Search

Printed electronic paper identifies its interest in flexible organic electronics and sustainable and clean energy applications because of its straightforward production method, cost‐effectiveness, and positive environmental impact. However, current limitations include restricted material thickness and the use of supporting substrate for printing. Here, 2D and 3D electronic patterned paper are fabricated from direct ink writing (DIW) nanocellulose and PEDOT:PSS‐based materials using syringe deposition and 3D printing. The conductor patterns are integrated in the bulk of the paper, while non‐conductive sections are used as support to form free‐standing paper. The strong interface between the patterns of electronic patterned paper gives mechanical stability for practical handling. The conductive paper‐based electrode has 202 S cm−1 and is capable of handling electric current up to 0.7 A, which can be used for high‐power devices. Printed supercapacitor papers show high specific energy of 4.05 Wh kg−1, specific power of 4615 W kg−1 at 0.06 A g−1, and capacitance retention above 95% after 2000 cycles. The new design structure of electronic patterned papers presents a solution for additive manufacturing of paper‐based composites for supercapacitors, wearable electronics, or sensors for smart packaging. [ABSTRACT FROM AUTHOR]

Organic light-emitting electrochemical cells (LEC) are promising for lighting applications but in many cases these devices suffer from unbalanced electrochemical doping, which cause instability and degradation of the cells. A predominant p-doping over n-doping causes an off-centered emissive p–n junction, which leads to poor power-conversion efficiency. Here, we report a half-gate LEC transistor (HG-LECT), in which an ion-conductive gate made from poly(3,4-ethylenedioxythiophene)-poly-(styrenesulfonate) is employed to combat this instability problem. The gate material, covering half of the channel, is used to enhance the n-doping process in this part by employing an appropriate operation protocol. We demonstrate a centered light emission zone, closely following the geometry of the gate configuration. The HG-LECT with centered emission profile is shown to be more efficient than the corresponding LEC without the gate electrode, and its n-doping level is measured to be 15%. [ABSTRACT FROM AUTHOR]

Abstract: An electrochemical circuit to record time–temperature history has been realized by using the propagation of over-oxidation fronts in stripes of poly(3,4-ethylenedioxythiopehene) blended with poly(styrenesulfonate) (PEDOT:PSS). The over-oxidation front propagation has been characterized and related to the phase change of polyethylene glycol (PEG) electrolytes. The electrolytes were chosen to have a phase transition in the temperature interval to be monitored, resulting in large conductivity variations and thereby an easily interpreted output. A demonstrator has been fabricated and shown to detect a temperature increase and a following temperature decrease. This very simple device is cheap to produce and could be used to monitor the temperature of packages. [ABSTRACT FROM AUTHOR]

The nature of mass transport in plants has recently inspired the development of low-cost and sustainable wood-based electronics. Herein, we report a wood electrochemical transistor (WECT) where all three electrodes are fully made of conductive wood (CW). The CW is prepared using a two-step strategy of wood delignification followed by wood amalgamation with a mixed electron-ion conducting polymer, poly(3,4-ethylenedioxythiophene)-polystyrene sulfonate (PEDOT:PSS). The modified wood has an electrical conductivity of up to 69 Sm-1 induced by the formation of PEDOT:PSS microstructures inside the wood 3D scaffold. CW is then used to fabricate the WECT, which is capable of modulating an electrical current in a porous and thick transistor channel (1 mm) with an on/off ratio of 50. The device shows a good response to gate voltage modulation and exhibits dynamic switching properties similar to those of an organic electrochemical transistor. This wood-based device and the proposed working principle demonstrate the possibility to incorporate active electronic functionality into the wood, suggesting different types of bio-based electronic devices. [ABSTRACT FROM AUTHOR]

Low weight, small footprint, and high performances are essential requisites for the implementation of energy storage devices within consumer electronics. One way to achieve these goals is to increase the thickness of the active material layer. In this work, carbonized and graphitized rayon felt, a cellulose‐derived material, is used as a three‐dimensional current collector scaffold to enable the incorporation of large amount of active energy storage materials and ionic liquid‐based gel electrolyte in the supercapacitor devices. PEDOT:PSS, alone or in combination with active carbon, has been used as the active material. Three‐dimensional supercapacitors with high per unit area capacitance (more than 1.1 F/cm2) have been achieved owing to the loading of large amount of active material in the felt matrix. Areal energy density of more than 101 μWh/cm2 and areal power density of more than 5.9 mW/cm2 have been achieved for 0.8 V operating voltage at a current density of 1 mA/cm2. A nanographite material was found to be beneficial in reducing the internal serial resistance of the supercapacitor to lower than 1.7 Ω. Furthermore, it was shown that even after 2000 times cycling test, the devices could still retain its performance with at least 88% coulombic efficiency for all the devices. All the materials are readily available commercially, environmentally sustainable and the process can potentially be upscaled with industrial process. [ABSTRACT FROM AUTHOR]

