Search

Wood is a very aesthetically pleasing and environmentally friendly material that can be used both indoors and outdoors. Many research teams are now paying closer attention to polymer modification using furfuryl alcohol or biochar because of its potential for commercial applications. It is anticipated that this kind of material will be long-lasting and maintain its mechanical properties over time. In this paper, spruce wood was modified by a furfuryl alcohol solution enriched by biochar using vacuum infiltration. Therefore, the purpose of this work was to investigate whether spruce wood was suitable for this treatment and to evaluate the effects of thermal degradation properties on prepared composite. Thermogravimetric analysis of raw wood (W), furfurylated wood (FW), and biochar-furfurylated wood bio-composite (BFW) reveals significant differences in its thermal stability. Wood exhibits the lowest thermal stability due to its composition. BFW showed higher thermal stability than wood. FW decomposes similarly to BFW but shows higher mass loss at low temperatures. The obtained results proved increasing two key fire characteristics (decrease of effective heat of combustion and carbon monoxide yield) of BFW in comparison with pristine spruce wood.

Furfurylation can effectively improve the quality of fast-growing wood, but its leachability is unclear. In this study, fast-growing poplar (Populus sp.) and Chinese fir (Cunninghamia lanceolata (Lamb.) Hook.) were impregnated with low concentrations of 5%–20% furfuryl alcohol (FA), and the chemical and microscopic changes during leaching tests were analyzed by UV spectra and confocal laser scanning microscopy (CLSM). The results show that FA impregnation can regulate the weight percentage gain, but its effectiveness in regulating the cell wall bulking coefficient decreased as the impregnation concentration was increased. Impregnation with 15% and 20% FA showed no significant difference in the effect on volume swelling efficiency. The inverse relationship between the concentration of FA and the leaching rate was demonstrated by leaching tests, UV spectra, and CLSM. Notably, the leaching rate of poplar and Chinese fir wood was more than 30% when impregnated with 5% FA. Although the entirety of the furfuryl alcohol was deposited in the cell wall when impregnated with low concentrations of FA, the binding was not stable. The weight percentage gain of furfurylated Chinese fir was greater than that of poplar, but its leaching rate was lower, indicating that the cured furfuryl alcohol resin in poplar was not as stable as that in Chinese fir. Therefore, differences in tree species should be considered in low-concentration FA impregnation, as the improvement effect of concentrations below 10% on the properties of fast-growing wood is weak and the leaching rate of FA is significant. [ABSTRACT FROM AUTHOR]

Furfurylation can effectively improve the quality of fast-growing wood, but its leachability is unclear. In this study, fast-growing poplar (Populus sp.) and Chinese fir (Cunninghamia lanceolata (Lamb.) Hook.) were impregnated with low concentrations of 5%–20% furfuryl alcohol (FA), and the chemical and microscopic changes during leaching tests were analyzed by UV spectra and confocal laser scanning microscopy (CLSM). The results show that FA impregnation can regulate the weight percentage gain, but its effectiveness in regulating the cell wall bulking coefficient decreased as the impregnation concentration was increased. Impregnation with 15% and 20% FA showed no significant difference in the effect on volume swelling efficiency. The inverse relationship between the concentration of FA and the leaching rate was demonstrated by leaching tests, UV spectra, and CLSM. Notably, the leaching rate of poplar and Chinese fir wood was more than 30% when impregnated with 5% FA. Although the entirety of the furfuryl alcohol was deposited in the cell wall when impregnated with low concentrations of FA, the binding was not stable. The weight percentage gain of furfurylated Chinese fir was greater than that of poplar, but its leaching rate was lower, indicating that the cured furfuryl alcohol resin in poplar was not as stable as that in Chinese fir. Therefore, differences in tree species should be considered in low-concentration FA impregnation, as the improvement effect of concentrations below 10% on the properties of fast-growing wood is weak and the leaching rate of FA is significant.

