Search

Bark on trees protects the plant against environmentally adverse conditions as well as fungi and insect attacks. There are different chemical substances, mostly in the outer bark of trees, which can stop fungi from developing. Bark as a by-product of wood plantations is available in high quantity and can serve as an excellent source for the production of eco-fungicides. In the presented article, bark of various poplar clones from two short-rotation coppices (SRC) in Poland and Germany was examined to determine the chemical composition, the possible extraction of potential fungicides (terpenes, aromatic and phenolic substances), and influence of their extracts on slowing the growth of mold fungi. It was proved that the content of the fungicidal substances depends strongly on the clone type. Two methods of extraction—Soxhlet and batch—were compared to obtain fungicidal extracts. Fungicidal substances were found in extracts gained with both approaches. Triterpenes, fatty acids, aldehydes, and alcohols were primarily the active fungicides in the Soxhlet extracts, whereas phenolic substances act as fungicides in the batch extracts.

The aim of this work is to establish a bending test method as evaluation criteria for mechanical properties (strength and modulus of elasticity) of veneers. The bending test is one essential and ea...

In this study, the relatively new picture frame method applied to wood is compared with three established shear test methods, namely the experimental modal analysis, the square plate twist method and the torsion test. For the investigations, the wood species European beech (Fagus sylvatica L.) and spruce (Picea abies L. Karst.) were used and the shear tests were conducted in LR and RL direction. The results show comparable shear moduli for beech and spruce in the range of 931–1289 Nmm−2 and 495–842 Nmm−2, respectively. In contrast to the theory of linear elastic orthotropic materials, significant differences in the results of the picture frame method between LR and RL direction were observed for spruce.

In the field of lightweight construction, the use of natural fibers as reinforcement in composites has been increasingly discussed. Additionally, the damping properties of natural fibers are known from fiber materials such as fiber insulation boards. In the scope of the work presented here, the focus is on identifying the potential of natural fibers for lightweight structures with high vibration damping capacity. For this purpose, test specimens made of flax fiber-reinforced and glass fiber-reinforced thermoplastic composites were manufactured and characterized. Contrary to expectations, the flax fiber-reinforced composite exhibited an almost isotropic damping characteristic. A comparison of the damping and stiffness properties determined by measurement confirms the high potential of natural fiber-reinforced materials for lightweight structures with high damping.

A new method for the determination of shear modulus and shear strength is presented in this study using a shear or picture frame. A shear frame in accordance with DIN SPEC 4885 is in other fields, such as fibre reinforced composites, state of the art. Here, a square test specimen with recessed corners is held in the shear frame and subjected to a quite uniform shear deformation state. To determine the shear modulus and the shear strength, tensile load acting on the shear frame and the associated shear strain are measured. This method has the advantage of simultaneous determination of the shear modulus and the shear strength. Thin square wooden plates of European beech (Fagus sylvatica L.) were tested in all anatomical directions. The results show good accordance with literature values. The highest values of shear modulus and shear strength were yielded for the LR plane, followed by the values in the LT plane. The tests in the RT plane clearly resulted in the lowest values.

Untreated and thermally modified woods of cherry, service tree, pear and plum were investigated as potential substitutions for Indian rosewood in guitar making. Acoustic properties such as dynamic modulus of elasticity, dynamic shear modulus in LR-plane and loss coefficient as an indicator for damping were determined by means of experimental modal analysis and the mechanical properties by means of static bending and hardness test. The swelling behavior was also investigated. The results suggest that cherry and service tree could be used as alternative back and side material and plum and service tree may also be used for fingerboards. Thermal modifications at 160 °C for 8 h improve swelling behavior, mechanical properties, but damping was slightly increased for cherry and pear. No significant change of Brinell hardness was observed owing to thermal modification.

This research investigated the effect of different fractions of commercial wood flour (Type c100 from JRS, Germany) on mechanical and physical properties of wood-polymer composites (WPC). The fractions were named regarding the mean lengths of their particles in µm; 80, 130, 255, 405 and 485. The composite samples were manufactured with 30 wt% of wood flour fractions of all five groups as well as the not fractionated flour, and 70 wt% of cellulose propionate (CP). The melt mass-flow rate (MFR) of the different granules, tensile strength, and modulus of elasticity, flexural strength, flexural modulus and the impact strength of the injection molded specimens as well as the water uptake were determined in this study. WPCs with the specific size range used in this investigation exhibited improved strength and modulus of elasticity in tensile and flexural tests, compared to pure CP. Using fraction 255, the mechanical properties increased the most. Tensile strength rose by 28 and 13% compared to CP and to WPC with the not fractioned wood powder, respectively. Fraction 255 increased flexural strength by 33 and 5% compared to CP and WPC with the not fractioned flour. The MFR (tested at 190 °C with 7.16 kg) of WPC_255 is the lowest with 2.3 g/10 min. Composites with the smallest particles showed the least water uptake.