Organic electronic circuits based on organic electrochemical transistors (OECTs) are attracting great attention due to their printability, flexibility, and low voltage operation. Inverters are the building blocks of digital logic circuits (e.g., NAND gates) and analog circuits (e.g., amplifiers). However, utilizing OECTs in electronic logic circuits is challenging due to the resulting low voltage gain and low output voltage levels. Hence, inverters capable of operating at relatively low supply voltages, yet offering high voltage gain and larger output voltage windows than the respective input voltage window are desired. Herein, inverters realized from poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate‐based OECTs are designed and explored, resulting in logic inverters exhibiting high voltage gains, enlarged output voltage windows, and tunable switching points. The inverter designs are based on multiple screen‐printed OECTs and a resistor ladder, where one OECT is the driving transistor while one or two additional OECTs are used as variable resistors in the resistor ladder. The inverters' performances are investigated in terms of voltage gain, output voltage levels, and switching point. Inverters, operating at +/−2.5 V supply voltage and an input voltage window of 1 V, that can achieve an output voltage window with ∼110% increment and a voltage gain up to 42 are demonstrated. [ABSTRACT FROM AUTHOR]

Low‐voltage operating organic electronic circuits with long‐term stability characteristics are receiving increasing attention because of the growing demands for power efficient electronics in Internet of Things applications. To realize such circuits, inverters, the fundamental constituents of many circuits, with stable transfer characteristics should be designed to provide low‐power consumption. Here, a rational inverter design, based on fully screen printed p‐type organic electrochemical transistors with a channel size of 150 × 80 µm2, is explored for driving conditions with input voltage levels that differs of about 1 V. Further, three different inverter circuits are explored, including resistor ladders with resistor values ranging from tens of kΩ to a few MΩ. The performance of single inverters, 3‐stage cascaded inverters and 3‐stage ring oscillators are characterized with respect to output voltage levels, propagation delay, static power consumption, voltage gain, and operational frequency window. Depending on the application, the key performance parameters of the inverter can be optimized by the specific combination of the input voltage levels and the resistor ladder values. A few of the inverters are in fact fully functional up to 30 Hz, even when using input voltage levels as low as (0 V, 1 V). [ABSTRACT FROM AUTHOR]

Abstract: Poly(3,4-ethylenedioxythiophene) chemically doped with poly(styrene sulfonic acid) (PEDOT:PSS) is a material system commonly used as a conductive and transparent coating in several important electronic applications. The material is also electrochemically active and exhibits electrochromic (EC) properties making it suitable as the active element in EC display applications. In this work uniformly coated PEDOT:PSS layers were used both as the pixel electrode and as the counter electrode in EC display components. The pixel and counter electrodes were separated by a whitish opaque and water-based polyelectrolyte and the thicknesses of the two EC layers were varied independently in order to optimize the color contrast of the display element. A color contrast (ΔE ∗, CIE L ∗ a ∗ b ∗ color space) exceeding 40 was obtained with maintained relatively short switching time at an operational voltage less than 2V. [Copyright &y& Elsevier]

Abstract The conductive polymer poly(3,4-ethylenedioxythiphene):poly(styrenesulfonate) (PEDOT:PSS) is widely used in organic electronics and printed electronics due to its excellent electronic and ionic conductivity. PEDOT:PSS films exhibit anisotropic conductivities originating from the interplay of film deposition processes and chemical structure. The previous studies found that high boiling point solvent treated PEDOT:PSS exhibits an anisotropy of 3–4 orders magnitude. Even though both the in-plane and out-of-plane conductivities are important for the device performance, the out-of-plane conductivity is rarely studied due to the complexity with the experiment procedure. Cellulose-based paper or films can also exhibit anisotropic behavior due to the combination of their intrinsic fibric structure and film formation process. We have previously developed a conductive paper based on PEDOT:PSS and cellulose which could be used as the electrodes in energy storage devices. In this work we developed a novel measurement set-up for studying the anisotropy of the charge transport in such composite materials. A tool with two parallel plates mounted with spring loaded probes was constructed enabling probing both lateral and vertical directions and resistances from in-plane and out-of-plane directions to be obtained. The measurement results were then input and analyzed with a model based on a transformation method developed by Montgomery, and thus the in-plane and out-of-plane conductivities could be detangled and derived. We also investigated how the conductivity anisotropy depends on the microstructure of the cellulose template onto which the conductive polymer self-organizes. We show that there is a relatively small difference between the in-plane and out-of-plane conductivities which is attributed to the unique 3D-structure of the composites. This new knowledge gives a better understanding of the possibilities and limitations for using the material in electronic and electrochemical devices. Graphical abstract Image 1 Highlights • Developed a simple to use generic tool for measuring 3-D resistances of thick conducting self-standing films. • The in-plane and out-of-plane conductivities were deduced by a method developed by Montgomery. • Both CNF-PEDOT:PSS and pulp-PEDOT:PSS films exhibit anisotropic conductivity. • CNF-PEDOT:PSS films show thickness independent anisotropic conductivity. • Pulp-PEDOT:PSS became less anisotropic with increasing thicknesses. [ABSTRACT FROM AUTHOR]