Search

International audience; The Giant Segmented Mirror Telescopes (GSMTs) including the Giant Magellan Telescope (GMT), the Thirty Meter Telescope (TMT), and the European Extremely Large Telescope (E-ELT), all have extreme adaptive optics (ExAO) instruments planned that will use pyramid wavefront sensors (PWFS). The ExAO instruments all have common features: a high-actuator-count deformable mirror running at extreme speeds (>1 kHz); a high-performance wavefront sensor (WFS); and a high-contrast coronagraph. ExAO WFS performance is currently limited by the need for high spatial sampling of the wavefront which requires large detectors. For ExAO instruments for the next generation of telescopes, alternative architectures of WFS are under consideration because there is a trade-off between detector size, speed, and noise that reduces the performance of GSMT-ExAO wavefront control. One option under consideration for a GSMT-ExAO wavefront sensor is a three-sided PWFS (3PWFS). The 3PWFS creates three copies of the telescope pupil for wavefront sensing, compared to the conventional four-sided PWFS (4PWFS), which uses four pupils. The 3PWFS uses fewer detector pixels than the 4PWFS and should therefore be less sensitive to read noise. Here we develop a mathematical formalism based on the diffraction theory description of the Foucault knife-edge test that predicts the intensity pattern after the PWFS. Our formalism allows us to calculate the intensity in the pupil images formed by the PWFS in the presence of phase errors corresponding to arbitrary Fourier modes. We use these results to motivate how we process signals from a 3PWFS. We compare the raw intensity (RI) method, and derive the Slopes Maps (SM) calculation for the 3PWFS, which combines the three pupil images of the 3PWFS to obtain the X and Y slopes of the wavefront. We then use the Object Oriented MATLAB Adaptive Optics toolbox (OOMAO) to simulate an end-to-end model of an AO system using a PWFS with modulation and compare the performance of the 3PWFS to the 4PWFS. In the case of a low read noise detector, the Strehl ratios of the 3PWFS and 4PWFS are within 0.01. When we included higher read noise in the simulation, we found a Strehl ratio gain of 0.036 for the 3PWFS using RI over the 4PWFS using SM at a stellar magnitude of 10. At the same magnitude, the 4PWFS RI also outperformed the 4PWFS SM, but the gain was only 0.012 Strehl. This is significant because 4PWFS using SM is how the PWFS is conventionally used for AO wavefront sensing. We have found that the 3PWFS is a viable WFS that can fully reconstruct a wavefront and produce a stable closed-loop with correction comparable to that of a 4PWFS, with modestly better performance for high read-noise detectors.

Snellen, I.A.G. et al., In this White Paper, which was submitted in response to the European Space Agency (ESA) Voyage 2050 Call, we recommend the ESA plays a proactive role in developing a global collaborative effort to construct a large high-contrast imaging space telescope, e.g. as currently under study by NASA. Such a mission will be needed to characterize a sizable sample of temperate Earth-like planets in the habitable zones of nearby Sun-like stars and to search for extraterrestrial biological activity. We provide an overview of relevant European expertise, and advocate ESA to start a technology development program towards detecting life outside the Solar System., I.S. acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation program under grant agreement No 694513. A.L.M. acknowledges the financial support of the F.R.S.-FNRS through a postdoctoral researcher grant. MB acknowledges support from the UK Science and Technology Facilities Council (STFC) research grant ST/S000631/1. I.R. acknowledges support from the Spanish Ministry of Science and Innovation and the European Regional Development Fund through grant PGC2018-098153-B-C33, as well as the support of the Generalitat de Catalunya/CERCA programme. E.P. acknowledges support from the Spanish Ministry of Science through grant PGC2018-098153-B-C31. J.M.D. acknowledges funding from the European Research Council (ERC) under the European Unions Horizon 2020 research and innovation programme (grant agreement no. 679633; Exo-Atmos) Part of this research was carried out at the Jet Propulsion Laboratory, California Institute of Technology, under a contract with the National Aeronautics and Space Administration. We acknowledge financial support from the ASI-INAF agreement n.2018-16-HH.0 We acknowledge financial support from Spanish MCIU SEV-2017-0709 and PID2019-110689RB-I00 awards. We acknowledge financial support from the ASI-INAF agreement n.2018-16-HH.0 AV acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 757561). KH acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 771620). NJM acknowledges funding from the Leverhulme Trust, and a Science and Technology Facilities Council Consolidated Grant (ST/R000395/1). PdV acknowledges funding from the Netherlands Organisation for Scientific Research NWO (Veni Grant No. 639.041.750). IP acknowledges financial support from the ASI-INAF agreements 2019-29-HH.06-HH.0 and 2015-019-R.1-2018. FS acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement no. 678194; FALCONER). MJ acknowledges support from the Knut and Alice Wallenberg foundation (KAW). JLB acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation program under grant agreement No 805445. T.H. acknowledges support from the European Research Council under the Horizon 2020 Framework Program via the ERC Advanced Grant Origins 83 24 28. JLG acknowledges ISSI Team 464 for useful discussion.

