Search

In this study, a method for removing water from biosolids that uses dimethyl ether (DME) as an extractant was considered. This study evaluates the applicability of the DME dewatering method to biosolid cakes by using a DME flow-type experimental apparatus. It was found that a high dewatering ratio is clearly achieved by increasing the liquefied DME/biosolid ratio and lowering the liquefied DME linear velocity. As the liquefied DME/biosolid ratio was increased, the carbon content in dewatered biosolid showed a slight decrease and the TOC concentration in separated liquid increased significantly. Finally, the input energy Es to remove 1 kg of water from the biosolid cake, using both the DME dewatering method and the conventional drying method was estimated. The calculation shows that Es for the DME dewatering process is approximately a third of Es for the conventional thermal drying process. [ABSTRACT FROM AUTHOR]

This article describes the dewatering of sewage sludge using liquefied dimethyl ether (DME), which clarified the effect of sludge type and its particle size. Changes in the heating value of the dewatered sludge were also examined. In addition, the change in dewaterability upon reuse of the liquefied DME was investigated experimentally. Regardless of the nature of the sludge, its dewatering behavior was similar. The amount of dewatered water could be increased by decreasing the diameter of the sludge cake. Complete drying of the sludge cake via DME dewatering resulted in retention of approximately 96% of the heating value (17.7 MJ/kg-sludge) of the original sludge cake dry base (18.4 MJ/kg db). The DME could be recovered after extraction, and reuse experiments showed that liquefied DME dewatering performance was unchanged after five reuses. [ABSTRACT FROM AUTHOR]

In this study, we evaluated the applicability of the dimethyl ether (DME) dewatering method originally developed for high-moisture coal to superabsorbent polymer (SAP) and disposable diapers. It was found that liquefied DME successfully extracts water from SAP and disposable diapers. However, the polypropylene outer film and polyurethane used in diapers tended to dissolve in the liquefied DME and were subsequently released with the water discharged. These compounds are highly viscous, making it difficult to remove them from the drain outlet of the prototype. Therefore, the mechanics of the drain outlet should be considered in future studies. [ABSTRACT FROM AUTHOR]

We proposed a method for the deodorising and dewatering of biosolids. In the proposed method, liquefied dimethyl ether (DME) was used as an extractant for odorous components and water. We developed a bench-scale experiment to almost completely deodorize and dewater biosolids by using liquefied DME at room temperature. The deodorized and dewatered biosolids have sufficient caloric density and can be used as a carbon neutral fuel. Water Environ, Res., 83, 23 (2011). [ABSTRACT FROM AUTHOR]

Abstract: We investigated whether polychlorinated biphenyls (PCBs) and water could be simultaneously removed from river sediment by solvent extraction using liquefied dimethyl ether (DME) as the extractant. DME exists in a gaseous state at normal temperature and pressure and can dissolve organic substances and some amount of water; therefore, liquefied DME under moderate pressure (0.6–0.8MPa) at room temperature can be effectively used to extract PCBs and water from contaminated sediment, and it can be recovered from the extract and reused easily. First, we evaluated the PCB and water extraction characteristics of DME from contaminated sediment. We found that 99% of PCBs and 97% of water were simultaneously extracted from the sediment using liquefied DME at an extraction time of 4320s and a liquefied DME/sediment ratio of 60mLg−1. The extraction rate of PCBs and water was expressed in terms of a pseudo-first-order reaction rate. Second, we estimated the amount of DME that was recovered after extraction. We found that 91–92% of DME could be recovered. In other words, approximately 5–10% of DME was lost during extraction and recovery. It is necessary to optimize this process in order to recover DME efficiently. The extraction efficiency of the recovered DME is similar to that of the pure DME. From the results, we conclude that solvent extraction using liquefied DME is suitable for extracting PCBs and water from contaminated sediment. [Copyright &y& Elsevier]