Search

The objective of this review paper is to identify the gap in finding out the direction toward the enhancement of heat transfer and the performance of heat exchangers. Heat exchangers can be found in many applications ranging from engineering devices to household consumer appliances. Heat exchangers must offer a good heat transfer performance apart from saving energy. Heat transfer enhancement techniques help to save energy and cool hot components in the design of electronic and mechanical circuits. However, enhancement in heat transfer takes place at the cost of a bearable increase in friction losses and pressure drop. Therefore, miniature heat exchanger systems and the cost of energy, motivate industries to use energy-saving methods in their design. With aging, the most common problem in heat exchangers is the reduction in heat transfer rate. Numerous studies have proved that placing a disturbance occurs in the fluid flow path and it can help to increase the heat transfer rate in the case of worn-out heat exchangers. For decades, researchers are numerically investigating the effects of various kinds of insert tape to improve the heat transfer operation in the heat exchangers. As heat exchangers form the backbone of many industrial processes, the idea of saving energy with the design of a cost-effective tape insert motivated us to work on this area of research. The paper proposes the new model of heat exchanger with an insert having a trapezoidal cut on both sides of an insert and using the different ratios of twist experimentation that will perform and compare the output with the previous studies by using different fluid or phase change materials as a fluid to maximize the performance of heat transfer rate. Also, it aims to find out the impact on friction factor as well pressure drop in the heat exchanger when there is a change in ratios of twist. This research aims to review the findings of earlier researchers in this area and to utilize the knowledge for improving the heat transfer rate of conventional tubes in our future work.

RNA pol II assembly occurs in the cytoplasm before translocation of the enzyme to the nucleus. Affecting this assembly influences mRNA transcription in the nucleus and mRNA decay in the cytoplasm. However, very little is known about the consequences on ncRNA synthesis. In this work, we show that impairment of RNA pol II assembly leads to a decrease in cryptic non-coding RNAs (preferentially CUTs and SUTs). This alteration is partially restored upon overcoming the assembly defect. Notably, this drop in ncRNAs is only partially dependent on the nuclear exosome, which suggests a major specific effect of enzyme assembly. Our data also point out a defect in transcription termination, which leads us to propose that CTD phosphatase Rtr1 could be involved in this process. [ABSTRACT FROM AUTHOR]

The objective of this review paper is to identify the gap in finding out the direction toward the enhancement of heat transfer and the performance of heat exchangers. Heat exchangers can be found in many applications ranging from engineering devices to household consumer appliances. Heat exchangers must offer a good heat transfer performance apart from saving energy. Heat transfer enhancement techniques help to save energy and cool hot components in the design of electronic and mechanical circuits. However, enhancement in heat transfer takes place at the cost of a bearable increase in friction losses and pressure drop. Therefore, miniature heat exchanger systems and the cost of energy, motivate industries to use energy-saving methods in their design. With aging, the most common problem in heat exchangers is the reduction in heat transfer rate. Numerous studies have proved that placing a disturbance occurs in the fluid flow path and it can help to increase the heat transfer rate in the case of worn-out heat exchangers. For decades, researchers are numerically investigating the effects of various kinds of insert tape to improve the heat transfer operation in the heat exchangers. As heat exchangers form the backbone of many industrial processes, the idea of saving energy with the design of a cost-effective tape insert motivated us to work on this area of research. The paper proposes the new model of heat exchanger with an insert having a trapezoidal cut on both sides of an insert and using the different ratios of twist experimentation that will perform and compare the output with the previous studies by using different fluid or phase change materials as a fluid to maximize the performance of heat transfer rate. Also, it aims to find out the impact on friction factor as well pressure drop in the heat exchanger when there is a change in ratios of twist. This research aims to review the findings of earlier researchers in this area and to utilize the knowledge for improving the heat transfer rate of conventional tubes in our future work. [ABSTRACT FROM AUTHOR]

A one-year survey was undertaken of the microbiological quality of carcases and the derived primal cuts, manufacturing meat and offals at twelve Australian export establishments (six beef, three sheep/lamb and three pork). A total of 27,157 microbiological results for aerobic plate count (APC) and generic Escherichia coli were gathered, 15,155 from beef, 8405 from sheep and 3597 from pig establishments. The mean log10 APCs on beef, sheep and pig carcases were 0.84, 1.60 and 1.30 log10 cfu/cm2, respectively. For primals, the mean log10 APC was higher for beef but was similar for sheep and pork primals, with 'outside' cuts having higher counts. For manufacturing meat, the concentration was 2–3 log10 cfu/g, irrespective of species. The prevalence (%) of generic E. coli from beef, sheep and pork was 2.3, 28.4 and 5.4 on carcases; 7.0, 20.6 and 3.2 on primals; and 5.8, 33.6 and 6.1 on manufacturing meat, respectively. The mean log10 APCs of beef, sheep and pork offal were 3.23, 3.18 and 3.37 log10 cfu/g, with tripes and tongues having APCs 1–2 log10 units higher than organ offals. The results reflect improvements in total bacterial loadings compared with previous national baseline surveys. [ABSTRACT FROM AUTHOR]

