Search

In this paper, a submillimetric/THz metasurface polarization/oblique independent absorber is designed and characterized. The absorber is designed using a periodic arrangement of a modified split ring resonator unit cell. The symmetric absorber is insensitive to the variation of incident angles and polarization angles. The results confirm that perfect absorption is achieved (close to 100%) for either TM or TE polarization at 300 GHz. Moreover, the absorber is efficient for normal and oblique incident angle (above 90% for 45° angle of incidence). In all the presented cases, the full width half maximum bandwidth is 20 GHz. The absorber unit cell size is only 0.0052 λ0 × 0.0052 λ0 and it has a low-profile thickness = 0.0002 λ0, at the operating frequency. Also, an absorber-based biosensor is presented. The sensing has proved the coating analyte thickness can be detected by shifting the absorption frequency. The maximum sensitivity is 24.9% RIU−1 with a low-profile maximum of 50 µm thickness. Analytical formulas for the frequency shift have been extracted. The presented results are discussed based on 3D full-wave EM simulations. [ABSTRACT FROM AUTHOR]

This paper presents a new diplexer design of a new-coupled composite right/left-handed (CRLH) resonator to serve the LTE applications. The realization of the diplexer is designed as coupled two zeroth order π-CRLH resonators to represent with zero electrical length and hence attaining a significant size reduction. The filters are designed to achieve a desired frequency bandwidth of 4% ∼16.7 Q-factor and ∼0.066 coupling coefficient at a centre frequency of 2.1 and 2.6 GHz with transmission zeros. The diplexer exhibits a rejection level of 15–20 dB while maintaining insertion loss of 1 dB for the Tx and Rx bands. The circuit design concepts are verified using equivalent circuit simulations, full electromagnetic simulations and experimental measurements. In conclusion, a good agreement is perceived between the measured and simulated data with size compactness of 30 × 60 mm2. [ABSTRACT FROM AUTHOR]

A compact low-loss microstrip diplexer with four controllable transmission zeros (TZs), all less than 41 dB, is presented. The diplexer circuit consists of two coupled gap bandpass filters with a T-junction as a combining circuit. Channels' filters metalize SIW resonators loaded with metamaterial cells operated at zeroth order mode for compactness and low loss operation. For each channel, a fractional bandwidth of 1.9% is obtained. Also, two TZs at both sides of the resonant frequency are obtained by mixed electric and magnetic coupling between channels' resonators. Design methodology for filtering response and placing TZs at certain frequencies are discussed in detail. There is a good agreement between simulation and measurement with isolation better than 40 dB. Moreover, the diplexer has a small size of (1.1×1.43 λg2). Lower and higher TZs are located at 4.75 and 5.69 GHz, for the lower channel, and at 5.4 GHz and 6.2 GHz for the higher channel, respectively. [ABSTRACT FROM AUTHOR]

Proposed in this paper is a new configuration for a quad-band antenna based on using a metamaterial-inspired defected ground structure. The presented structure is introduced as a new modified metamaterial Complementary Split Ring Resonator (CSRR) with a compact electrical size. The new modified CSRR has been employed in Composite Right/Left-Handed (CRLH) transmission line configuration for ultra-size reduction. Validation for the particle small size is introduced and the detailed analysis for the NRI characteristics has been discussed by extracting the cell constitutive parameters. Hence, a multi-band antenna is designed based on using only one cell of the proposed NRI-TL. Subsequently, a small multi-band antenna is presented for different multi-band functionalities and different radiation properties. The antenna displays quad-resonances at 1.78 GHz, with the typical omnidirectional radiation pattern, 3.28 GHz, 4 GHz, and 4.3 GHz, with the directive broadside radiation properties. The proposed antenna footprint is 10 × 10 cm2, which exhibits a size reduction of up to 80% in comparison with a rectangular patch antenna operating at the lowest frequency band. [ABSTRACT FROM AUTHOR]

In this paper, a novel high power high selective and high-Q packaged dual band air suspended stripline notch filter is presented. The notch frequencies, at 2.4 and 3.5 GHz, were designed using defected suspended stripline (DSS). Moreover, the filter was packaged and shielded using perfect magnetic conductor (PMC). The DSS were designed using two frequency independent non-coupled cascaded U shape resonators. It has been proved that the filter attenuation has a sharp rejection characteristic (measured) at the two resonance frequencies (27 dB at 2.4 GHz) and (30 dB at 3.5 GHz) with Quality factor = (18). So, the sharp measured filter attenuation performance was further enhanced to become 38 dB at the two frequencies. The achieved results are discussed and confirmed using different circuit, 3D EM and experimental measurements. The designed filter can find many medium powers up to 20 kW applications. [ABSTRACT FROM AUTHOR]

