Search

The paper presents a static analysis of the buckling and post-buckling state of thin-walled cold-formed steel (TWCFS) lipped channel section beam-columns subjected to eccentric compression. Eccentricity is taken into consideration relative to both major and minor principal axes. An analytical–numerical solution to the buckling and post-buckling problems is described. The solution is based on the theory of thin plates. Equations of equilibrium of section walls are derived from the principle of stationary energy. Then, to solve the problem, the finite difference (FDM) and Newton–Raphson methods are applied. Linear (buckling) and nonlinear (post-buckling) analyses are performed. As a result, pre- and post-buckling equilibrium paths are determined. Comparisons of the obtained numerical results, FE simulation results, and experimental test results are carried out and presented in comparative load-shortening diagrams. Additionally, a comparison of the buckling forces and buckling modes obtained from theoretical analysis and experiments is presented. [ABSTRACT FROM AUTHOR]

Copyright of Archives of Civil Engineering (Polish Academy of Sciences) is the property of Polish Academy of Sciences and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

A nonlinear problem of deflection of isotropic cylindrical panels fixed along all edges and subject to transverse load was considered within the first-order shear deformation theory (FSDT) and the classical shell theory (CST). An effect of the parameter of curvature on bending and membrane components and resultants of transverse forces was analyzed. Particular attention was drawn to the fact that the bending components were accompanied by transverse deformations, whereas for the membrane components, the panel was transversely perfectly rigid. Resultants of transverse forces can be significantly larger than the bending components. In failure criteria of laminated structures, only the bending transverse forces are employed. [ABSTRACT FROM AUTHOR]

A way of selecting the ceramic coating thickness concerning the axially symmetrical thermal stresses in a casting machine plunger with a horizontal shot sleeve was discussed. Application of a technological ceramic outer layer in the plunger enhances its tribological properties. The condition that stresses in tension in the outer ceramic layer are lower than the tensile strength was proposed as a selection criterion. [ABSTRACT FROM AUTHOR]

Distributions of mechanical and thermal stresses in a plunger of the high pressure die casting machine with a horizontal shot sleeve have been considered for a flat thermal stationary problem. An axial pressure of the plunger pressing in the technological process has been accounted for as well. Principal and equivalent stresses have been determined within two different hypotheses on the strength of materials, including one theory covering various allowable stresses in tension and compression. Four plunger material variants have been analysed. [ABSTRACT FROM AUTHOR]

The study discusses the thermo-mechanical stress distribution in the plunger of a cold chamber casting machine with a horizontal casting chamber in the stationary aspect. The main stresses as well as the reduced stresses were determined for four different strength hypotheses, two of which took into account different acceptable maximal tensile and compressive stresses. For comparative purposes, the calculations were performed for three different construction materials used for cold chamber pressure machine plungers: grey pearlitic cast iron, high silicon bronze and beryllium bronze, as well as one more type of bronze, which has not been used for plungers so far, i.e. aluminium-iron-nickel bronze, constituting the initial alloy for the newly-developed complex bronzes with high wear resistance and elevated strength. [ABSTRACT FROM AUTHOR]

The established method for determining dike heights and dimensioning river training structures is to assess the resulting backwater by numerical modelling. The common consensus is that bottom friction determines the backwater and that momentum advection only has a local effect. We demonstrate that the numerical/artificial backwater contribution from the momentum advection approximation can be of the same order of magnitude as the bottom friction contribution, depending on the advection scheme. This is realized using a one-dimensional analysis and verified using a set of one- and two-dimensional test problems including a wavy bed case, flow over emerged and submerged groynes and finally an actual river. We compare first- and second-order accurate advection schemes and compute their artificial contribution to the backwater, for a range of practically- feasible grid resolutions. The tests demonstrate that the conservation/constancy properties of the scheme determine the size of this contribution, rather than the order of the scheme. [ABSTRACT FROM AUTHOR]

Copyright of Fibres & Textiles in Eastern Europe is the property of Sciendo and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Bending and membrane components of transverse forces in a fixed square isotropic plate under simultaneous compression and transverse loading were established within the first-order shear deformation theory (FSDT), the simple first-order shear deformation theory (S-FSDT), and the classical plate theory (CPT). Special attention was drawn to the fact that bending components were accompanied by transverse deformations, whereas membrane components were not, i.e., the plate was transversely perfectly rigid. In the FSDT and the S-FSDT, double assumptions concerning transverse deformations in the plate hold. A new formulation of the differential equation of equilibrium with respect to the transverse direction of the plate, using a variational approach, was proposed. For nonlinear problems in the mechanics of thin-walled plates, a range where membrane components should be considered in total transverse forces was determined. It is of particular significance as far as modern composite structures are concerned. [ABSTRACT FROM AUTHOR]

For an isotropic square plate subject to unidirectional compression in the postbuckling state, components of transverse forces in bending, membrane transverse components and total components of transverse forces were determined within the first-order shear deformation theory (FSDT), the simple first-order shear deformation theory (S-FSDT), the classical plate theory (CPT) and the finite element method (FEM). Special attention was drawn to membrane components of transverse forces, which are expressed with the same formulas for the first three theories and do not depend on membrane deformations. These components are nonlinearly dependent on the plate deflection. The magnitudes of components of transverse forces for the four theories under consideration were compared. [ABSTRACT FROM AUTHOR]

The present paper deals with the interactive buckling of thin-walled lipped channel (LC) beams under the bending moment in the web plane when the shear lag phenomenon and distortional deformations are taken into account. A plate model (2D) was adopted for LC beams. The structures were assumed to be simply supported at the ends. A modal method of solution to the interactive buckling problem within Koiter's asymptotic theory, using the semi-analytical method (SAM) and the transition matrix method, was applied. LC-beams, from short through medium-long via long to very long beams, were considered. The paper focuses on the influence of the secondary global buckling mode on the load carrying capacity for the steel LC-beams under bending. [ABSTRACT FROM AUTHOR]