Furfurylation with a low concentration of furfuryl alcohol (FA) promotes the improvement of the properties and the effectiveness of FA on cell–wall action without darkening the furfurylated wood to the point that it affects its applications. In this paper, the effects of furfurylation on the hygroscopicity and water uptake dimensional stability of poplar (Populus sp.) and Chinese fir (Cunninghamia lanceolata) were analyzed. Meanwhile, the distribution of FA resin, the relationship between wood and water, the change in pore size distribution, and the weight percentage gain and cell wall bulking coefficient of wood were also investigated. The results were as follows: (1) A low concentration of FA could better enter the cell walls of the Chinese fir than the poplar, as FA resin was almost cured in the secondary walls, cell corners, and compound middle lamellae when a 10% concentration of FA was applied to the Chinese fir and poplar. When the FA concentration was increased to 30%, there were no significant increases in the amount of FA entering the cell walls and the amounts of FA cured in the cell lumen of the poplar were greater than those of the Chinese fir. Meanwhile, the modification of cell walls was more suitable in poplar than in Chinese fir. (2) The pointed ends of the pit chambers and the pit apertures (800–1000 nm) in the poplar and the small pores of the pit membranes and the pit apertures (1–6 μm) in the Chinese fir were partially deposited by the FA resin, which formed new pores in the size ranges of 80–600 nm and 15–100 nm, respectively. The porosity of the poplar was greater than that of the Chinese fir, and the bulk density of the poplar was less than that of the Chinese fir before and after modification. (3) Furfurylation with a low concentration of FA was able to better reduce the equilibrium moisture content, improve the anti-swelling efficiency, and enhance the dimensional stability of the poplar wood compared to the Chinese fir. Furfurylation effectively reduced water uptake due to the hydrophobic property of the FA resin. The water uptake of the Chinese fir increased by 17%–19% in second cyclic water soaking when treated with FA with various concentrations, which indicated the loss and leaching of FA resin during the test. Low-field NMR was used to demonstrate that the furfurylation not only reduced the amount of water but also affected the combination state of bound and free water with wood. Thus, furfurylation at a low concentration is a feasible method by which to extend applications of furfurylated wood. [ABSTRACT FROM AUTHOR]

There is increasing interest in furfurylated wood, but the polymerization mechanism between its internal polyfurfuryl alcohol (PFA) and lignin is still uncertain. This paper investigated the distribution of PFA and the feasibility of the polymerization of PFA with lignin in furfurylated balsa wood. The wood first immersed in the furfuryl alcohol (FA) solution followed by in situ polymerization and the distribution of PFA was characterized by Raman, fluorescence microscopy, SEM, and CLSM. Then, the mill wood lignin (MWL) of balsa wood and lignin model molecules were catalytically polymerized with PFA, respectively, studying the mechanism of interaction between PFA and lignin. It was concluded that PFA was mainly deposited in cell corner with high lignin concentration, and additionally partly deposited in wood cell cavity due to high concentration of FA and partial delignification. TGA, FTIR, and NMR analysis showed that the cross-linked network structure generated by the substitution of MWL aromatic ring free position by PFA hydroxymethyl enhanced the thermal stability. New chemical shifts were established between PFA and C5/C6 of lignin model A and C2/C6 of model B, respectively. The above results illustrated that lignin-CH2-PFA linkage was created between PFA and lignin in the wood cell wall. [ABSTRACT FROM AUTHOR]

Furfurylation with a low concentration of furfuryl alcohol (FA) promotes the improvement of the properties and the effectiveness of FA on cell–wall action without darkening the furfurylated wood to the point that it affects its applications. In this paper, the effects of furfurylation on the hygroscopicity and water uptake dimensional stability of poplar (Populus sp.) and Chinese fir (Cunninghamia lanceolata) were analyzed. Meanwhile, the distribution of FA resin, the relationship between wood and water, the change in pore size distribution, and the weight percentage gain and cell wall bulking coefficient of wood were also investigated. The results were as follows: (1) A low concentration of FA could better enter the cell walls of the Chinese fir than the poplar, as FA resin was almost cured in the secondary walls, cell corners, and compound middle lamellae when a 10% concentration of FA was applied to the Chinese fir and poplar. When the FA concentration was increased to 30%, there were no significant increases in the amount of FA entering the cell walls and the amounts of FA cured in the cell lumen of the poplar were greater than those of the Chinese fir. Meanwhile, the modification of cell walls was more suitable in poplar than in Chinese fir. (2) The pointed ends of the pit chambers and the pit apertures (800–1000 nm) in the poplar and the small pores of the pit membranes and the pit apertures (1–6 μm) in the Chinese fir were partially deposited by the FA resin, which formed new pores in the size ranges of 80–600 nm and 15–100 nm, respectively. The porosity of the poplar was greater than that of the Chinese fir, and the bulk density of the poplar was less than that of the Chinese fir before and after modification. (3) Furfurylation with a low concentration of FA was able to better reduce the equilibrium moisture content, improve the anti-swelling efficiency, and enhance the dimensional stability of the poplar wood compared to the Chinese fir. Furfurylation effectively reduced water uptake due to the hydrophobic property of the FA resin. The water uptake of the Chinese fir increased by 17%–19% in second cyclic water soaking when treated with FA with various concentrations, which indicated the loss and leaching of FA resin during the test. Low-field NMR was used to demonstrate that the furfurylation not only reduced the amount of water but also affected the combination state of bound and free water with wood. Thus, furfurylation at a low concentration is a feasible method by which to extend applications of furfurylated wood.