Current and future high-contrast imaging instruments require extreme adaptive optics systems to reach contrasts necessary to directly imaged exoplanets. Telescope vibrations and the temporal error induced by the latency of the control loop limit the performance of these systems. One way to reduce these effects is to use predictive control. We describe how model-free reinforcement learning can be used to optimize a recurrent neural network controller for closed-loop predictive control. First, we verify our proposed approach for tip–tilt control in simulations and a lab setup. The results show that this algorithm can effectively learn to mitigate vibrations and reduce the residuals for power-law input turbulence as compared to an optimal gain integrator. We also show that the controller can learn to minimize random vibrations without requiring online updating of the control law. Next, we show in simulations that our algorithm can also be applied to the control of a high-order deformable mirror. We demonstrate that our controller can provide two orders of magnitude improvement in contrast at small separations under stationary turbulence. Furthermore, we show more than an order of magnitude improvement in contrast for different wind velocities and directions without requiring online updating of the control law.

In situexperimental studies have been key in uncovering the often elusive pathways of nucleation and crystal growth. In the field of material science and medicine this offers the prospect of controlling crystallization processes to fight disease or tailor materials towards specific applications. To further advance this quest there is a need for flexible techniques mapping the different stages of crystallization with maximal sensitivity. This article reviews the benefits of nonlinear optical techniques to take on this challenge. We provide a perspective on various nucleation and crystal growth studies that were carried out by nonlinear optical probing techniques. A theoretical background is established, different relevant nonlinear optical phenomena are defined, and optical setups that have been used by various authors are summarized. A primary focus is demonstrating the benefits of nonlinear optical techniques for thein situstudy of crystallization. These benefits include low detection limits, complementary information by combining second- and third-order techniques, as well as relatively simple bench-top setups. Through microscopy, high contrast imaging of concomitant formations can moreover be achieved. The discussion outlines several studies involving ionic compounds, noble metal nanoparticles, polymers, metal organic frameworks and pharmaceutical compounds. Finally, we discuss future evolutions in nonlinear optical probing that are expected to further advance the field.

International audience; The Center for Optics and Photonics of the National Astronomical Research Institute of Thailand, together with the Institut d'Optique Graduate School and the Centre de Recherche Astrohpysique de Lyon (CRAL), is currently developing the Evanescent Wave Coronagraph (EvWaCo). The coronagraph relies on the tunneling effect to produce a fully achromatic focal plane mask (FPM) with an adjustable size. The full instrument comprises a coronagraph and adaptive optics system that will be mounted on the Thai National Telescope and is specified to reach a raw contrast of 10−4 at an inner working angle of 3 Airy radii. The coronagraph will be used to perform high contrast observations of stellar systems during on-sky observations over the spectral domain [600 nm, 900 nm]. In this paper, we present the opto-mechanical design of the EvWaCo prototype and the performance measured in laboratory conditions. We also discuss the potential applications for space-based observations and the development plan under this project in the next five years.

NASA is developing starshade technology to Technology Readiness Level 5 within a directed activity called S5. The objective of S5 is to mature starshade technology to the level that exoplanet imaging missions, such as Starshade Rendezvous and HabEx, can begin the formulation phase. This paper outlines the S5 activity as a whole, to show how it closes all starshade technology gaps in a mutually consistent way. It serves as a companion paper to several other papers in this special section that report progress in specific starshade technologies.

