Search

Abstract Among different types of transformerless photovoltaic inverters, multi‐level inverters based on switched‐capacitors (SC) are the burning topic of recent decades due to their potential advantages, such as, single source requirement, voltage boosting capability, and high power density. However, for a seven level output voltage, a conventional SC based inverter architecture uses more than two units of SC, a large amount of power switches, which then lead to capacitor voltage balancing problems. This paper presents a seven‐level switched‐capacitor transformerless inverter (SCTI), which is structured with only two SC units, ten power switches, and a single DC source. The proposed SCTI ensures voltage boosting capability, self‐voltage balancing, and low power semiconductor losses. Apart from these, a modified sinusoidal pulse width modulation (MSPWM) is also proposed in this work, which guarantees better thermal performance and low inverter output voltage THD for the proposed SCTI. The proposed SCTI along with the MSPWM is simulated in MATLAB/Simulink and PLECS computer simulation environments. A reduced scale laboratory prototype is also built and tested to ensure the feasibility of the proposed SCTI.

Research into solar photovoltaic (PV) fed grid-tied multilevel inverters (MLIs) has increased in recent years due to their distinct features compared to two-level voltage source inverters (VSIs). However, maintaining the power quality of MLIs is a challenging problem that encompasses the reduction of total harmonic distortion (THD), dc-link voltage imbalance issues, power loss reduction and thermal stress mitigation; which are significantly affected by the applied pulse width modulation (PWM) technique. In order to tackle the above mentioned power quality problems, this work presents a modified hybrid PWM technique which combines a modified modulating signal with a modified carrier signal. The comparison between the proposed and the existing PWM techniques is performed under different conditions and using a wide range of modulation index variations. A grid-tied three-phase three-level T-type neutral point clamped (NPC) inverter is adopted for the power quality assessment. The proposed hybrid PWM offers 25.57% output line voltage THD and 11.8 V peak-to-peak dc-link capacitor voltage difference which are lower than existing PWM techniques. Additionally, by reducing the switching and conduction losses of the power switches, the proposed hybrid PWM technique offers lower thermal stress than existing PWM techniques. The comparative analysis between the existing and the proposed hybrid PWM technique is carried out using MATLAB/Simulink and PLECS simulation environments. The proposed hybrid PWM technique is further validated using a reduced scale prototype developed in our research laboratory.

Transformerless grid-connected inverters have attained a lot of research interest in renewable energy interface applications, due to certain promising properties like greater efficiency, light weight, affordable price, and tolerable power density. Among various types of transformerless grid-tied photovoltaic (PV) inverters, multilevel inverters (MLIs) are mostly popular due to their ability to transmit reactive power, small filter size for reducing total harmonic distortion (THD) and their common-ground (CG) configuration to mitigate the detrimental leakage current due to the parasitic capacitances of the PV array. Again, among different types of MLIs for PV systems, switched-capacitor (SC) based multilevel inverter topologies are the burning topic in current decades due to their single source requirements for producing multilevel output voltage. However, for mostly used single-phase five-level inverters, most of the existing SC based topology requires at least two SCs for power conversion. In this paper, a five-level transformerless inverter based on a single SC is proposed, requiring only seven switches, no diode, a single capacitor, and one dc voltage source. The proposed transformerless MLI also has auto-boosting capability. Notably, the number of power switches operating at high frequency is limited to three, which lowers down the switching losses of the inverter. Rather than a new single SC based five-level transformerless inverter topology, a control scheme is also presented to inject a precisely regulated current into the grid that can govern both the active and reactive power support modes. In-depth comparisons between the proposed and cutting-edge MLIs are also provided. All these claims are validated through MATLAB/Simulink and PLECS computer simulation environments. A laboratory-scaled prototype is also built and tested to support the simulated claims further and validate the effectiveness and feasibility of the proposed five-level transformerless inverter topology.

Due to the rapid advancement of power semiconductor devices, the use of voltage source inverters (VSIs) has gained widespread acceptance. As a consequence, the performance of the voltage source inverter has emerged as a critical aspect that is highly reliant on the modulation strategy. The pulse width modulation (PWM) technique is the most widely utilized method of controlling power semiconductor switches of VSI. Power quality is always considered as an industrial concern for VSI-based power system such as grid-connected renewable energy systems and industrial motor drives which largely depends on the PWM technique used for switching. However, the existing PWM schemes for VSIs suffer from high total harmonic distortion (THD) and power loss problems. To mitigate the THD and power loss of VSI, a hybrid PWM technique has been proposed in this paper. The proposed hybrid PWM technique introduces a modified modulating signal along with newly shaped carrier signal. A two-level VSI is used to evaluate the performance of the proposed hybrid PWM technique both for with and without filter conditions against RL load. The proposed hybrid PWM technique offers 0.89% filtered voltage THD and 0.69% filtered current THD which are lower than that of existing PWM techniques. On the contrary, at without filter condition, the proposed hybrid PWM technique shows THDs of 45.77% and 12.50% for inverter output voltage and current, respectively which are also lower than those of existing PWM techniques. Apart from these, the proposed hybrid PWM technique reduces the switching and conduction power losses of the VSI as compared to existing PWM techniques. The simulation works are carried out in MATLAB/Simulink environment and a reduced scale experiment is conducted in laboratory to evaluate the performance of the proposed hybrid PWM technique.