There is increasing interest in furfurylated wood, but the polymerization mechanism between its internal polyfurfuryl alcohol (PFA) and lignin is still uncertain. This paper investigated the distribution of PFA and the feasibility of the polymerization of PFA with lignin in furfurylated balsa wood. The wood first immersed in the furfuryl alcohol (FA) solution followed by in situ polymerization and the distribution of PFA was characterized by Raman, fluorescence microscopy, SEM, and CLSM. Then, the mill wood lignin (MWL) of balsa wood and lignin model molecules were catalytically polymerized with PFA, respectively, studying the mechanism of interaction between PFA and lignin. It was concluded that PFA was mainly deposited in cell corner with high lignin concentration, and additionally partly deposited in wood cell cavity due to high concentration of FA and partial delignification. TGA, FTIR, and NMR analysis showed that the cross-linked network structure generated by the substitution of MWL aromatic ring free position by PFA hydroxymethyl enhanced the thermal stability. New chemical shifts were established between PFA and C5/C6 of lignin model A and C2/C6 of model B, respectively. The above results illustrated that lignin-CH2-PFA linkage was created between PFA and lignin in the wood cell wall.

In general fast-growing tree species harvested at a young age has substantial amount of sapwood. It also contains juvenile wood, which has undesirable inferior physical and mechanical properties. Having sapwood and juvenile wood in the trees makes them very susceptible to be attacked by biological deterioration specifically termites in a tropical environment. The main objective of this study was to investigate the termite resistance of four fast-growing Indonesian wood species treated with furfuryl alcohol and imidacloprid. Wood specimens from sengon (Falcataria moluccana), jabon (Anthocephalus cadamba), mangium (Acacia mangium), and pine (Pinus merkusii) were impregnated with furfuryl alcohol, using tartaric acid and heat as well as treated with imidacloprid for the polymerization process. All of the specimens were exposed to environmental conditions in the field for three months. Based on the findings in this work, the untreated control samples had higher weight loss values and lower protection levels than those of imidacloprid-treated and furfurylated samples of all four species. It appears that furfurylation and imidacloprid treatment of such fast-growing species had a significant impact regarding their resistance against termite so that their service life can be extended during their utilization. [ABSTRACT FROM AUTHOR]

In general fast-growing tree species harvested at a young age has substantial amount of sapwood. It also contains juvenile wood, which has undesirable inferior physical and mechanical properties. Having sapwood and juvenile wood in the trees makes them very susceptible to be attacked by biological deterioration specifically termites in a tropical environment. The main objective of this study was to investigate the termite resistance of four fast-growing Indonesian wood species treated with furfuryl alcohol and imidacloprid. Wood specimens from sengon (Falcataria moluccana), jabon (Anthocephalus cadamba), mangium (Acacia mangium), and pine (Pinus merkusii) were impregnated with furfuryl alcohol, using tartaric acid and heat as well as treated with imidacloprid for the polymerization process. All of the specimens were exposed to environmental conditions in the field for three months. Based on the findings in this work, the untreated control samples had higher weight loss values and lower protection levels than those of imidacloprid-treated and furfurylated samples of all four species. It appears that furfurylation and imidacloprid treatment of such fast-growing species had a significant impact regarding their resistance against termite so that their service life can be extended during their utilization.

Copyright of Wood Industry / Drvna Industrija is the property of Drvna Industrija and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)