Search

For the study of high-temperature superconductors and for the application of superconductivity, a superconducting high-field magnetization system with a hybrid superconducting coil was designed. This coil is composed of superconducting wires of three kinds—HTS YBCO 2G-wire, high-field and low-field NbTi wires. Three principal purposes of building this system are to inspect the characteristics of disk-shape bulk YBCO, to develop a HTS-bulk undulator, and to magnetize a portable HTS-bulk high-field magnet for application to a resonant X-ray scattering experiment. With four steps of temperature decrease, a two-stage GM-type cryocooler and liquid nitrogen provide cooling for the magnetization system. The hybrid superconducting coil, two cryogenic systems for the magnetization system and the portable HTS-bulk magnet, and the control and monitor systems that were designed are discussed. [ABSTRACT FROM PUBLISHER]

A 130-pole superconducting undulator with NbTi wires was wound and tested at National Synchrotron Radiation Research Center (NSRRC). The magnetic field was measured with a cryogenic mini-Hall sensor in a vertical dewar. The difference of total length between the nominal design and that measured experimentally with the Hall probe is approximately 1.2 mm; this discrepancy arises from the thermal contribution during the field measurement in the test dewar. The reliability of the measurement system is confirmed, and is discussed in terms of the field-mapping spectrum. The measurement of the field strength revealed a non-uniform distribution of the field in the 1 m long arrays. An iron pole piece was used to shim the on-axis field strength of the undulators. We discuss the thermal effect of the measurement system, a useful shimming method and its results for the superconducting undulator. [ABSTRACT FROM AUTHOR]

The wire windings and magnetic performance of the mini-pole superconducting undulator (SCU) at the National Synchrotron Radiation Research Center (NSRRC) are being improved. NbTi superconducting (SC) wire with a rectangular cross section 0.51 mm x 0.77 mm was wound on a racetrack iron pole. The designed field strength was 1.4 T at excitation current 510 A. The bath LHe-cryostat cools the SC wire directly and uniformly using LHe. A stainless-steel (SS) beam duct (thickness 0.3 mm) is designed to separate the ultra-high vacuum (UHV) from the storage ring and the LHe. The SS beam duct is glued to the dummy arrays with resin epoxy. The dummy arrays provide a strong support for the beam duct, providing against deformity from a pressure differential. A vacuum test was performed with a short version of a beam duct (length 400 mm) at low temperature. This paper describes the construction of the magnet, the measurement of the field and the testing of the SS beam duct. [ABSTRACT FROM AUTHOR]

A cryogen-free cryostat for a superconducting undulator with a period of 15 mm (SU15) was developed at the National Synchrotron Radiation Research Center (NSRRC). A 0.44 mm-thin superconducting NbTi wire was wound on iron pole with a racetrack profile. The design field strength of SU15 was 1.4 T and the coil had 148 turns/pole at 230 A; the magnet gap was 5.6 mm. The liquid helium (LHe) recondensation cryostat was designed for SU15. The cryostat provides the advantage of uniform cooling and reduces the amount of LHe consumed. A 0.3 mm-thick stainless steel (SS) beam duct was formed to separate the vacuum in the storage ring from the magnet. Therefore, all of dirty material is produced out of storage ring vacuum. Most of the heat leaked from the LHe vessel leaks from the LHe-fill port heat leak and the 300 K-4.2 K beam duct or was associated with image current power dissipation (ICPD) and bending magnet power dispersion (BMPD). The leaking of heat from the main coil was prevented by the high-temperature superconducting current leads (HTSC). The beam duct was coated with a copper layer with a high-RRR ratio to reduce image current heating. The heat loads on the magnet were cooled using two 1.5 W Gifford-MacMahon (GM) type cryocoolers via LHe medium. [ABSTRACT FROM AUTHOR]

A mini-pole planar vertically-wound racetrack coil undulator was studied to determine its potential for use as a hard X-ray source in a 3 GeV storage ring. A field strength of 1.4 T can be obtained for a superconducting undulator with a periodic length of 1.5 cm and a fixed magnetic gap of 5.6 mm. The magnetic circuit was optimized and a current density of 1090 A/mm², at 80% of the critical current, meets the field strength requirement. A prototype with 40 poles was constructed to verify the design of the magnet and the performance of NbTi superconductor. Additionally, the magnetic field shimming method was developed for spectrum shimming. This study discusses the design of the magnetic circuit and the structure of the magnetic array, the field shimming technique, and the test results of the prototype magnet. [ABSTRACT FROM AUTHOR]