Starshade concepts must be stowed within rocket fairings for launch and then deployed in space. The in-plane deployment accuracy must be on the order of hundreds of micrometers for sufficient starlight suppression to enable the detection and study of Earth-like exoplanets around nearby Sun-like stars. We describe tests conducted to demonstrate deployment repeatability of two key structural subsystems of the “furled” starshade architecture—the petal and the inner disk. Together, the petals and the inner disk create the in-plane shape of a starshade. Test articles to represent the petal and inner disk subsystems were constructed at relevant scales for a 26-m-diameter starshade. These test articles were subjected to stowage-and-deployment cycles and their shapes were measured. The measured performance—tens of parts per million of petal strain after deployment, and hundreds of micrometers of inner disk deployment accuracy—was found to be within required allocations.

Large surveys with new-generation high-contrast imaging instruments are needed to derive the frequency and properties of exoplanet populations with separations from ~5 to 300 au. A careful assessment of the stellar properties is crucial for a proper understanding of when, where, and how frequently planets form, and how they evolve. The sensitivity of detection limits to stellar age makes this a key parameter for direct imaging surveys. Aims. We describe the SpHere INfrared survey for Exoplanets (SHINE), the largest direct imaging planet-search campaign initiated at the VLT in 2015 in the context of the SPHERE Guaranteed Time Observations of the SPHERE consortium. In this first paper we present the selection and the properties of the complete sample of stars surveyed with SHINE, focusing on the targets observed during the first phase of the survey (from February 2015 to February 2017). This early sample composed of 150 stars is used to perform a preliminary statistical analysis of the SHINE data, deferred to two companion papers presenting the survey performance, main discoveries, and the preliminary statistical constraints set by SHINE. Methods. Based on a large database collecting the stellar properties of all young nearby stars in the solar vicinity (including kinematics, membership to moving groups, isochrones, lithium abundance, rotation, and activity), we selected the original sample of 800 stars that were ranked in order of priority according to their sensitivity for planet detection in direct imaging with SPHERE. The properties of the stars that are part of the early statistical sample wererevisited, including for instance measurements from the Gaia Data Release 2. Rotation periods were derived for the vast majority of the late-type objects exploiting TESS light curves and dedicated photometric observations. Results. The properties of individual targets and of the sample as a whole are presented. © ESO 2021. SPHERE is an instrument designed and built by a consortium consisting of IPAG (Grenoble, France), MPIA (Heidelberg, Germany), LAM (Marseille, France), LESIA (Paris, France), Laboratoire Lagrange (Nice, France), INAF – Osservatorio di Padova (Italy), Observatoire de Genève (Switzerland), ETH Zürich (Switzerland), NOVA (Netherlands), ONERA (France) and ASTRON (Netherlands) in collaboration with ESO. SPHERE was funded by ESO, with additional contributions from CNRS (France), MPIA (Germany), INAF (Italy), FINES (Switzerland) and NOVA (Netherlands). SPHERE also received funding from the European Commission Sixth and Seventh Framework Programmes as part of the Optical Infrared Coordination Network for Astronomy (OPTICON) under grant number RII3-Ct-2004-001566 for FP6 (2004–2008), grant number 226 604 for FP7 (2009–2012) and grant number 312430 for FP7 (2013–2016). This research has made use of the SIMBAD database and Vizier services, operated at CDS, Strasbourg, France and of the Washington Double Star Catalog maintained at the US Naval Observatory. This work has made use of data from the European Space Agency (ESA) mission Gaia (https://www.cosmos.esa.int/gaia), processed by the Gaia Data Processing and Analysis Consortium (DPAC, https://www.cosmos.esa.int/web/gaia/dpac/consortium). Funding for the DPAC has been provided by national institutions, in particular the institutions participating in the Gaia Multilateral Agreement. This paper includes data collected with the TESS mission, obtained from the MAST data archive at the Space Telescope Science Institute (STScI). Funding for the TESS mission is provided by the NASA Explorer Program. STScI is operated by the Association of Universities for Research in Astronomy, Inc., under NASA contract NAS 5–26555. This paper has made use of data products available in ESO archive. Program ID: 60.A-9036(A); 072.C-0488(E) (PI Mayor), 074.C-0364(A) (PI Robichon), 074.C-0037(A) (PI Gunther), 075.C-0202(A) (PI Gunther), 075.C-0689(A) (PI Galland), 076.C-0010(A) (PI Gunther), 077.C-0012(A) (PI Gunther), 077.C-0295(D) (PI Galland), 078.D-0245(C) (PI Dall), 079.C-0046(A) (PI Gunther), 080.D-0151(A) (PI Hatzes), 080.C-0712(A) (PI Desort), 180.C-0886(A) (PI Bonfils), 082.C-0718(B) (PI Bonfils), 082.C-0427(A) (PI Doellinger), 082.C-0390(A) (PI Weise), 183.C-0437(A) (PI Bonfils), 083.C-0794(A) (PI Chauvin), 084.C-1039(A) (PI Chauvin), 184.C-0815(B) (PI Desort), 089.C-0732(A) (PI Lo Curto), 191.C-0873(D) (PI Bonfils), 192.C-0224(A) (PI Lagrange), 097.C-0864(B) (PI Lannier), 098.C-0739(A) (PI Lagrange), 099.C-0205(A) (PI Lagrange), 099.C-0458(A) (PI Lo Curto), 1101.C-0557(A) (PI Lagrange). We have used data from the WASP public archive in this research. The WASP consortium comprises of the University of Cambridge, Keele University, University of Leicester, The Open University, The Queen’s University Belfast, St. Andrews University and the Isaac Newton Group. Funding for WASP comes from the consortium universities and from the UK’s Science and Technology Facilities Council. Based on data retrieved from the SOPHIE archive at Observatoire de Haute-Provence (OHP), available at http://atlas.obs-hp.fr/sophie/. We thank the anonymous referee for useful comments. S.D., V.D., D.M. and R.G. acknowledge the support by INAF/Frontiera through the “Progetti Premiali” funding scheme of the Italian Ministry of Education, University, and Research, the PRIN-INAF 2019 “Planetary systems at young ages” (PLATEA) and the ASI-INAF agreement n.2018-16-HH.0. AV acknowledges funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 757561). A.M.L. acknowledges funding from Agence Nationale de la Recherche (France) under contract number ANR-14-CE33-0018. J.C. was supported by SC Space Grant and Fulbright Colombia. M.B. acknowledges funding by the UK Science and Technology Facilities Council (STFC) grant no. ST/M001229.