This paper presents the influence of cuts inspired by kirigami art on the outer surface of a soft actuator with cylindrical geometry. Both the kirigami pattern and orientation were varied to achieve expanding, bending, and twisting motions. Two symmetric kirigami patterns are presented, i.e., cells and stripes, in a horizontal, vertical, and tilted configurations, respectively. We also present the tensile response of the kirigami sheets by using the finite element method (FEM). Then, we show that the soft actuator expands, bends or twists when kirigami patterns are wrapped around it. All actuators were analyzed by performing FEM simulations to evaluate the effects of kirigami patterns on the actuator performance. Among the obtained variants of the expanding and bending actuators, the striped pattern provided the best performance for both motions. We show how the number of cuts and the relationship between the gaps affect the expanding performance. For the twisting motion, we obtained two variants; we present the influence of the change of the inclination angle for both patterns, i.e., cells and stripes. The actuators that presented the best performance for each motion were built; a manufacturing process using the casting technique is described. The validation of the hardware by computer vision is presented.

The objective of this work is to identify which carcass and cut characteristics have the best discriminatory power, between sexes and slaughter weights, through discriminant analysis. Were used 32 goats, with initial average weights of 3.11 kg for males and 3.06 kg, for females, for animals slaughtered at 70 days; 3.65 kg for males and 3.25 kg for females for animals slaughtered at 100 days of weight. Objective assessments consisted of morphometric measurements: external carcass length (ECL); internal carcass length (ICL); leg length (LEL); chest width (CHW); croup width (CRW); thigh perimeter (THP); croup perimeter (CRP); chest perimeter (CHP); chest depth (CHD); internal chest depth (ICD) using the hypsometer and flexible tape (Truper®). In the total of 18 primary variables evaluated, the following variables were included in the discriminant model, using the stepwise method: empty body weight, chest depth, chest width, thigh circumference, neck, loin, leg length, and rump width. The discriminant analysis was efficient to discriminate and identify the carcass and cut characteristics with better discriminatory power between the sex and slaughter weight of the animals.

The relaxor ferroelectric single crystal (1−x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 (PMN-PT) has high piezoelectric constants, and thus has a good application prospect in the field of highly sensitive piezoelectric sensors. In this paper, for relaxor ferroelectric single crystal PMN-PT, the bulk acoustic wave characteristics on pure- and pseudo-lateral-field-excitation (pure- and pseudo-LFE) modes are investigated. LFE piezoelectric coupling coefficients and acoustic wave phase velocities for PMN-PT crystals in different cuts and electric field directions are calculated. On this basis, the optimal cuts of pure-LFE and pseudo-LFE modes of relaxor ferroelectric single crystal PMN-PT are obtained, namely, (zxt)45° and (zxtl)90°/90°, respectively. Finally, finite element simulations are carried out to verify the cuts of pure-LFE and pseudo-LFE modes. The simulation results show that the PMN-PT acoustic wave devices in pure-LFE mode have good energy-trapping effects. For PMN-PT acoustic wave devices in pseudo-LFE mode, when the device is in air, no obvious energy-trapping emerges; when the water (as a virtual electrode) is added to the surface of the crystal plate, an obvious resonance peak and the energy-trapping effect appears. Therefore, the PMN-PT pure-LFE device is suitable for gas-phase detections. While the PMN-PT pseudo-LFE device is suitable for liquid-phase detections. The above results verify the correctness of the cuts of the two modes. The research results provide an important basis for the development of highly sensitive LFE piezoelectric sensors based on relaxor ferroelectric single crystal PMN-PT. [ABSTRACT FROM AUTHOR]

A novel concept of quaternionic fuzzy sets (QFSs) is presented in this paper. QFSs are a generalization of traditional fuzzy sets and complex fuzzy sets based on quaternions. The novelty of QFSs is that the range of the membership function is the set of quaternions with modulus less than or equal to one, of which the real and quaternionic imaginary parts can be used for four different features. A discussion is made on the intuitive interpretation of quaternion-valued membership grades and the possible applications of QFSs. Several operations, including quaternionic fuzzy complement, union, intersection, and aggregation of QFSs, are presented. Quaternionic fuzzy relations and their composition are also investigated. QFS is designed to maintain the advantages of traditional FS and CFS, while benefiting from the properties of quaternions. Cuts of QFSs and rotational invariance of quaternionic fuzzy operations demonstrate the particularity of quaternion-valued grades of membership. [ABSTRACT FROM AUTHOR]

In the Cuban oil industry, it is necessary to adopt new alternatives and technologies to prevent pollution and minimize the environmental impact derived from this activity. Some of the most severe effects include those produced by the actions of oil extraction and management. One of the most concerning issues is the generation of a large volume of petroleum solid waste (contaminants), especially drill cuttings coated with diesel fuel‐based fluids or sludge, since their treatment and final disposal are difficult. [ABSTRACT FROM AUTHOR]

