Search

Abstract: Among specific sensitive materials synthesized for chemical sensor development, cobalt corrole have shown attractive capabilities for CO detection . In this paper, we investigate the possibility to exploit such materials to develop surface acoustic wave (SAW)-based sensors. We actually demonstrate that SAW devices using delay line configuration allow investigating the molecular recognition occurring in non-conductive sensing layers of cobalt corroles. We have monitored phase variations of SAW devices versus various CO concentrations. Moreover, a specific testing setup has been developed to precisely dose CO at low concentrations, to avoid any CO leakage in the environment, to systematically control environmental parameters and to allow regeneration of the trapping sites of CO. [Copyright &y& Elsevier]

Surface acoustic wave (SAW) transducers propagating shear waves are compatible with sensing chemical compounds in a liquid phase. However, if the liquid surrounding the sensor possesses a higher permittivity than the piezoelectric substrate, then the interdigitated electrodes for converting the incoming electromagnetic wave to acoustic waves are susceptible to capacitive short-circuiting, leading to excessive insertion losses. By using high-permittivity lithium tantalate oxide (LTO), we demonstrate chemical sensing in water without the need for dedicated microfluidic packaging. Nevertheless, the gravimetric sensitivity of these package-less transmission Love-mode delay lines remains comparable to that of low-permittivity quartz when appropriately tuning the guiding layer of thin film to confine energy to the surface in a Love mode. We extend the transmission line gravimetric sensitivity measurement to a reflective delay line geometry for passive transducers that can be wirelessly probed. For instance, ground-penetrating radar (GPR) can be used for subsurface sensing, here targeting water pollution detection, operating in the 100-500-MHz range. This center frequency was selected as a tradeoff between penetration depth (lower frequency) and antenna size (smaller at higher frequency). Nonspecific binding of proteins detection is shown in the context of biosensing applications.

The detection of organophosphates, a wide class of pesticides, in water-solution has a huge impact in environmental monitoring. Acoustic transducers are used to design passive wireless sensors for the direct detection of pesticides in water-solution by using tailored polymers as sensitive layers. We demonstrate by combining analytical chemistry tools that organophosphate molecules strongly alter polymer layers widely used in acoustic sensors in the presence of water. This chemical degradation can limit the use of these polymers in detection of organophosphates in water-solution.

The fast and efficient detection of foodborne pathogens is a societal priority, given the large number of food-poisoning outbreaks, and a scientific and technological challenge, given the need to detect as little as 1 viable cell in 25 gr of food. Here, we present the first approach that achieves the above goal, thanks to the use of a micro/nano-technology and the detection capability of acoustic wave sensors. Starting from 1 Salmonella cell in 25 ml of milk, we employ immuno-magnetic beads to capture cells after only 3 h of pre-enrichment and subsequently demonstrate efficient DNA amplification using the Loop Mediated Isothermal Amplification method (LAMP) and acoustic detection in an integrated platform, within an additional ½ h. The demonstrated 4 h sample-to-analysis time comes as a huge improvement to the current need of few days to obtain the same result. In addition, the work presents the first reported Lab-on-Chip platform that comprises an acoustic device as the sensing element, exhibiting impressive analytical features, namely, an acoustic limit of detection of 2 cells/μl or 3 aM of the DNA target and ability to detect in a label-free manner dsDNA amplicons in impure samples. The use of food samples together with the incorporation of the necessary pre-enrichment step and ability for multiple analysis with an internal control, make the proposed methodology highly relevant to real-world applications. Moreover, the work suggests that acoustic wave devices can be used as an attractive alternative to electrochemical sensors in integrated platforms for applications in food safety and the point-of-care diagnostics., (Copyright © 2018. Published by Elsevier B.V.)

Passive wireless transducers are used as sensors, probed by a RADAR system. A simple way to separate the returning signal from the clutter is to delay the response, so that the clutter decays before the echoes are received. This can be achieved by introducing a fixed delay in the sensor design. Acoustic wave transducers are ideally suited as cooperative targets for passive, wireless sensing. The incoming electromagnetic pulse is converted into an acoustic wave, propagated on the sensor substrate surface, and reflected as an electromagnetic echo. According to a known law, the acoustic wave propagation velocity depends on the physical quantity under investigation, which is then measured as an echo delay. Both conversions between electromagnetic and acoustic waves are based on the piezoelectric property of the substrate of which the sensor is made. Investigating underground sensing, we address the problems of using GPR (Ground-Penetrating RADAR) for probing cooperative targets. The GPR is a good candidate for this application because it provides an electromagnetic source and receiver, as well as echo recording tools. Instead of designing dedicated electronics, we choose a commercially available, reliable and rugged instrument. The measurement range depends on parameters like antenna radiation pattern, radio spectrum matching between GPR and the target, antenna-sensor impedance matching and the transfer function of the target. We demonstrate measurements at depths ranging from centimeters to circa 1 m in a sandbox. In our application, clutter rejection requires delays between the emitted pulse and echoes to be longer than in the regular use of the GPR for geophysical measurements. This delay, and the accuracy needed for sensing, challenge the GPR internal time base. In the GPR units we used, the drift turns out to be incompatible with the targeted application. The available documentation of other models and brands suggests that this is a rather general limitation. We solved the problem by replacing the analog ramp generator defining the time base with a fully digital solution, whose time accuracy and stability relies on a quartz oscillator. The resulting stability is acceptable for sub-surface cooperative sensor measurement., Competing Interests: The authors declare no conflict of interest. The founding sponsors had no role in the design of the study; in the collection, analyses or interpretation of data; in the writing of the manuscript; nor in the decision to publish the results.