The integration of solar photovoltaic (PV) arrays for induction motor drives (IMDs) has attained a lot of research interest due to the versatile applications of IMD including water pumping, cement industries, electric vehicles, and rolling mills etc. Multilevel inverters (MLIs) are a prominent solution for driving medium voltage induction motors (IMs) due to their superior performances over two-level voltage source inverters (VSIs). However, the power quality performance of MLI fed IMDs greatly depends on the pulse width modulation (PWM) strategy employed. Traditional PWM strategies for MLIs suffer from power quality problem such as lower order harmonics, high THD, unbalanced power loss distribution, high switching power loss, thermal instability and electromagnetic interference (EMI) problems. In this paper, a modified PWM strategy is proposed for a solar PV fed 3-level neutral point clamped (NPC) inverter driven IMD. The proposed PWM strategy introduces a new modulating signal with level shifted triangular carriers. The proposed modulating signal is formed by utilizing a $13^{\mathrm {th}}$ harmonic signal and saturated balanced 3-phase sinusoidal signals. The proposed PWM technique is named as $13^{\mathrm {th}}$ harmonic injected 60°-PWM (THISDPWM). The THISDPWM reduces the lower order harmonics contents, overall THD, and switching power losses of the NPC inverter compared to different existing PWM strategies. Apart from that, a robust artificial neutral network (ANN) based incremental conductance maximum power point tracking (MPPT) algorithm is also introduced to control the dc-link voltage of the PV fed NPC inverter driven IMD system. The presented ANN based dc-link controlled technique ensures stable dc-link voltage against wide range of PV parameters variation. All the simulation works are carried out in MATLAB/Simulink environment and a reduced scale laboratory prototype of the IMD is built and tested to validate the performance of the proposed THISDPWM technique.

Islanded microgrids face difficulties due to the presence of nonlinearity, asynchronous load, and unknown load dynamics. Moreover, conventional control schemes in the islanded microgrids show slow dynamic response, significant voltage-current oscillations, frequency change, low output power quality, and less reference tracking capability. In this regard, a robust and high performance controller is required against the instability issues related to various load conditions and sudden load changes in the solar photovoltaic (PV)-based solar photovoltaic (PV) based islanded microgrids. This paper presents the design and implementation of a second-order high performance resonant controller for robustness and improving the stability of a solar PV based three-phase islanded microgrid (TPMG) under varying system conditions. The design of the proposed controller is based on a backstepping scheme where control Lyapunov functions are used to find transfer functions. The transfer functions that are obtained by this approach are the transfer functions of a resonant controller with proportional-integral controllers. The performance of the proposed controller is investigated in MATLAB/Simulink. The simulation results demonstrate the robustness of the proposed controller in terms of stability, dynamic responses, voltage-current oscillations, total harmonic distortion, and reference tracking of the TPMG. Moreover, the performance of the proposed controller is illustrated against various load dynamics and sudden load changes. A laboratory-scale experiment verifies the simulation results of the proposed controller.

Optimization of supply current total harmonic distortion (THD) of multi-pulse AC-DC power converter fed induction motor drive (IMD) is always a challenging issue. Higher amount of supply current THD degrades the input power quality of IMD. The supply current THD should be controlled in such a way so that it adheres the power quality standard of IEEE-519. With the increase of the pulse number of multi-pulse AC-DC converter, supply current THD increases. In this work, an investigation has been carried out on 6-pulse, 12-pulse, 18-pulse, and 24-pulse AC-DC power converters based IMD. A thorough analysis of input current profile, THD, dynamic responses including stator current, speed, torque profile of the induction motor are highlighted in this work with the various load perturbation conditions. This work will provide a message to the industrial community about the proper selection of AC-DC power converter for IMD application considering power quality and circuit configuration issues. All the investigating works are conducted in MATLAB/Simulink platform.

To maintain the stability of the power system, frequency fluctuations must be reduced in the shortest possible timeframe. Load frequency control (LFC) plays a critical role in achieving this objective by regulating the system frequency and the desired demand or output power in an interconnected network, thereby enabling the system to adapt the load disturbances. In order to effectively mitigate the frequency fluctuation caused by load variation in a single-area power system, a new control strategy integrating a linear quadratic regulator (LQR), a proportional controller, and a damping compensator is proposed in this paper. The proposed controller is named as the LQR-based proportional damping compensator which mitigates the frequency fluctuation of a single-area power system. MATLAB/Simulink simulation is conducted on a single-area power system to demonstrate the efficacy of the proposed control technique. The simulation results demonstrate that the proposed method successfully reduces frequency variations, maintains system frequency within reasonable limits, and substantially reduces the settling time as compared to other existing control techniques. Apart from the simulation analysis, to experimentally validate the performance of the proposed controller, a hybrid multiprocessor-based processor-in-loop (PIL) technique is also introduced in the paper. Both the simulation and experimental results prove the promising performance of the proposed controller for mitigating the frequency fluctuation of a single-area power system.