Introduction: Cubital tunnel syndrome (CuTS) is a condition of ulnar nerve dysfunction due to prolonged compression at the elbow often caused by cubitus valgus deformity of lateral epicondyle fracture. The main objective of this study is to share our experience of and to review the role of surgical decompression and anterior transposition (SDAT) of ulnar nerve in long-term relief of the symptoms. Materials and Methods: Retrieval of case records of CuTS and retrograde analysis of data was performed. The inclusion criteria were availability of relevant clinical information, finding of severe nerve compression in nerve conduction study (NCS), insignificant MRI of cervical spine and SDAT. About 100 cases of ulnar nerve compression underwent surgical management from 2008 till 2021. Of them, only 54 fulfilled all the criteria. Minimum follow up period was 18 months after surgery. Results: Among 54 cases, 20 were females, 34 males, and mean age was 31 years. Three most common clinical features were paresthesia, motor weakness and hand muscle atrophy. Symptomatic relief was achieved in 54/54 (100%) and complete motor recovery in 34/54 (63%) cases after SDAT. However, muscle atrophy recovery was not observed in any. There was no surgical complication, no features of recurrence nor was there re-surgery in any at least for 18 months after surgery. Conclusions: SDAT provides long-term relief for CuTS without recurrence. Muscle atrophy is irreversible though other symptoms improve. Therefore, early surgery before appearance of muscle atrophy is advocated. [ABSTRACT FROM AUTHOR]

This paper presents the influence of cuts inspired by kirigami art on the outer surface of a soft actuator with cylindrical geometry. Both the kirigami pattern and orientation were varied to achieve expanding, bending, and twisting motions. Two symmetric kirigami patterns are presented, i.e., cells and stripes, in a horizontal, vertical, and tilted configurations, respectively. We also present the tensile response of the kirigami sheets by using the finite element method (FEM). Then, we show that the soft actuator expands, bends or twists when kirigami patterns are wrapped around it. All actuators were analyzed by performing FEM simulations to evaluate the effects of kirigami patterns on the actuator performance. Among the obtained variants of the expanding and bending actuators, the striped pattern provided the best performance for both motions. We show how the number of cuts and the relationship between the gaps affect the expanding performance. For the twisting motion, we obtained two variants; we present the influence of the change of the inclination angle for both patterns, i.e., cells and stripes. The actuators that presented the best performance for each motion were built; a manufacturing process using the casting technique is described. The validation of the hardware by computer vision is presented. [ABSTRACT FROM AUTHOR]

A one-year survey was undertaken of the microbiological quality of carcases and the derived primal cuts, manufacturing meat and offals at twelve Australian export establishments (six beef, three sheep/lamb and three pork). A total of 27,157 microbiological results for aerobic plate count (APC) and generic Escherichia coli were gathered, 15,155 from beef, 8405 from sheep and 3597 from pig establishments. The mean log10 APCs on beef, sheep and pig carcases were 0.84, 1.60 and 1.30 log10 cfu/cm2, respectively. For primals, the mean log10 APC was higher for beef but was similar for sheep and pork primals, with ‘outside’ cuts having higher counts. For manufacturing meat, the concentration was 2–3 log10 cfu/g, irrespective of species. The prevalence (%) of generic E. coli from beef, sheep and pork was 2.3, 28.4 and 5.4 on carcases; 7.0, 20.6 and 3.2 on primals; and 5.8, 33.6 and 6.1 on manufacturing meat, respectively. The mean log10 APCs of beef, sheep and pork offal were 3.23, 3.18 and 3.37 log10 cfu/g, with tripes and tongues having APCs 1–2 log10 units higher than organ offals. The results reflect improvements in total bacterial loadings compared with previous national baseline surveys.

This article deals with the evaluation of a thickness analysis on the vuts of beech wood using annual rings. The study was performed at the state enterprise Lesy SR, a branch plant in Smolenice on the territory of Forrest District Majdán. In order to perform a thickness analysis of the beech logs, it was necessary to know the number of annual rings on the butt end and the number of annual rings on the small end. Based on these two quantities, it was necessary to derive the number of annual rings in the middle of the trunk. All these characteristics were related to the length of the stem and the thickness of the stem. The data set contained 1000 logs. For a period of 3 years - i.e. from 2017 to 2019 in total for all types of intentional felling, starting with tending intentional felling up to 50 years, tendingt intentional felling over 50 years and ending with prescribed final felling, incidential felling was not included in the investigation. The aim of this publication was to determine the thickness characteristics of beech stem logs, which are characterized in the territory of branch Smolenice by a full-wood stem and to create input quantities for a model log of a beech stem. The results include the average width of annual rings depending on the length of the stem, the average number of annual rings per 1 meter of length, the average reduction in the number of annual rings depending on the length recalculated per 1 meter of length, the average height increment. The results showed interesting findings, the largest average width of annual rings was recorded in improvement intentional felling over 50 years, despite advanced age. Another interesting finding was the average height gain of 0.5 m. The average number of annual rings served to confirm the accuracy of the calculation of the stem thickness depending on the width of the annual ring. The average reduction in the number of annual rings showed the convergence of the stem in cm depending on the length of the cut.

