Search

Diffusional limitations associated with zeolite microporous systems can be overcome by developing hierarchical zeolites, i.e., materials with a micro- and mesoporous framework. In this work, Y and ZSM-5 zeolites were modified using a surfactant-mediated hydrothermal alkaline method, with NaOH and cetyltrimethylammonium bromide (CTAB). For Y zeolite, after a mild acidic pretreatment, the effect of the NaOH+CTAB treatment time was investigated. For ZSM-5 zeolite, different concentrations of the base and acid solutions were tested in the two-step pretreatment preceding the hydrothermal treatment. The properties of the materials were studied with different physical–chemical techniques. Hierarchical Y zeolites were characterized by 3.3–5 nm pores formed during the alkaline treatment through the structure reconstruction around the surfactant aggregates. The effectiveness of the NaOH+CTAB treatment was highly dependent on the duration. For intermediate treatment times (6–12 h), both smaller and larger mesopores were also obtained. Hierarchical ZSM-5 zeolites showed a disordered mesoporosity, mainly resulting from the pretreatment rather than from the subsequent hydrothermal treatment. High mesoporosity was obtained when the concentration of the pretreating base solution was sufficiently high and that of the acid one was not excessive. Hierarchical materials can be obtained for both zeolite structures, but the pretreatment and treatment conditions must be tailored to the starting zeolite and the desired type of mesoporosity. [ABSTRACT FROM AUTHOR]

The potential of aerogels as catalysts for the synthesis of a relevant class of bis-heterocyclic compounds such as bis(indolyl)methanes was investigated. In particular, the studied catalyst was a nanocomposite aerogel based on nanocrystalline nickel ferrite (NiFe2O4) dispersed on amorphous porous silica aerogel obtained by two-step sol–gel synthesis followed by gel drying under supercritical conditions and calcination treatments. It was found that the NiFe2O4/SiO2 aerogel is an active catalyst for the selected reaction, enabling high conversions at room temperature, and it proved to be active for three repeated runs. The catalytic activity can be ascribed to both the textural and acidic features of the silica matrix and of the nanocrystalline ferrite. In addition, ferrite nanocrystals provide functionality for magnetic recovery of the catalyst from the crude mixture, enabling time-effective separation from the reaction environment. Evidence of the retention of species involved in the reaction into the catalyst is also pointed out, likely due to the porosity of the aerogel together with the affinity of some species towards the silica matrix. Our work contributes to the study of aerogels as catalysts for organic reactions by demonstrating their potential as well as limitations for the room-temperature synthesis of bis(indolyl)methanes. [ABSTRACT FROM AUTHOR]

Nanoporous (NP) gold, the most extensively studied and efficient NP metal, possesses exceptional properties that make it highly attractive for advanced technological applications. Notably, its remarkable catalytic properties in various significant reactions hold enormous potential. However, the exploration of its catalytic activity in the degradation of water pollutants remains limited. Nevertheless, previous research has reported the catalytic activity of NP Au in the degradation of methyl orange (MO), a toxic azo dye commonly found in water. This study aims to investigate the behavior of nanoporous gold in MO solutions using UV-Vis absorption spectroscopy and high-performance liquid chromatography. The NP Au was prepared by chemical removal of silver atoms of an AuAg precursor alloy prepared by ball milling. Immersion tests were conducted on both pellets and powders of NP Au, followed by examination of the residual solutions. Additionally, X-ray photoelectron spectroscopy and electrochemical impedance measurements were employed to analyze NP Au after the tests. The findings reveal that the predominant and faster process involves the partially reversible adsorption of MO onto NP Au, while the catalytic degradation of the dye plays a secondary and slower role in this system. [ABSTRACT FROM AUTHOR]

A series of multicomponent oxide catalysts (CuO/ZnO/MemOn/ZrO2/SiO2, with Me = Mg, Ce, or La) was synthesized through a one-pot soft-template approach and used for CO2 hydrogenation to methanol. In the case of the La-containing catalysts, additional samples were prepared with CuO contents in the range 40–60 wt%. The influence of the catalyst composition on the physicochemical properties as well as the effect on the catalytic performance were investigated. The fresh catalysts were characterized in terms of composition, structure, textural properties, dispersion of the oxidic phases, and reducibility. On the reduced samples, structural and acid–base properties were also investigated, as well as specific metal surface area and dispersion of Cu0. After in situ H2-treatment at 250 °C, the catalysts activity was tested in a bench scale plant at 250 °C and 3.0 MPa, using a gas hourly space velocity of 24,000 Ncm3 h−1 gcat−1 and a H2/CO2 molar ratio equal to 3. It was found that the production of methanol is particularly favored by the introduction of La2O3, the highest value of methanol space–time yield (413 mg CH 3 OH h - 1 g cat - 1 ) being obtained on the CuO/ZnO/La2O3/ZrO2/SiO2 catalyst containing 50 wt% of copper oxide. [ABSTRACT FROM AUTHOR]

