Search

Diffraction limits the minimum resolvable feature on remotely observed targets to $\lambda R_{c}/A_{c}$, where $\lambda$ is the operating wavelength, $R_{c}$ is the range to the target and $A_{c}$ is the diameter of the observing aperture. Resolution is often further reduced by scatter or turbulence. Here we show that analysis of scattered coherent illumination can be used to achieve resolution proportional to $\lambda R_{s}/A_{s}$, where $R_{s}$ is the range between the scatterer and the target and $A_{s}$ is the diameter of the observed scatter. Theoretical analysis suggests that this approach can yield resolution up to 1000× better than the diffraction limit. We present laboratory results demonstrating $>30\times$ improvement over direct observation. In field experiments, we use a 23.5 cm aperture telescope at 100 m to resolve 27.78 $\mu$m features, improving on diffraction limited resolution by $>10\times$. The combination of lab and field results demonstrates the potential of scatter analysis to achieve multiple order of magnitude improvements in resolution in applications spanning microscopy and remote sensing.

In a lidar system, replacing moving components with solid-state devices is highly anticipated to make a reliable and compact lidar system, provided that a substantially large beam area with a large angular extent as well as high angular resolution is assured for the lidar transmitter and receiver. A new quasi-solid-state lidar optical architecture employs a transmitter with a two-dimensional MEMS mirror for fine beam steering at a fraction of the degree of the angular resolution and is combined with a digital micromirror device for wide FOV scanning over 37 degree while sustaining a large aperture area of 140 mm squared. In the receiver, a second digital micromirror device is synchronized to the transmitter DMD, which enables a large FOV receiver. An angular resolution of 0.57°(H) by 0.23° (V) was achieved with 0.588 fps for scanning 1344 points within the field of view.

Real-time, simultaneous, and adaptive beam steering into multiple regions of interest replaces conventional raster scanning with a less time-consuming and flexible beam steering framework, where only regions of interest are scanned by a laser beam. CUDA-OpenGL interoperability with a computationally time-efficient computer-generated hologram (CGH) calculation algorithm enables such beam steering by employing a MEMS-based phase light modulator (PLM) and a Texas Instruments Phase Light Modulator (TI-PLM). The real-time CGH generation and display algorithm is incorporated into the beam steering system with variable power and scan resolution, which are adaptively controlled by camera-based object recognition. With a mid-range laptop GPU and the current version of the MEMS-PLM, the demonstrated scanning speed can exceed 1000 points/s (number of beams > 5) and potentially exceeds 4000 points/s with state-of-the-art GPUs.

Phase light modulator (PLM) by MEMS mirror array operating in a piston-mode motion enables a high-speed diffractive beam steering in a random-access and flexible manner that makes a lidar system more intelligent and adaptive. Diffraction efficiency is determined by the range of the piston motion of the MEMS array; consequently, a larger range of the piston motion is required for beam steering in infrared, such as for lidar. We demonstrated how the range of the piston motion is optically enhanced by a factor of two with a light-recycling optics based on Talbot self-imaging. The proposed optical architecture extends the usable range of the wavelength so that a MEMS-PLM designed for visible wavelength is applicable for a high-efficiency beam steering at an infrared wavelength of 1550 nm with an improved diffraction efficiency of 30%.

The recent development of the Micro Electromechanical System (MEMS) Phase Light Modulator (PLM) enables fast laser beam steering for lidar applications by displaying a Computer-Generated Hologram (CGH) without employing an iterative CGH calculation algorithm. We discuss the application of MEMS PLM (Texas Instruments PLM) for quasi-continuous laser beam steering by deterministically calculated CGHs. The effect on the diffraction efficiency of PLM non-equally spaced phase levels was quantified. We also address the CGH calculation algorithm and an experimental demonstration that steered and scanned the beam into multiple regions of interest points, enabling beam steering for lidar without sequential raster scanning.

The metrology of membrane structures, especially inflatable, curved, optical surfaces, remains challenging. Internal pressure, mechanical membrane properties, and circumferential boundary conditions imbue highly dynamic slopes to the final optic surface. Here, we present our method and experimental results for measuring a 1 m inflatable reflector’s shape response to dynamic perturbations in a thermal vacuum chamber. Our method uses phase-measuring deflectometry to track shape change in response to pressure change, thermal gradient, and controlled puncture. We use an initial measurement as a virtual null reference, allowing us to compare 500 mm of measurable aperture of the concave f/2, 1-meter diameter inflatable optic. We built a custom deflectometer that attaches to the TVAC window to make full use of its clear aperture, with kinematic references behind the test article for calibration. Our method produces 500 × 500 pixel resolution 3D surface maps with a repeatability of 150 nm RMS within a cryogenic vacuum environment (T = 140 K, P = 0.11 Pa).

A new method, wavelength diversity detection (WDD), for improving signal quality is proposed and its effectiveness is numerically confirmed. We consider that WDD is especially effective for high-capacity systems having low hologram diffraction efficiencies. In such systems, the signal quality is primarily limited by coherent scattering noise; thus, effective improvement of the signal quality under a scattering-limited system is of great interest. WDD utilizes a new degree of freedom, the spectrum width, and scattering by molecules to improve the signal quality of the system. We found that WDD improves the quality by counterbalancing the degradation of the quality due to Bragg mismatch. With WDD, a higher-scattering-coefficient medium can improve the quality. The result provides an interesting insight into the requirements for material characteristics, especially for a large-M/# material. In general, a larger-M/# material contains more molecules; thus, the system is subject to more scattering, which actually improves the quality with WDD. We propose a pathway for a future holographic data storage system (HDSS) using WDD, which can record a larger amount of data than a conventional HDSS. [ABSTRACT FROM AUTHOR]

A practical optical system design that takes into account environmental factors is highly desirable. However, it is in general a time-consuming process, which requires a massive iterations of simulations. This is also one of the bottlenecks of the optical design of angular multiplexed holographic data storage systems. To develop a practical method to evaluate the effect of vibrations, a three-dimensional vibration model is developed. The model describes the vibration effect on normalized intensity on the basis of a single statistical figure of merit. Such a single figure of merits is adopted for designing a robust and efficient write strategy, which is applicable to a wide range of vibration waveforms to increase write data transfer rate. Also, optimum optical system parameters are identified. We propose a numerical aperture of 0.572 and a pixel pitch of 6.9 µm which can improve capacity and data transfer rate without sacrificing the vibration margin. [ABSTRACT FROM AUTHOR]

Mechanical instabilities during recording and involved degradation of signal quality in high density and high data transfer rate holographic data storage system (HDSS) is one of the obstacles to prevent the technology from being a stable system. We analytically formulated effects of mechanical instabilities of a Galvano mirror and spindle motor on the HDSS by incorporating the concept of a time-averaged holography. Mechanical parameters such as amplitude and frequency of mechanical oscillation are related to optical parameters such as amplitude and phase of reference and signal beams. Especially, the analytical formulation led to a new method of optical and post compensation for mechanical instability during recording hologram. The optical post compensation method enables a robust implementation of HDSS against mechanical instabilities. [ABSTRACT FROM AUTHOR]

It is crucial to understand the effects of random mechanical vibration on holographic data storage system, but such effects have not yet been formalized. Therefore, we developed a generalized formalization of vibration effects using a concept of time-averaged holography. Normalized intensity as a function of a statistical measure of vibration waveforms is simulated by simple harmonic oscillation, then normalized intensity is predicted well even for random vibration waveforms. Servo and mechanical systems will be designed solely by specifying the required signal level, which enables efficient product development. [ABSTRACT FROM AUTHOR]