In a fuzzy set (FS), there is a concept of alpha-cuts of the FS for alpha in [0,1]. Further, this concept was extended into (alpha,delta)-cuts in an intuitionistic fuzzy set (IFS) for delta in [0,1]. One of the expansions of FS and IFS is the picture fuzzy set (PFS). Hence, the concept of (alpha,delta)-cuts was developed into (alpha,delta,beta)-cuts in a PFS where beta is an element of [0,1]. Since a picture fuzzy graph (PFG) consists of picture fuzzy vertex or edge sets or both of them, we have an idea to construct the notion of the (alpha,delta,beta)-cuts in a PFG. The steps used in this paper are developing theories and algorithms. The objectives in this research are to construct the concept of (alpha,delta,beta)-cuts in picture fuzzy graphs (PFGs), to construct the (alpha,delta,beta)-cuts coloring of PFGs, and to design an algorithm for finding the cut chromatic numbers of PFGs. The first result is a definition of the (alpha,delta,beta)-cut in picture fuzzy graphs (PFGs) where (alpha,delta,beta) are elements of a level set of the PFGs. Further, some properties of the cuts are proved. The second result is a concept of PFG coloring and the chromatic number of PFG based on the cuts. The third result is an algorithm to find the cuts and the chromatic numbers of PFGs. Finally, an evaluation of the algorithm is done through Matlab programming. This research could be used to solve some problems related to theories and applications of PFGs.

The relaxor ferroelectric single crystal (1−x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 (PMN-PT) has high piezoelectric constants, and thus has a good application prospect in the field of highly sensitive piezoelectric sensors. In this paper, for relaxor ferroelectric single crystal PMN-PT, the bulk acoustic wave characteristics on pure- and pseudo-lateral-field-excitation (pure- and pseudo-LFE) modes are investigated. LFE piezoelectric coupling coefficients and acoustic wave phase velocities for PMN-PT crystals in different cuts and electric field directions are calculated. On this basis, the optimal cuts of pure-LFE and pseudo-LFE modes of relaxor ferroelectric single crystal PMN-PT are obtained, namely, (zxt)45° and (zxtl)90°/90°, respectively. Finally, finite element simulations are carried out to verify the cuts of pure-LFE and pseudo-LFE modes. The simulation results show that the PMN-PT acoustic wave devices in pure-LFE mode have good energy-trapping effects. For PMN-PT acoustic wave devices in pseudo-LFE mode, when the device is in air, no obvious energy-trapping emerges; when the water (as a virtual electrode) is added to the surface of the crystal plate, an obvious resonance peak and the energy-trapping effect appears. Therefore, the PMN-PT pure-LFE device is suitable for gas-phase detections. While the PMN-PT pseudo-LFE device is suitable for liquid-phase detections. The above results verify the correctness of the cuts of the two modes. The research results provide an important basis for the development of highly sensitive LFE piezoelectric sensors based on relaxor ferroelectric single crystal PMN-PT.

A novel concept of quaternionic fuzzy sets (QFSs) is presented in this paper. QFSs are a generalization of traditional fuzzy sets and complex fuzzy sets based on quaternions. The novelty of QFSs is that the range of the membership function is the set of quaternions with modulus less than or equal to one, of which the real and quaternionic imaginary parts can be used for four different features. A discussion is made on the intuitive interpretation of quaternion-valued membership grades and the possible applications of QFSs. Several operations, including quaternionic fuzzy complement, union, intersection, and aggregation of QFSs, are presented. Quaternionic fuzzy relations and their composition are also investigated. QFS is designed to maintain the advantages of traditional FS and CFS, while benefiting from the properties of quaternions. Cuts of QFSs and rotational invariance of quaternionic fuzzy operations demonstrate the particularity of quaternion-valued grades of membership.

The preprocessing of data is an important task in rough set theory as well as in Entropy. The discretization of data as part of the preprocessing of data is a very influential process. Is there a connection between the segmentation of the data histogram and data discretization? The authors propose a novel data segmentation technique based on a histogram with regard to the quality of a data discretization. The significance of a cut's position has been researched on several groups of histograms. A data set reduct was observed with respect to the histogram type. Connections between the data histograms and cuts, reduct and the classification rules have been researched. The result is that the reduct attributes have a more irregular histogram than attributes out of the reduct. The following discretization algorithms were used: the entropy algorithm and the Maximal Discernibility algorithm developed in rough set theory. This article presents the Cuts Selection Method based on histogram segmentation, reduct of data and MD algorithm of discretization. An application on the selected database shows that the benefits of a selection of cuts relies on histogram segmentation. The results of the classification were compared with the results of the Naïve Bayes algorithm. [ABSTRACT FROM AUTHOR]

The saving of leather, an extremely important objective in footwear manufacturing, requires following certains steps in the process of cutting the component parts of a footwear article in order to obtain better use of the leather surface. With this regard, the paper presents how to program the cuts of the outer parts of a shoe item in the cutting department, respectively a model of women shoes. For the chosen item, there were done single cuts for one number of size (10 options), as well as combined cuts of two distinct sizes (45 options). Programming uppers cuts consists in their practical realization, followed by choosing the optimal cuts in order to obtain the best global utilisation index. The value of the global utilisation index depends on the values of the utilisation indices of the simple and combined cutting ways, the programming strategy and the iteration mode of the cutting options. By using the simple and combined cuts, for the developed program resulted a 72.04% global utilization index versus 70.64%, obtained by scheduling only single cuts, requiring a quantity of 91 hides. In the case of cuts options with higher utilisation indices, a judicious programming strategy can lead to an efficient cutting, close to the best automatic data processing program.

