Search

Objectives: To evaluate the effect of ozone and two common denture cleansers on the surface hardness and bond strength of a silicone-based soft liner to acrylic denture base material. Materials and Methods: Sixty cylindrical specimens were fabricated using heat-cured poly-methyl methacrylate denture base resin. Three millimeters of the material was ground from the midsection and filled with the soft liner. The resilient liner specimens (n=40) used for the hardness test were 10 mm in diameter and 5 mm in height. Cylindrical and disc-shaped samples were randomly divided into four groups (37°C distilled water, Corega® tablets, 0.5% sodium hypochlorite (NaOCl), and a home ozone generator). To simulate six months of denture cleansing clinically, samples were placed in their cleanser once a day for six months according to the manufacturer’s instructions. All cylindrical specimens were placed under tension until failure in a universal testing machine at a crosshead speed of 5 mm/minute. For disc-shaped samples, hardness was measured using a Shore-A durometer. The results were analyzed using Kruskal-Wallis test, analysis of variance (ANOVA), and Tukey's post hoc test. Results: The mean tensile bond strength was not significantly different among the studied groups (P>0.05). The mean hardness in the ozone and Corega tablet groups was significantly lower than that of the control and NaOCl groups (P

Background: The type of housing retaining material may affect the bond strength of the housing to denture base resin. The aim of this in vitro study was to evaluate the bond strength of locator housing attached to polymethyl methacrylate (PMMA) denture base resin secured with different retaining materials. Materials and Methods: In this in vitro study Forty-four PMMA blocks (10 mm × 15 mm × 15 mm) were prepared with a central cylindrical canal inside to allow the insertion of locator housings. The prepared specimens were then randomly divided into four groups (n = 11). Each group received one of the following retaining materials for housing insertion: Auto-polymerized acrylic resin (APAR), auto-polymerized composite resin (Quick up), application of alloy primer on titanium housing plus Quick up (AL-Quick), and heat-polymerized acrylic resin (HPAR). The specimens were thermocycled 5000 times between 5°C and 55°C, followed by 1000 cycles of vertical insertion separation on the locator abutment. A push-out force was applied on the flat back surface of the housing after which the failure and shear bond strength values were calculated. The data were analyzed using one way-ANOVA and Games-Howell test (α = 0.05). Results: HPAR group had significantly higher shear bond strength values compared to the other groups (P < 0.05). No significant differences were found among the other remaining material groups (P > 0.05). Conclusion: Inserting of locator housing using HPAR resulted in higher bond strength between housing and denture base resin. The application of alloy primer did not improve the bond strength of locator housing which was retained with “Quick up”.

This study attempted to investigate the effect of sandblasting and H2O2 treatments on the microshear bond strength of two commercially available resin cements. A total of 90 cube-shaped specimens of commercially pure titanium (cp-Ti) were divided into two groups of Panavia and MHA cements (n = 45). Samples of the Panavia group were randomly divided into three subgroups of 15 samples, including subgroups (no treatment, aluminum oxide sandblasting, and immersion in 35% hydrogen peroxide solution with halogen light). Once the treatment was completed, Panavia V5 was applied on the cp-Ti surface by a Tygon tube. The 45 specimens of the MHA cement group were randomly divided into three subgroups (n = 15) similarly to the Panavia group. Then, the MHA was applied on the surface of cp-Ti. A universal testing machine was used to measure and examine the microshear bond strength of cement to cp-Ti subsequent to the step of thermocycling. According to results, in the Panavia cement group, the SBS of sandblasting treatment was significantly higher than that of the H2O2 treatment subgroup (p < 0.05), which displayed a significantly higher SBS than that of the no-treatment subgroup (p < 0.001). In regard to the MHA group, the SBS of the H2O2 treatment subgroup was significantly lower than that of the sandblasting treatment subgroup (p < 0.001), whereas there were no significant differences between the SBS of the no treatment and H2O2 treatment subgroups (p = 0.35). Considering the comparison between Panavia and MHA cases, there were no significant differences observed among the no-treatment subgroups (p = 0.34), as well as the sandblasting treatment subgroups (p = 0.67), while the SBS of the H2O2 treatment subgroup in Panavia cement was higher than that of the H2O2 subgroup in MHA cement (p < 0.001). In conclusion, in both Panavia V5 and MHA cements, sandblasting treatment could improve the bond strength between the titanium surface. However, H2O2 treatment proved to be capable of enhancing the bond strength of Panavia V5 cement without causing any positive effects on the bond strength of MHA cement.