During the manufacture of veneers cracks and other damages occur. These damages impair and reduce the veneer cross-section. By means of microscopic investigations cracks and damages in veneer cross-sections were documented and measured. These investigations were conducted with industrially sliced 0.3, 0.6 and 1.2 mm thick veneers. The results determine the residual cross-sections in dependence of veneer thickness which can be used for numerical calculations.

Large string instruments, such as cellos and double basses, are manufactured, bought and played all over the world. Thereby they are exposed to different climate conditions. This paper describes shape alterations using the example of a double bass stored at different climatic conditions. By means of an optical measurement these shape alterations were recorded and represented. The results clearly show spots with strong and without deformations. Thus, weak points of the construction are localised and improvements can be established for the construction of string instruments.

Milling is one of the most important cutting procedures in the wood industry. It allows shaping of workpiece surfaces with a high chip-removal rate. This is possible because of a fast rotary cutting motion, the possibility to place many cutting edges on the tool circumference and a fast linear feeding motion. Due to these different kinds of motions the resulting effective motion follows a prolonged cycloid which forms periodic waves on the workpiece surface. These surface patterns, called cuttermarks, may be visible on the machined surface after cutting and mainly influence the workpiece quality. Further surface machining steps are required to meet the demanded standards of surface quality. This is why researchers have been looking for possibilities to lower or avoid these cuttermarks. Beside the description and the analyses of the geometry of cuttermarks, magnitudes of disturbance, mechanical and mechatronic approaches and alternative procedures will be introduced and discussed. Especially mechat...

The possibility of the use of thermally modified European beech (Fagus sylvatica L.) in necks of electric bass guitars for the substitution of Hard maple (Acer saccharum) has been studied. The heat treatments were performed at relatively mild treatment temperatures of 140 and 160 °C for 12 h. The acoustic properties were determined by means of experimental modal analysis (EMA) and the mechanical properties by means of static and impact bending tests. The results show that both the acoustic and mechanical, static properties of beech improve significantly owing to thermal modification, being similar or better compared to Hard maple. The impact bending strengths decrease owing to thermal modification. Additional tests on complete necks of electric bass guitars by means of EMA and plucking tests on total instruments show that thermally treated beech at mild temperatures can substitute Hard maple for the use as neck material in electric bass guitars.

This paper deals with the determination of the capillary pore-size distribution (CPSD) and equilibrium moisture content (EMC) of untreated and thermally modified (TM) Norway spruce [Picea abies (L.) Karst.] by means of the pressure plate technique (PPT). Desorption experiments were conducted at very high values of relative humidity (RH) in the range between 99.2% and 100%. The thermal modification of spruce results in an alteration of the CPSD, owing to the formation of intercellular cracks in the middle lamella, as a result of cell-wall compression. The desorption curves for both untreated and TM spruce show an extremely upward bend at 99.97% RH. This step reflects an EMC of 38.1% for untreated spruce and 33.8% for TM spruce. None of the samples shrunk during the PPT measurements. Following desorption experiments at 97.4% RH, all samples shrunk. This step reflects an EMC of 27.9% for untreated spruce and 21.7% for TM spruce.

One of the visual modification of wood is the formation of dark zone lines (ZLs) via interaction of fungi. The result is called spalted wood, which has hitherto been produced mainly in small batches. The main goal of the present study is to further develop techniques for rapid formation of ZLs in hardwoods. Various white rot and brown rot fungi were tested to this purpose. Initially, interactions of 148 combinations of 17 basidiomycetes in malt extract agar were evaluated and their antagonistic interactions were characterised in order to identify fungal pairs capable of rapidly forming high-quality ZLs. Six types of interactions were observed, among others; antibiosis and inhibition in contact, which differ in terms of variables including mycelial overgrowth and zone line formation. Furthermore, 23 pairs of ZL forming fungi on malt extract agar were identified. Then the interactions of five selected pairs of fungi grown on the hardwood species Acer pseudoplatanus L., Betula pendula Roth. and Populus nigra L. were examined to assess their utility for controlled mycological wood modification, also in terms of a possible substrate dependency of their interactions. The results indicate that Lentinus tigrinus fungus is one of the best and quickest producer of ZLs in mycological wood modification.

International audience; The aim of this work was to analyse the material behaviour of thermally modified and native spruce by load applied perpendicularly to the grain. Therefore, thermally modified and native samples were prepared for bending tests with the load in tangential direction. The bending strength in radial direction decreases significantly with the thermal treatment. The fracture surfaces in the tangential section of the bending samples after testing were analysed with a scanning electron microscope. For native samples, the typical failure was found in the intercellular area. For thermally modified samples, failure of the entire cell wall was observed. The material behaviour is more brittle, as demonstrated by the load-deflection curves, but also by anatomical studies of the fracture surfaces.