This article deals with the evaluation of a thickness analysis on the vuts of beech wood using annual rings. The study was performed at the state enterprise Lesy SR, a branch plant in Smolenice on the territory of Forrest District Majdán. In order to perform a thickness analysis of the beech logs, it was necessary to know the number of annual rings on the butt end and the number of annual rings on the small end. Based on these two quantities, it was necessary to derive the number of annual rings in the middle of the trunk. All these characteristics were related to the length of the stem and the thickness of the stem. The data set contained 1000 logs. For a period of 3 years - i.e. from 2017 to 2019 in total for all types of intentional felling, starting with tending intentional felling up to 50 years, tendingt intentional felling over 50 years and ending with prescribed final felling, incidential felling was not included in the investigation. The aim of this publication was to determine the thickness characteristics of beech stem logs, which are characterized in the territory of branch Smolenice by a full-wood stem and to create input quantities for a model log of a beech stem. The results include the average width of annual rings depending on the length of the stem, the average number of annual rings per 1 meter of length, the average reduction in the number of annual rings depending on the length recalculated per 1 meter of length, the average height increment. The results showed interesting findings, the largest average width of annual rings was recorded in improvement intentional felling over 50 years, despite advanced age. Another interesting finding was the average height gain of 0.5 m. The average number of annual rings served to confirm the accuracy of the calculation of the stem thickness depending on the width of the annual ring. The average reduction in the number of annual rings showed the convergence of the stem in cm depending on the length of the cut. [ABSTRACT FROM AUTHOR]

In a fuzzy set (FS), there is a concept of alpha-cuts of the FS for alpha in [0,1]. Further, this concept was extended into (alpha,delta)-cuts in an intuitionistic fuzzy set (IFS) for delta in [0,1]. One of the expansions of FS and IFS is the picture fuzzy set (PFS). Hence, the concept of (alpha,delta)- cuts was developed into (alpha,delta,beta)-cuts in a PFS where beta is an element of [0,1]. Since a picture fuzzy graph (PFG) consists of picture fuzzy vertex or edge sets or both of them, we have an idea to construct the notion of the (alpha,delta,beta)-cuts in a PFG. The steps used in this paper are developing theories and algorithms. The objectives in this research are to construct the concept of (alpha,delta,beta)-cuts in picture fuzzy graphs (PFGs), to construct the (alpha,delta,beta)-cuts coloring of PFGs, and to design an algorithm for finding the cut chromatic numbers of PFGs. The first result is a definition of the (alpha,delta,beta)-cut in picture fuzzy graphs (PFGs) where (alpha,delta,beta) are elements of a level set of the PFGs. Further, some properties of the cuts are proved. The second result is a concept of PFG coloring and the chromatic number of PFG based on the cuts. The third result is an algorithm to find the cuts and the chromatic numbers of PFGs. Finally, an evaluation of the algorithm is done through Matlab programming. This research could be used to solve some problems related to theories and applications of PFGs. [ABSTRACT FROM AUTHOR]

The preprocessing of data is an important task in rough set theory as well as in Entropy. The discretization of data as part of the preprocessing of data is a very influential process. Is there a connection between the segmentation of the data histogram and data discretization? The authors propose a novel data segmentation technique based on a histogram with regard to the quality of a data discretization. The significance of a cut’s position has been researched on several groups of histograms. A data set reduct was observed with respect to the histogram type. Connections between the data histograms and cuts, reduct and the classification rules have been researched. The result is that the reduct attributes have a more irregular histogram than attributes out of the reduct. The following discretization algorithms were used: the entropy algorithm and the Maximal Discernibility algorithm developed in rough set theory. This article presents the Cuts Selection Method based on histogram segmentation, reduct of data and MD algorithm of discretization. An application on the selected database shows that the benefits of a selection of cuts relies on histogram segmentation. The results of the classification were compared with the results of the Naïve Bayes algorithm.

Abstract: The objective of this work was to evaluate the allometric growth, the correlation of the cuts with the half carcasses, and the muscularity index of the leg of ½ Dorper + ½ Santa Inês lambs slaughtered with 2.0, 3.0, and 4.0 mm of subcutaneous fat thickness (SFT). Twenty-four non-castrated male lambs were used, being distributed according to their weight into three collective pens. Slaughtering occurred as the lambs reached the SFT predetermined by ultrasound. The half carcasses were weighed, dissected, and separated into five cuts: neck, shoulders, rib, loin, and leg. These cuts were dissected and weighed into muscle, subcutaneous fat, intermuscular fat, and bone. In the shoulders, lambs with 2.0 and 4.0 mm SFT showed early growth. In the rib, this early precocity was observed in lambs with 4.0 mm SFT. The leg showed isogonic growth in lambs with 3.0 and 4.0 mm SFT and was the cut that best correlated with the half carcass, regardless of the SFT. The slaughter of ½ Dorper + ½ Santa Inês lambs with 4.0 mm of subcutaneous fat allows obtaining a better allometric growth of the shoulder, rib, and leg cuts, as well as a better leg muscularity index.