Introduction: Detachment of denture teeth from denture base is one of the most common reasons for costly denture repairs .This study aimed at evaluating the bond strength of an acrylic denture tooth to polyamide injection-molded thermoplastic denture base material compared with three conventional polymethylmethacrylate (PMMA) denture base resins. Materials and Method: A total of 40 acrylic denture molar teeth were randomly allocated into four groups (n=10) of heat-polymerized (HP), Auto-polymerized (AP), Injection molded (IM) and Polyamide thermoplastic (PT). All denture base/acrylic teeth combinations underwent 5000 thermal cycles (5-55◦C).Samples were subjected to shear bond strength test by a universal testing machine with a 1 mm/min crosshead speed .Data were analyzed using ANOVA and Tukey’s tests(α=0.05). Results: Mean ±SD of shear bond strength values were (MPa) 4.82±1.21, 4.52±1.67, 3.7±0.84 and 4.13±2.21 for groups HP, AP, IM and PT respectively. No significant difference was found among the experimental groups (P=0.429). Conclusion: Polyamide thermoplastic denture base resin was similar to conventional PMMA denture base materials in terms of bond strength to artificial denture teeth.

Introduction: While using an implant-supported removable partial prosthesis, the implant abutments should be parallel to one another along the path of insertion. If the implants and their attachments are placed vertically on a similar occlusal plane, not only is the retention improved, the prosthesis will also be maintained for a longer period. Case Report: A 65-year-old male patient referred to the School of Dentistry in Mashhad, Iran with complaints of discomfort with the removable partial dentures for his lower mandible. Due to the lack of parallelism in the supporting implants, prefabricated ball abutment could not be used. As a result, a customized ball abutment was fabricated in order to correct the non-parallelism of the implants. Conclusion: Using UCLA abutments could be a cost-efficient approach for the correction of misaligned implant abutments in implant-supported overdentures.

Introduction: A dental impression is a negative imprint of an oral structure that can be used to produce a positive cast of a patient's teeth as a permanent record. The accuracy of the impression affects the accuracy of the cast, and a precise impression is needed in order to create prosthesis with optimal fitting. Minimization of misfit is an important aim in prosthesis science and dental implants. The aim of this study was to evaluate the effects of the materials and techniques used to take an impression on the vertical misfit of implant-supported, screw-retained, three-unit bridges. Materials and Methods: The principal model used was an acrylic block with two ITI implants. A 1.5-mm abutment was attached to fixtures with torque of 25 N.cm. A base-metal framework was built on the abutment in the acrylic block. The abutments of the acrylic model were unscrewed and fixture-level impressions were made. The impression techniques included open/closed-tray techniques and the impression materials were polyether and polyvinyl siloxane. Forty acrylic custom trays were built for each impression. The marginal gap in the framework at three points (buccal, lingual, and distal) was measured using an optical microscope with ×250. Results: It is demonstrated that in all 360 evaluated samples, the mean vertical misfit in polyether samples of molar and premolar teeth was significantly lower than in polyvinyl siloxane (P < 0.001 and P = 0.017, respectively) in all three locations of the molar and lingual premolar examined (buccal, lingual, and distal), the mean vertical misfit of the polyether samples was significantly lower than those of polyvinyl siloxane (P < 0.01). On the other hand, although the mean vertical misfit using the open-tray technique in the molar teeth was significantly lower than with the closed-tray method (P = 0.002), no statistical difference was seen between the open-tray and closed-tray technique in general (P = 0.87). Conclusion: Within the limitations of this study, the following conclusions can be drawn: The impression method had no effect on marginal discrepancy of 3-unit screw retained fixed partial dentures. A higher marginal accuracy was obtained using polyether impression material compared to polyvinyl siloxane.

Background: The final position of the abutment changes with the amount of tightening torque. This could eventually lead to loss of passivity and marginal misfit of prostheses. The aim of this study was to evaluate the effect of three different tightening torques on the marginal adaptation of 3-unit cement-retained implant-supported fixed dental prostheses (FDPs). Materials and Methods: Two implants (Straumann) were inserted in an acrylic block so that one of the implants was placed vertically and the other at a 15° vertical angle. A straight abutment and a 15° angulated abutment were connected to the vertically and obliquely installed implants, respectively, so that the two abutments were parallel. Then, 10 cement-retained FDPs were waxed and cast. Abutments were tightened with 10, 20, and 35 Ncm torques, respectively. Following each tightening torque, FDPs were luted on respective abutments with temporary cement. The marginal adaptation of the retainers was evaluated using stereomicroscope. FDPs were then removed from the abutments and were sectioned at the connector sites. The retainers were luted again on their respective abutments. Luting procedures and marginal adaptation measurement were repeated. Data were analyzed by ANOVA and least significant difference tests (α = 0.05). After cutting the FDP connectors, the independent samples t-test was used to compare misfit values (α = 0.05). Results: Following 10, 20, and 35 Ncm tightening torques, the marginal discrepancy of the retainers of FDPs significantly increased (P < 0.05). There was no significant difference between the marginal discrepancies of these two retainers (P > 0.05). The marginal gap values of angulated abutment retainers (ANRs) were significantly higher than those of the straight abutment after cutting the connectors (P = 0.026). Conclusion: Within the limitations of this study, the marginal misfit of cement-retained FDPs increased continuously when the tightening torque increased. After cutting the connectors, the marginal misfit of the ANRs was higher than those of the straight abutment retainers.

