Search

In this work, thermal aging aspects of mineral oil, ester oils (synthetic and natural), mixed oil have been reported. All the samples were thermally stressed at 110°C, 140°C, 160°C, and 185°C for 2 weeks each. Concentration of dissolved decay contents in oil, flash point of insulation oil, and linear thermal expansion coefficients of solid insulation with aging have been studied using ultraviolet visible spectroscopy, flash point and dilatometry analysis respectively. Change in functional groups of the insulation oils with aging have been understood by Fourier Transform Infrared Spectroscopy analysis. Additionally, diffusion of oil-moisture mixture into paper with aging and corresponding effect on dielectric strength of paper has been also examined. Further, design and monitoring aspects of ester and mixed oil filled transformers have been also emphasized. It is observed that ester dielectric fluids and ester content as an additive in mineral oil improves the performance of solid insulation. Importantly, blended oil offer an advantage of retarding the degradation of oil as well as solid insulation accompanied by reduced cost of oil when compared to pure synthetic esters. [ABSTRACT FROM AUTHOR]

The paper presents research results of different properties of mixtures of the synthetic ester with mineral oil and synthetic ester with natural ester. For different concentrations of both mixtures, the following properties were investigated: flash point (open and closed cup), fire point (open cup), net calorific value, breakdown voltage, relative permittivity, dissipation factor, conductivity and dissipation factor. In order to compare results, prepared mixtures and base liquids were carefully arranged under uniform climatic conditions. This meant that the prepared samples had the same relative humidity. The obtained results were compared with the results of the base liquids. In addition, results of the investigation were analyzed in terms of fire safety and changes of electrical properties, in the context of the use of synthetic ester/mineral oil and synthetic ester/natural ester mixtures as insulation liquids in power transformers. [ABSTRACT FROM AUTHOR]

This paper presents experimental results of a comparative study of the characteristics of streamers propagating in olive oil and breakdown voltage with mineral oil, rapeseed oil (natural ester) and tetra-ester and methyl oleate (synthetic ester liquids). The comparison focuses more particularly on the pattern, stopping length, associated current and electrical charge of streamers propagating in a point-plane electrodes geometry under (1.2/50 μs) lightning impulse (LI) voltage as well as breakdown voltages under AC and LI voltages. A statistical analysis of breakdown voltages is also achieved. It is shown that the streamer characteristics (streamers shape, stopping length, associated current and electrical charge) of olive oil in small gaps are comparable to those of mineral oil. Breakdown voltages under AC and LI voltages are found to be higher in olive oil than in mineral oil. Consequently, olive oil can constitute a potential substitute for mineral oil in in high voltage power transformers. [ABSTRACT FROM AUTHOR]

This paper presents the results of experimental characterization of creeping discharges propagating over pressboard immersed in insulating oils, under AC and standard lightning impulse voltages. For comparison purposes, synthetic ester, rape seeds oil (natural ester) and mineral oil were also investigated. Two experimental arrangements were used: (1) a point-to-plane electrodes system where the pressboard is inserted between the electrodes such as the point is perpendicular to pressboard allowing a radial propagation of discharges; and (2) a point-to-bar electrodes system allowing a propagation of discharges in one direction, tangentially to pressboard. The characteristics of discharges propagation, their shape, stopping length (the maximum extension of creeping discharge) as well as the associated current and electrical charge versus the thickness of pressboard and the type of oil are analyzed. It is shown that the magnitude and polarity of voltage, the type of oil as well as the thickness of pressboard influence the characteristics of discharges and especially the stopping length and density of branches. The stopping length of creeping discharges is shorter for pressboard/naturel esters' interfaces than with pressboard/mineral oil interface. [ABSTRACT FROM AUTHOR]

The present work aims at investigating the possibility of mixtures between naphthenic transformer mineral oil (MO) and natural ester olive oil (VO). Ten mixture ratios between the two non-inhibited oils have been constituted. The variations of the electrical and physicochemical checking parameters (density, color number, water content, acidity, breakdown voltage and dissipation factor) are first analyzed and discussed in comparison with their initial values and those recommended by standards. Then, DC fields are applied during 3000 s and isothermal charging current measurements are made. The two original oils are both uninhibited, new and contain water contents in the limits of their saturation levels. The study reveals a favor for the vegetable oil and mixtures up to 15 % of mineral oil, especially with regard to breakdown voltage and charging current behavior. On the other hand, the addition of VO amounts until 15% improves significantly all the properties of the MO in spite of the high water amounts contained in the base VO. [ABSTRACT FROM AUTHOR]

This article presents the results of the studies on lightning properties of two synthetic ester liquids and mineral oil. The measurements concern the standard lightning impulse voltage at both polarities and a point-to-sphere electrode system representing highly divergent electric field distribution. The studies were based on the IEC 60897 Standard wherein the standard recommendations were extended to include light emission registration using a photomultiplier technique. Comparisons of the lightning impulse breakdown voltages (LIBV), times to breakdown (TtB) and light waveforms were made. The results concerning LIBV and TtB showed that at negative polarity both the esters have almost the same lightning characteristics which are slightly below the characteristics of mineral oil. At positive polarity the results indicated an improvement. Regarding the light emission, the mineral oil tested seemed to be more resistant against the appearance of fast light pulses indicating the intense stepwise propagating discharges. [ABSTRACT FROM AUTHOR]

This paper presents experimental studies of streamer propagation and breakdown in a mineral oil and a synthetic ester liquid under both positive and negative DC voltages. A point-plane electrode configuration with a point tip radius of 10 μm was used. Characteristics of streamer including length, propagation velocity and shape were analysed based on shadowgraph images obtained at a gap distance of 10 mm using a multi-channel ultra-high speed camera. Under positive polarity, the streamers in both liquids propagate in the 2nd mode; the stopping length of the synthetic ester is longer than that of the mineral oil at the same applied voltage level. However there is no obvious streamer propagation (less than 10% of the gap distance) under negative polarity even when the applied voltage approaches to the breakdown voltage; the streamers in both liquids stay in the 1st mode. Breakdown tests at various gaps of 2 mm, 5 mm, 10 mm, 20 mm and 30 mm were also investigated. 50% breakdown voltages of the synthetic ester liquid are lower than those of the mineral oil at all the gap distances investigated under both polarities. [ABSTRACT FROM AUTHOR]

Metal particles, such as copper and iron, not only reduce the breakdown voltage but also accelerate the oxidation of insulating oils. The effects of metal particles on the dielectric properties of mineral and natural ester insulating oils were investigated in this work. The experimental results indicate that the AC and impulse breakdown voltages of the insulating oil decrease with the increase of the size and the quantity of the metal particles. The positive breakdown voltages V b+ of insulating oils decrease moderately in the beginning, while the particles quantity increases to a certain extent, the V b+ decreases significantly. In comparison, the metal particles always reduce the negative impulse breakdown voltage V b− significantly. The effect of the copper particles on the insulating oils is slightly greater than that of the iron particles due to their higher conductivity. The permittivity of contaminated insulating oils increases quasi-linearly with the concentration of copper particles. Improved models considering the polarization of the surface oxidation layer of copper particles were proposed, and the calculated data were in good agreement with the measured permittivity of the contaminated insulating oil. [ABSTRACT FROM AUTHOR]