Search

The technology of high temperature drying has a great influence on dimensional and selected physical changes in tension wood. Article is focused on the measurement properties such as moisture content, color changes and longitudinal warping. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative alterations in solid wood quality and limits industrial application of wood. The different values of longitudinal warping which were measured after drying were higher in tension wood than in normal wood. Impact of radial and tangential angle of growth rings is non-significant factor.

The article presents the impact of drying process and selected parameters on the color changes on the surface of pine wood (Pinus sylvestris L.). Three predetermined process conditions (modes), mild, normal, and intensive, were investigated. The experiments were conducted using a semi-industrial scale dryer designed at the Gdańsk University of Technology with a loading capacity of 0.55 m3. The drying process was applied to pine wood grown in the northern part of Pomeranian region in Poland. The specimens were selected taking into consideration the radial angle of the growth rings. During each drying mode, 25 pieces of wood with dimensions (thickness, width, length) of 0.03 m, 0.2 m, and 1.5 m, respectively, were dried. The total color change (E) after drying process and color saturation (h*) before and after drying processes of the wood surface was determined using the normalized CIELAB methods. The obtained results indicated that the color change of the pine wood surface increased simultaneously with the intensification of the drying process. However, the normalized wood quality after drying under intensive drying process conditions remained within the standard limits. The application of intensive drying process conditions remarkably changes the surface color of the obtained material, while remarkably reducing the drying process duration. [ABSTRACT FROM AUTHOR]

Industrial buildings from the beginning of the 20th century can still be found in Polish cities. Some of them have already been listed as heritage objects. Those structures where new technical solutions and materials were used, for example concrete, are especially interesting. Some of those objects are currently under a process of restoration with the aim to reconstruct and adapt them for completely new and different utility functions but without losing their important heritage value. In this paper, elements of the assessment procedure of the technical state regarding a historical survey, material examination and structural analysis, are presented on the example of two selected industrial buildings in which reinforced concrete was used as the main structural material. The main aim of the performed diagnostic procedure was verification of the load-bearing capacity of structures of the examined buildings. The calculation made confirmed that in case of not damaged concrete elements they have enough capacity to carry on newly designed loads. That confirmed that old concrete structures, especially in industrial buildings, sometimes have capacity reserves. On the other hand it allows to perform the design of less invasive renovation works or strengthening solutions with the aim to respect their industrial heritage value.

The thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded. Color changes apply not only to natural wood, but also to such wood composites for which some amount of glue is used in their construction (e.g., plywood, blockboard or laminboard). This article is focused on the analysis of hornbeam and field maple wood color changes influenced by drying temperature. Two types of drying modes were used: hot-air mode where the temperature of the drying environment was 60 °C, and high-temperature mode with a drying temperature of 120 °C. The drying mode was divided into two phases depending on the moisture content of the wood. The compared woods had similar values of color coordinates at the beginning of drying. During hot-air drying, the largest changes in color coordinates occurred during the first 24 h. The total color difference between the color at the end and the beginning of drying was 7.3 for hornbeam and 11.1 for maple. The overall color difference between the compared woods was minimal. During high-temperature drying (120 °C), the color changes of the dried woods were more pronounced. In the case of maple wood, there was a very significant change in color and the value of ΔE* was twice as high as for hornbeam. The total color difference between the color at the end and at the beginning of drying was 8.7 for hornbeam and 18.9 for maple. [ABSTRACT FROM AUTHOR]

This study examined the changes in the properties of beech wood (Fagus sylvatica L.) after intense drying. Beech wood with false red heartwood was selected as the test specimen. The test samples had dimensions of 50 mm thickness, 180 mm width, and 350 mm length. The specimens were divided into two groups, false red heartwood and sapwood. These specimens were selected with different angles of the growth rings (radial and tangential). The results showed that samples with red heartwood, in comparison to samples with sapwood content, had a remarkable effect in covering. Observation of specimens with false red heartwood and sapwood before and after drying process revealed significant differences in color changes and measured values during the covering-slicing test, but not between samples with different growth ring angles. [ABSTRACT FROM AUTHOR]

Several properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine (Pinus sylvestris L.) wood from different provinces in Poland with varying densities were machined on a sash gang saw. The average cutting force versus average wood density (estimated with the standard gravimetric method) was calculated, and the local cutting forces correlated to the local wood density. The average values of the cutting forces measured at selected points along the sample's length were calculated by linear regression to the X-ray absorbance (density) estimated by means of X-ray radiography. [ABSTRACT FROM AUTHOR]

The influence of the impregnation process of pine wood (Pinus sylvestris L.) samples on the electrical resistance changes and the moisture-content measurement accuracy is presented in this paper. In this study, the resistances of impregnated and nonimpregnated green pine timber harvested from northern Poland were compared. An impregnation method based on a vacuum-pressure chamber was used. Copper salts were applied as the impregnated solutions. The obtained results of the electrical resistance comparison showed a dependence of wood resistance on the moisture content. Higher conductivity occurred in impregnated wood samples filled with copper salt compared with wood samples without impregnation. Noticeable differences in the electrical resistance values were observed when the wood moisture content was significantly above the Fibre Saturation Point (FSP). [ABSTRACT FROM AUTHOR]