Background: Color stability of acrylic resin is one of the most important feature for denture wearers. Many patients use detergent solutions to remove denture stains. The purpose of this study was to evaluate color stability and surface roughness of two common acrylic resins in different detergent and tea solutions. Materials and Methods: 112 acrylic resin blocks of Meliodent and Acropars (each 56 blocks) were divided into seven groups of different treatment: 1% sodium hypochlorite for 10 min a day for 1 month (H10m), 1% sodium hypochlorite for 8 hours a day for 1 week (H&h), Correga tabs solution for 8 hours a day for 1 month (C&H), tea bag for 2 hours a day for 1 month (T2 h), tea bag for 2 hours a day then 10 min in 1% sodium hypochlorite for 1 month (T-H), tea bag for 2 hours then 8 hours in the Correga tab solution a day for 1 month (T-C), and finally distilled water for 1 month as a control group (con). After specimen′s treatment, color (CIE Lab) and surface roughness (Ra, µm) of samples were measured. The results were analyzed by analysis of variance (ANOVA), followed by Tukey′s HSD and Dunnett T3. Results: Group T2h exhibited a significant (P

Background: Accurate impression making is an essential prerequisite for achieving a passive fit between the implant and the superstructure. The aim of this in vitro study was to compare the three-dimensional accuracy of open-tray and three closed-tray impression techniques. Materials and Methods: Three acrylic resin mandibular master models with four parallel implants were used: Biohorizons (BIO), Straumann tissue-level (STL), and Straumann bone-level (SBL). Forty-two putty/wash polyvinyl siloxane impressions of the models were made using open-tray and closed-tray techniques. Closed-tray impressions were made using snap-on (STL model), transfer coping (TC) (BIO model) and TC plus plastic cap (TC-Cap) (SBL model). The impressions were poured with type IV stone, and the positional accuracy of the implant analog heads in each dimension (x, y and z axes), and the linear displacement (ΔR) were evaluated using a coordinate measuring machine. Data were analyzed using ANOVA and post-hoc Tukey tests (α = 0.05). Results: The ΔR values of the snap-on technique were significantly lower than those of TC and TC-Cap techniques (P < 0.001). No significant differences were found between closed and open impression techniques for STL in Δx, Δy, Δz and ΔR values (P = 0.444, P = 0.181, P = 0.835 and P = 0.911, respectively). Conclusion: Considering the limitations of this study, the snap-on implant-level impression technique resulted in more three-dimensional accuracy than TC and TC-Cap, but it was similar to the open-tray technique.

Introduction: Some clinicians use a handheld screw driver instead of a torque wrench to definitively tighten abutment screws. The aim of this study was to compare the removal torque of one-piece and two-piece abutments tightened with a handheld driver and a torque control ratchet. Methods: 40 ITI implants were placed in acrylic blocks and divided into 4 groups. In groups one and two, 10 ITI one-piece abutments (Solid®) and in groups three and four, 10 ITI two-piece abutments (Synocta®) were placed on the implants. In groups one and three abutments were tightened by 5 experienced males and 5 experienced females using a handheld driver. In groups two and four abutments were tightened using a torque wrench with torque values of 10, 20 and 35 N.cm. Insertion torque and removal torque values of the abutments were measured with a digital torque meter. Results: The insertion torque values (ITVs) of males in both abutments were significantly higher than those of females. ITVs in both Solid® and Synocta® abutments tightened with a handheld screwdriver were similar to the torque of 20 N.cm in the torque wrench. Removal torque values (RTVs) of solid® abutments were higher than those of synocta® abutments. Conclusion: The one- piece abutments (solid®) showed higher RTVs than the two-piece abutments (synocta®). Hand driver does not produce sufficient preload force for the final tightening of the abutment

Introduction: Reconstruction of intraoral soft tissue defects is important in restoring function and esthetic. In large defects, there will be demand for regional pedicle flaps or free flaps. Hard palate separates nasal and oral cavities. Due to the small surface area between flap and remaining palate after surgical resections, optimal blood supply of the flaps for hard palate reconstructions are needed. This article demonstrates immediate reconstruction of two edentulous hemimaxillectomy patients with submental artery Island flap and brief review of this flap discussed.