Functionalized aluminosilicate materials were studied as catalysts for the conversion of different cyclic carbonates to the corresponding epoxides by the addition of CO2. Aluminum was incorporated in the mesostructured SBA-15 silica network. Thereafter, functionalization with imidazolium chloride or magnesium oxide was performed on the Al_SBA-15 supports. The isomorphic substitution of Si with Al and the resulting acidity of the supports were investigated via 27Al magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy and NH3 adsorption microcalorimetry. The Al content and the amount of MgO were quantified via inductively coupled plasma optical emission spectroscopy (ICP-OES) analysis. The anchoring of the imidazolium salt was assessed by 29Si and 13C MAS NMR spectroscopy and quantified by combustion chemical analysis. Textural and structural properties of supports and catalysts were studied by N2 physisorption and X-ray diffraction (XRD). The functionalized systems were then tested as catalysts for the conversion of CO2 and epoxides to cyclic carbonates in a batch reactor at 100 or 125 °C, with an initial CO2 pressure (at room temperature) of 25 bar. Whereas the activity of the MgO/xAl_SBA-15 systems was moderate for the conversion of glycidol to the corresponding cyclic carbonate, the Al_SBA-15-supported imidazolium chloride catalysts gave excellent results over different epoxides (conversion of glycidol, epichlorohydrin, and styrene oxide up to 89%, 78%, and 18%, respectively). Reusability tests were also performed. Even when some deactivation from one run to the other was observed, a comparison with the literature showed the Al-containing imidazolium systems to be promising catalysts. The fully heterogeneous nature of the present catalysts, where the inorganic support on which the imidazolium species are immobilized also contains the Lewis acid sites, gives them a further advantage with respect to most of the catalytic systems reported in the literature so far. [ABSTRACT FROM AUTHOR]

Copper-based nanoparticles, supported on either a silica aerogel or cubic mesostructured silicas obtained by using two different synthetic protocols, were used as catalysts for the water gas shift reaction. The obtained nanocomposites were thoroughly characterised before and after catalysis through nitrogen adsorption-desorption measurements at −196 °C, TEM, and wide- and low-angle XRD. The samples before catalysis contained nanoparticles of copper oxides (either CuO or Cu2O), whereas the formation of metallic copper nanoparticles, constituting the active catalytic phase, was observed either by using pre-treatment in a reducing atmosphere or directly during the catalytic reaction owing to the presence of carbon monoxide. A key role in determining the catalytic performances of the samples is played by the ability of different matrices to promote a high dispersion of copper metal nanoparticles. The best catalytic performances are obtained with the aerogel sample, which also exhibits constant carbon monoxide conversion values at constant temperature and reproducible behaviour after subsequent catalytic runs. On the other hand, in the catalysts based on cubic mesostructured silica, the detrimental effects related to sintering of copper nanoparticles are avoided only on the silica support, which is able to produce a reasonable dispersion of the copper nanophase. [ABSTRACT FROM AUTHOR]

Zinc oxide/ and iron oxide/SBA-15 composites were synthesized using the innovative Two-Solvents procedure and tested as sorbents for the mid-temperature (300 °C) removal of hydrogen sulphide, and then compared with a commercial unsupported ZnO sorbent. The sulphur retention capacity results showed the superior performance of the iron oxide/SBA-15 composite (401 mg S g−1 Fe2O3) in comparison with the zinc oxide/SBA-15 composite (53 mg S g−1 ZnO), both these sorbents being much more efficient than the commercial sorbent (6 mg S g−1 ZnO). The different sorption behaviour was discussed in terms of the nature of the nanocomposites where: (i) the mesostructure of the support was retained with a high surface area and pore volume; (ii) the zinc oxide phase was incorporated inside the SBA-15 channels as a thin amorphous homogeneous layer while the iron oxide was dispersed in form of small maghemite crystallites; and (iii) significant interactions occurred between the silica matrix and the zinc oxide phase. Remarkable differences in the regeneration behaviour of the exhaust sorbents were revealed by temperature-programmed experiments under an oxidizing atmosphere. After regeneration, the sorption properties of the zinc oxide/SBA-15 composite appeared to be enhanced compared to the commercial sorbent. Incomplete recovery of the sorption activity was observed for the regenerated iron oxide/SBA-15 sorbent, whose performance remained far better than that of the ZnO-based one, either fresh or regenerated. In view of its higher sulphur retention capacity and appropriate regeneration temperature (T≤ 350 °C), the iron oxide/SBA-15 composite is a promising material for the design of advanced sorbents for a thermally efficient H2S removal process from hot gas streams. [ABSTRACT FROM AUTHOR]