This paper presents a novel single-phase to single-phase multiconverter topology that can be applied in multiple areas. The proposed multiconverter is designed with only two soft power semiconductor switches (e.g. MOSFET or IGBT), four power diodes and a center-tapped transformer which makes it more compact in size, decrease the gate driving complexity, reduce the total equipment costs and enhance the energy conversion efficiency with minimized losses. Furthermore, the utilization of the transformer in the proposed converter mitigates the multiple AC source requirement problems and provides galvanic isolation which increases the reliability of the converter. Moreover, the presented multiconverter is applicable in various areas including electric traction as a speed controller, induction heating, AC and DC variable power supplies, etc. which signify the competence of this converter in energy conversion appliances. However, a comparative analysis of the offered converter with the existing AC-AC converters is also introduced in this paper with respect to the number of components, equipment costs, gate driving complexity, and application areas. In order to evaluate the performance of the proposed multiconverter, the simulation-based results carried out in MATLAB/Simulink are presented and analyzed in this paper with proper descriptions. Finally, a scaled-down prototype is developed in the laboratory to validate the simulation results and the feasibility of the proposed multiconverter.

A new three phase multilevel inverter with reduced number of components count is proposed in this paper. This inverter is designed using a single DC source per phase to generate multiple level output voltage which makes it suitable for low and medium voltage applications, including ac-coupled renewables or energy storages. A generalized circuit configuration is shown in this paper following which the number of output voltage level can be increased as per expectation. Although, each element endures the voltage stress equivalent to the input DC voltage, the value of total standing voltage (TSV) is reduced by the utilization of minimized number of components with respect to the number of series connected capacitors. Further, staircase modulation scheme is used to generate the switching signals. Hence, the proposed inverter can be operated at low switching frequency with optimal output current harmonic distortion which decreases switching losses and suppresses power factor falling. In order to validate the theoretical explanations and practical performances of the proposed inverter, the hypothesis is simulated for 9, 13 and 39 output voltage level inverters for three phase with a line voltage total harmonic distortion (THD) of 6.06%, 4.16% and 2.10% respectively in MATLAB/Simulink and a 5-level single phase laboratory prototype is implemented in the laboratory.

Photovoltaic (PV) energy systems have found diverse applications in fulfilling the increasing energy demand worldwide. Transformer-less PV inverters convert the DC energy from PV systems to AC energy and deliver it to the grid through a non-isolated connection. This paper proposes a new transformer-less grid-connected PV inverter. A closed-loop control scheme is presented for the proposed transformer-less inverter to connect it with the power grid. The proposed transformer-less inverter reduces extra leakage current and holds the common-mode voltage at a constant point. To eliminate extra leakage current, as well as achieve constant common-mode voltage, a midpoint clamping method is utilized to operate the inverter. The proposed transformer-less inverter is formed of seven insulated gate bipolar transistors (IGBTs) employing a unipolar sinusoidal pulse width modulation (SPWM) technique for switching purposes. An LCL filter is employed to reshape the two-level inverter output voltage and current to obtain closer sinusoidal waveforms. The output voltage and current total harmonic distortion (THD) of the proposed transformer-less inverter were found to be 1.25% and 0.94%, respectively, in the grid-connected mode. The leakage current elimination mechanism with the proposed transformer-less inverter is deeply analyzed in this paper. The performances of the proposed transformer-less inverter were evaluated with MATLAB/Simulink simulation and validated in a laboratory scale experiment.

Due to global warming and shortage of fossil fuels, the grid-connected solar photovoltaic (PV) system has gained significant popularity all over the world. The modular multilevel cascaded (MMC) inverter is the natural choice for step-up transformer and line filter less direct medium voltage grid integration of solar PV systems. However, power quality and loss are the important issues while connecting the PV system to the medium voltage grid through MMC inverter. Modulation technique is the key to maintain output power quality, e.g., total harmonic distortion (THD) and to ensure low switching and conduction losses. In this paper, an advanced modulation technique named “triangle saturated common mode pulse width modulation (TSCMPWM)” control is proposed for a 3-phase 5-level MMC inverter-based grid-tied PV system. Compared to traditional modulation techniques, the proposed TSCMPWM control offers the lowest voltage THD as well as lower inverter power losses. Performance of the proposed modulation technique is evaluated in MATLAB/Simulink environment and tested with a reduced scale prototype test platform. Both simulation and experimental results show the effectiveness of the proposed modulation technique.