The research was carried out to verify the impact of incorrect care practices on the value of trees. The research was carried out on a fragment of a lime-tree alley, located on a local road connecting Wólka Świątkowa and Krynka in the Lublin province. One side of the alley has been subjected to abnormal cuts, exceeding 50% of the volume of the crown, while the other remains intact. For this purpose, an analysis of the impact of the applied treatments on the condition of trees on the Rollof scale, analysis of life prognoses using the SULE method and the analysis of tree values and the assessment of tree loss as a result of cuts ensuing from the use of incorrect treatments were conducted. The analyses confirmed that the use of incorrect cuts contributed to the decline in the value of trees. The loss is so large that 1/3 of damaged trees have no chance for long and safe; moreover, these trees have lost 68% of their value.

The effects of growth stimulants consist of activating plant physiological processes, which positively affects vegetative and generative growth, increasing the yield and its quality. The aim of the experiment was to study the effect of microbial and amino acid products on the quality of grassland silage; their application in different combinations was an experimental factor. According to the results, the foliar application of the amino acid and microbial products had a statistically significant effect on the chemical composition of silage. In comparison to control, silage produced from plants treated with those growth stimulants contained significantly more total protein in dry matter, while crude fiber content changed only slightly. In addition, due to higher lactic acid content, the quality of silage treated with the stimulants was higher than the quality of control plants. To sum up, the foliar treatment of plants with microorganisms in combination with amino acids resulted in a significant increase in the content of desired components, with a higher nutritional value of the silage.

The current work analized ofthe pH variation, at the level ofthe 12a dorsal vertebra for the U. E., 9 a dorsal vertebra for Kosher cuts and a1l the diferent cuts (nine at total) obteiled from the front quaters bovines. For determination were used cooled quaters of bovines, convention Israel - Argentina (7º in 24 Hs.) and back quartes naturated in traditional form (24 at 48 Hs. at the temperature 01' carnera between 2 ºC and 4ºC). It was determinated the pH in the cuts after the entrance to despostes and sukequently at find rinse, they were not observed variations at the values obteined, It wasrnade several determinations for aplications atatistic methods to many samples , normal distribution (Gauss). They were observed pH variation from cooled cuts (Israel) and maturated cuts (U. E.) near 0,3 upl l. In someone cuts the pH is not constant , there observed the flexor muscles in shin, neck and shank base a greater pH., (more than 6 upIl); the congelation and descongelation no make variations. As the result of pH in not constant in every cuts, the defference deppend al the considerated muscle very important in shin, neck and shank were the flexors musele in accord depending of the acnviry and or relation between conectiv tissue, the ph medition were not minor at 6 uph, independently of cooled or maduration procedures

RNA pol II assembly occurs in the cytoplasm before translocation of the enzyme to the nucleus. Affecting this assembly influences mRNA transcription in the nucleus and mRNA decay in the cytoplasm. However, very little is known about the consequences on ncRNA synthesis. In this work, we show that impairment of RNA pol II assembly leads to a decrease in cryptic non-coding RNAs (preferentially CUTs and SUTs). This alteration is partially restored upon overcoming the assembly defect. Notably, this drop in ncRNAs is only partially dependent on the nuclear exosome, which suggests a major specific effect of enzyme assembly. Our data also point out a defect in transcription termination, which leads us to propose that CTD phosphatase Rtr1 could be involved in this process.

The effect of PEF processing and chilled storage on the volatile composition and sensory properties of chilled and frozen lamb cuts was investigated in this study. Results showed that PEF-treated chilled and frozen lamb cuts varied in temporal flavour attributes with storage. Storage for 7 days resulted in oxidized flavour, while PEF treatments for all chilled and frozen cuts were associated with browned and livery flavour attributes. Partial least squares regression (PLSR) was applied to determine the predictive relationships between the volatile composition, fatty acid and amino acid profiles, and sensory responses for PEF treated lamb cuts. The results showed that some volatile compounds (2-nonanone, 2-pentylfuran, pyrrole, methyl pyrazine, 2-ethyl-3-methyl pyrazine, and thiophene) correlated well with the meaty and juicy flavour of PEF treated frozen lamb cuts. In PEF treated chilled lamb cuts, meaty and juicy flavours were associated with the presence of fatty acids (C18:0, SFA, 20:5(n-3), and n-3). In contrast, livery and browned perception of both PEF processed chilled and frozen lamb cuts were associated with the presence of amino acids (threonine, phenylalanine, isoleucine, tyrosine, and methionine), and some volatile compounds (heptanal, 2-ethylfuran, pyridine, dimethyl disulphide, dimethyl trisulphide, and 3,5-diethyl-2-methyl pyrazine). Overall, these results imply that careful consideration of type of meat cuts, PEF pre-treatment, and storage are important when subjecting lamb meat to PEF processing.