In this study, CeO2, La2O3, and CeO2-La2O3 mixed oxide catalysts with different Ce/La molar ratios were prepared by the soft template method and characterized by different techniques, including inductively coupled plasma atomic emission spectrometry, X-ray diffraction, N2 physisorption, thermogravimetric analysis, and Raman and Fourier transform infrared spectroscopies. NH3 and CO2 adsorption microcalorimetry was also used for assessing the acid and base surface properties, respectively. The behavior of the oxides as catalysts for the dimethyl carbonate synthesis by the transesterification of propylene carbonate with methanol, at 160 °C under autogenic pressure, was studied in a stainless-steel batch reactor. The activity of the catalysts was found to increase with an increase in the basic sites density. The formation of dimethyl carbonate was favored on medium-strength and weak basic sites, while it underwent decomposition on the strong ones. Several parasitic reactions occurred during the transformation of propylene carbonate, depending on the basic and acidic features of the catalysts. A reaction pathway has been proposed on the basis of the components identified in the reaction mixture. [ABSTRACT FROM AUTHOR]

CO2-derived methanol and dimethyl ether can play a very important role as fuels, energy carriers, and bulk chemicals. Methanol production from CO2 and renewable hydrogen is considered to be one of the most promising pathways to alleviate global warming. In turn, methanol could be subsequently dehydrated into DME; alternatively, one-step CO2 conversion to DME can be obtained by hydrogenation on bifunctional catalysts. In this light, four oxide catalysts with the same Cu and Zn content (Cu/Zn molar ratio = 2) were synthesized by calcining the corresponding CuZnAl LDH systems modified with Zr and/or Ce. The fresh ex-LDH catalysts were characterized in terms of composition, texture, structure, surface acidity and basicity, and reducibility. Structural and acid–base properties were also studied on H2-treated samples, on which specific metal surface area and dispersion of metallic Cu were determined as well. After in situ H2 treatment, the ex-LDH systems were tested as catalysts for the hydrogenation of CO2 to methanol at 250 °C and 3.0 MPa. In the same experimental conditions, CO2 conversion into dimethyl ether was studied on bifunctional catalysts obtained by physically mixing the ex-LDH hydrogenation catalysts with acid ferrierite or ZSM-5 zeolites. For both processes, the effect of the Al/Zr/Ce ratio on the products distribution was investigated. [ABSTRACT FROM AUTHOR]

Supported nickel catalysts were synthesized, characterized, and employed in the carbon oxides co-methanation process. Five NiO/CeO2-ZrO2 mixed oxides, with the same Ni content and different Ce/Zr molar ratios, were prepared by the soft-template method. They were characterized through ICP-AES, N2 adsorption, XRD, and TPR. Reduced Ni/CeO2-ZrO2 catalysts were obtained by submitting the oxide systems to reduction treatment in H2 at 400 °C. They were characterized by XRD, H2-TPD, and CO2 adsorption microcalorimetry and their catalytic performances in the carbon oxides co-methanation were investigated. Catalytic tests were performed in a fixed-bed continuous-flow microreactor at atmospheric pressure. The effect of experimental conditions (reaction temperature, space velocity, reactants molar ratio) was also studied. Almost complete CO conversion was obtained on any catalyst, whereas CO2 conversion was much lower and increased with Ce content, at least up to Ce/Zr = 1. The beneficial effect of the Ce content could be related to the increased NiO reducibility and to the higher ability to adsorb and activate CO2. However, at high Ce/Zr ratios, it is probably counterbalanced by an interplay of reactions involving CO and CO2. [ABSTRACT FROM AUTHOR]