanostructures. Although lasers have been already used for inducing growth in solution, this work presents new evidence of in-situ growth on the surface of nanostructured materials. The laser based technique presented is simple, easy to implement, scalable and it could be applied in the fabrication of nanostructured solar cells and other devices.