The saving of leather, an extremely important objective in footwear manufacturing, requires following certains steps in the process of cutting the component parts of a footwear article in order to obtain better use of the leather surface. With this regard, the paper presents how to program the cuts of the outer parts of a shoe item in the cutting department, respectively a model of women shoes. For the chosen item, there were done single cuts for one number of size (10 options), as well as combined cuts of two distinct sizes (45 options). Programming uppers cuts consists in their practical realization, followed by choosing the optimal cuts in order to obtain the best global utilisation index. The value of the global utilisation index depends on the values of the utilisation indices of the simple and combined cutting ways, the programming strategy and the iteration mode of the cutting options. By using the simple and combined cuts, for the developed program resulted a 72.04% global utilization index versus 70.64%, obtained by scheduling only single cuts, requiring a quantity of 91 hides. In the case of cuts options with higher utilisation indices, a judicious programming strategy can lead to an efficient cutting, close to the best automatic data processing program. [ABSTRACT FROM AUTHOR]

There are two ways of solving eddy current problems with an edge element $h$ -conforming formulation in the case of non-simply-connected conductors: first employs a “fake” artificial conductivity in part of the insulator. Second uses the cohomology theory to define a scalar magnetic potential in the whole insulator. This contribution provides, for the first time, a thorough comparison between these methods. We concentrate on the accuracy and computational effort required to solve a problem using both of the two methods. [ABSTRACT FROM AUTHOR]

By the ordered tree inclusion we will check whether a pattern tree P can be included in a target tree T, where the order of siblings in both P and T matters. This problem has many applications in practice, such as retrieval of documents, data mining, and RNA structure matching. In this paper, we propose an efficient algorithm for this problem. Its time complexity is bounded by ${\text{O}(\vert }T\vert \cdot \;min\{h_{P}{,\;\vert \text{leaves(}}P)\vert \})$O(|T|·min{hP,|leaves(P)|}), with ${\text{O}(\vert }T\vert + \vert P\vert)$O(|T|+|P|) space being used, where hP (hT) represents the height of P (resp., T) and leaves (P) stands for the set of the leaves of P. Up to now the best algorithm for this problem needs $\Theta (\vert T\vert \cdot \vert leaves(P)\vert)$Θ(|T|·|leaves(P)|) time and ${\text{O}(\vert }P\vert + \vert T\vert)$O(|P|+|T|) space. Extensive experiments have been done, which show that the new algorithm can perform much better than the existing ones in practice. [ABSTRACT FROM AUTHOR]

In the paper, calculation of stability and protection of slopes on a section of the WF Mesihovina access road was performed. The calculation was carried out in the software Geostudio (Geo-Slope International Ltd. Calgary, Canada) with adoption of the Spencer method. After the calculation, the type of protection that is used for protection of slopes from local effects was adopted. [ABSTRACT FROM AUTHOR]

In the paper, calculation of stability and protection of slopes on a section of the WF Mesihovina access road was performed. The calculation was carried out in the software Geostudio (Geo-Slope International Ltd. Calgary, Canada) with adoption of the Spencer method. After the calculation, the type of protection that is used for protection of slopes from local effects was adopted. [ABSTRACT FROM AUTHOR]

Numerous activities in food services can affect worker health and safety, given that daily food preparation routines involve the use of sharp instruments, steam, hot liquids, noise, frozen items, harsh cleaning chemicals, and heavy lifting. The objective of this study was to identify relationships among work activities that affect health and safety among food service workers. The methodology consisted of an integrative review of documentary and bibliographic research, using National Classification of Economic Activities as a data collection criterion and Ministry of Labor and Employment data on work accidents in food services between 2010 and 2020. Work accidents, which may or may not be accompanied by a work accident report, are classified according to type: at work, commuting to work, or occupational illness. During the study period, 169,609 work accidents occurred among food industry workers, which was 12% of the total number of work accidents recorded nationwide in all sectors. The most frequent accident types among food service workers were cuts, burns, falls, and those due to incorrect posture. Training, best practices, professional ethics, functional planning, and periodic and preventive maintenance are important strategies for providing the best working conditions in food services., Competing Interests: Conflicts of interest: None

Schemes of ductile and brittle fracture of a microlayered plate with cuts upon the change in its temperature field have been presented. The influence of the microinhomogeneity of the plate′s material on its thermal conductivity, elasticity, and heat capacity, and also on the value of stresses in it has been investigated. [ABSTRACT FROM AUTHOR]

Catastrophic health events are natural or man-made incidents that create casualties in numbers that overwhelm the response capabilities of healthcare systems. Proper response planning for such events requires community-based surge solutions such as the location of alternative care facilities and ways to improve coordination by considering triage and the movement of self-evacuees. In this paper, we construct a three-stage stochastic programming model to locate alternative care facilities and allocate casualties in response to catastrophic health events. Our model integrates casualty triage and the movement of self-evacuees in a systemic response framework that treats uncertainties involved in such large-scale events as probabilistically distributed scenarios. Solution times being instrumental to the practicality of the model, we propose an algorithm, based on Benders decomposition, to generate good solutions fast. We derive new valid inequalities, which we add to the Benders decomposition master problem to reduce the number of weak feasibility cuts generated. Because our algorithm can also be ineffective if the number of scenarios is large, we propose a two-stage approximation model that attempts to guess good third-stage solutions without third-stage decision variables and constraints. Our model, algorithm, and two-stage approximation are implemented in the case study of an earthquake situation in California based on the realistic ShakeOut Scenario data. [ABSTRACT FROM AUTHOR]