In this paper, a compact novel simple design of ultra‐wide bandpass filter with high out of band attenuation is presented. The filter configuration is based on combining an ultra‐wide band composite right/left‐handed (CRLH) band pass filter (BPF) with simple uni‐planar configuration of complementary split ring resonator (UP‐CSRR). By integrating two UP‐CSRR cells, the ultra‐wideband CRLH filter roll‐off and wide stopband attenuation are enhanced. The filter has 3 dB cutoff frequencies at 3.1 GHz and 10.6 GHz with insertion loss equals 0.7 dB in average and minimum and maximum values of 0.48 dB and 1.05 dB, respectively over the filter passband. Within the passband. The transition band attenuation from 3 dB to 20 dB is achieved within the frequency band 1.9 GHz to 3.1 GHz (48%) at lower cutoff and the frequency band 10.6 GHz to 11.4 GHz (7%) at upper stopband. Moreover, the filter has a wide stopband attenuation >20 dB in frequencies 11 GHz to 13.6 GHz (21%) and ends with 3 dB cutoff frequency at 14.8 GHz. Furthermore, the designed filter size is very compact (23 × 12 mm2) whose length is only about 0.17 λg at 6.85 GHz. The filter performance is examined using circuit modeling, full‐wave simulations, and experimental measurements with good matching between all of them. [ABSTRACT FROM AUTHOR]

ABSTRACT This study presents the design of an electrically small metamaterial antenna with dual-band characteristics for WLAN and WiMAX applications with coplanar ground. The proposed antenna consists of stepped-impedance closed ring resonator (SICRR) and a small rectangular patch which is designed by etching a split ring resonator (SRR) from a rectangular patch which is turn fed through main feed. Such metamaterial composite exhibits dual-band behavior with first band operating at 2.45 GHz with an impedance bandwidth (| S11| < −10 dB) of 8.16% while second band is resonant at 3.37 GHz having an impedance bandwidth of 23.74% respectively. The proposed antenna is designed specifically to operate at WLAN (2.5 GHz) and WiMAX (3.5 GHz) and shows compact nature with a radiating element size of 0.16λo × 0.097λo × 0.013λo. Equivalent circuit of proposed antenna has also been modeled which is in good agreement with the antenna behavior. The proposed structure shows end fire radiation pattern in H-plane and omni-directional radiation pattern in E-plane at all operating frequencies with low cross polarization levels. The prototype has been fabricated and experimentally tested to validate the simulation results which are in good agreement with the measured results. The antenna is suitable for use in Bluetooth, WLAN and WiMAX. © 2017 Wiley Periodicals, Inc. Microwave Opt Technol Lett 59:573-578, 2017 [ABSTRACT FROM AUTHOR]

The theoretical study and experimental results of a compact tunable left-handed (LH) zeroth order metamaterial ferrite resonator is presented. The resonator has been designed and realised using a LH coplanar waveguide transmission line on a ferrite substrate. The theoretical analysis of the operation principles of the resonator has been provided. The detailed measurement setup and experimental results are discussed. The resonator is only 0.19 λg (65% reduced in size comparing with conventional one) at 4 GHz. The resonator has fractional bandwidth of 0.1% and average insertion loss, approximately 4.5 dB. Moreover, the zeroth order metamaterial ferrite resonator has tuning capability and requires lower DC magnetic bias. [ABSTRACT FROM AUTHOR]

This study presents the design of switching techniques for dual-notched ultra-wideband antenna. The dual bandnotched frequencies are achieved by using switched defected microstrip structure band stop filter inserted in the microstrip feed line and a switched meandered slot etched in the radiation patch. The switching reconfiguration is accomplished by combining the two ideal switches to introduce a notch filter response to prevent the interference to the primary users operating in the middle and upper WiMAX wireless local area network bands. The proposed structure has four modes by controlling the two switches on and off. The proposed antenna has good matched impedance from 2.5 to 12 GHz with two notched bands from 3.3 to 3.8 GHz (middle WiMAX applications) and from 5.1 to 5.9 GHz (upper WiMAX applications). The antenna is fabricated and tested. Good agreement is achieved between the simulated and measured results. [ABSTRACT FROM AUTHOR]