Solving eddy current problems formulated by using a magnetic scalar potential in the insulator requires a topological pre-processing to find the so-called first cohomology basis of the insulating region, which may be very time-consuming for challenging industrially driven problems. The physics-inspired Dłotko–Specogna (DS) algorithm was shown to be superior to alternatives in performing such a topological pre-processing. Yet, the DS algorithm is particularly fast when it produces as output not a regular cohomology basis but a so-called lazy one, which contains the regular one but it keeps also some additional redundant elements. Having a regular basis may be advantageous over the lazy basis if a technique to produce it would take about the same time as the computation of a lazy basis. In the literature, such a technique is missing. This paper covers this gap by introducing modifications to the DS algorithm to compute a regular basis of the first cohomology group in practically the same time as the generation of a lazy cohomology basis. The speedup of this modified DS algorithm with respect to the best alternative reaches more than two orders of magnitudes on challenging benchmark problems. This demonstrates the potential impact of the proposed contribution in the low-frequency computational electromagnetics community and beyond. [ABSTRACT FROM AUTHOR]

Copyright of Ecological Engineering / Inżynieria Ekologiczna is the property of Polish Society of Ecological Engineering and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

We consider an orbit category of the bounded derived category of a path algebra of type A n which can be viewed as a − ( m + 1 ) -cluster category, for m ⩾ 1 . In particular, we give a characterisation of those maximal m -rigid objects whose endomorphism algebras are connected, and then use it to explicitly study these algebras. Specifically, we give a full description of them in terms of quivers and relations, and relate them with (higher) cluster-tilted algebras of type A . As a by-product, we introduce a larger class of algebras, called tiling algebras . [ABSTRACT FROM AUTHOR]

This study aimed to evaluate carcass and noncarcass components of Santa Inês lambs fed diets containing different proportions of mango meal (MF) replacing corn. Twenty four Santa Inês lambs, castrated, with initial live weight of 23.3 kg, were used. Animals were housed in individual pens and fed isonitrogenous diets containing four levels of corn replaced by mango meal for 77 days. Roughage:concentrate ratio was 40:60 and Pennisetum purpureum Schum. in natura was used as roughage source. The completely randomized experimental design with four treatments and six replications was used. Considering the carcass weight and yield components, influences of corn replacement were not observed (P> 0.05), except for brisket and hindquarter weights and hindquarter yield. Quantitative characteristics of eye-muscle area (fat thickness and tissue composition) of Santa Inês lambs were also unchanged. Thus, the MF can be used as food for Santa Inês lambs without damage to quantitative and qualitative carcass and noncarcass characteristics.

When solving eddy-current problems containing topologically non-trivial conductors with formulations using the magnetic scalar potential in the insulators, cohomology generators are necessary to obtain a well-defined problem. The Dłotko–Specogna (DS) algorithm is a simple and efficient tool to compute the lazy generators of the first cohomology group of the insulator that can be used in such potential design. This paper introduces an upgrade in the DS algorithm that speeds up the execution for very complicated geometries. Moreover, this paper provides, for the first time, a detailed comparison of computational resources needed for the topological pre-processing by our toolbox and by the tool to compute a standard cohomology basis available in the mesh generator GMSH. In addition, we make our implementation of DS algorithm available for download on request for non-profit use as a Topoprocessor package. [ABSTRACT FROM AUTHOR]

This paper presents a novel technique to perform the topological pre-processing needed in formulations based on an electric vector potential and a magnetic scalar potential when the eddy-current problem being solved is subject to periodic boundary conditions. In this case, in fact, all the techniques to produce the generators for the first cohomology group introduced in the literature cannot be used directly on the input mesh. The novel technique is very fast and it is used to model cables for power delivery. [ABSTRACT FROM AUTHOR]

We present a new multiplayer game model for the interaction and the flow of information in a distributed system. The players are tokens on a Petri net. As long as the players move in independent parts of the net, they do not know of each other; when they synchronize at a joint transition, each player gets informed of the causal history of the other player. We show that for Petri games with a single environment player and an arbitrary bounded number of system players, deciding the existence of a safety strategy for the system players is EXPTIME-complete. [ABSTRACT FROM AUTHOR]

Introduction: Untreated cuts in some period of time, caused by various reasons, can be a problem. Alternative therapy used to speed up the healing of the cut is Nigella Sativa (NS). Objective: to investigate the number of fibroblast and collagen by giving 40% and 60% NS seed extract on the cut. Methods: post test only control group design, 48 male balb/c strain rats were divided into 2 large groups, with each cage contained 24 rats. Each group then divided to 4. Each group is subdivided into 4. Nigella sativa seed extract ointment with a concentration of 40% (NS-40) and 60% (NS-60) smeared 3x daily for 7 days (fibroblasts) and 14 days (collagen). Evaluation derived from preparations using HE staining and Masson's Trichrome respectively. Results: Mann Whitney analysis shows that the number of fibroblasts and collagen in the CG group, NS-40, and NS- 6 0 Higher than CN, P <0.05. The number of fibroblasts in the NS-40 and NS-60 was not significantly different compared to the CG, as well as CN-40 with CN-60, p> 0.05. While the number of collagen in CN-60 were significantly higher than CN-40, p<0.05. Conclusion : administration of Nigella sativa seed extract ointment with a concentration of 40% and 60% in cuts for 7-14 days increase the number of fibroblasts and collagen, resulting in a shorter healing period. [ABSTRACT FROM AUTHOR]