METIS is one of the first three instruments for the ELT, Europe’s next-generation ground-based telescope. It will offer imaging, coronagraphy and spectroscopy in the L, M and N bands for general-purpose science in astrophysics. Among its main science drivers are circumstellar disks and extrasolar planets observations, which requires demanding high contrast imaging techniques. In that framework, METIS will be equipped with state-of-the-art phase mask coronagraphs: Apodizing Phase Plate (APP) and Annular Grooves Phase Mask (AGPM). Manufacturing the AGPM coronagraphs is a complex process that requires performance assessment with specific testing before implementation into the instrument. At Department of Astrophysics (CEA Saclay, France), responsible for the testing of the N-band AGPMs, a previously available test bench with a telescope simulator and cryogenic facility has been upgraded to comply with the AGPM tests requirements. This paper presents these requirements and describes the test bench design adopted. Then, based on preliminary results, we discuss the original solutions that permitted to reach our goals.

Focal plane wavefront sensing is an elegant solution for wavefront sensing since near-focal images of any source taken by a detector show distortions in the presence of aberrations. Non-Common Path Aberrations and the Low Wind Effect both have the ability to limit the achievable contrast of the finest coronagraphs coupled with the best extreme adaptive optics systems. To correct for these aberrations, the Subaru Coronagraphic Extreme Adaptive Optics instrument hosts many focal plane wavefront sensors using detectors as close to the science detector as possible. We present seven of them and compare their implementation and efficiency on SCExAO. This work will be critical for wavefront sensing on next generation of extremely large telescopes that might present similar limitations., Comment: SPIE proceeding : Astronomical Telescopes + Instrumentation 2020. arXiv admin note: text overlap with arXiv:1912.10179

The SPEED project aims at developing and testing key recipes for high-contrast imaging at small angular separations with unfriendly telescope apertures. SPEED combines optimized segmented aperture coronagraphy, dual-deformable mirrors wavefront control and shaping architecture for creating a dark hole in the scientific image by deformable mirror (DM) actuation. The challenge is to overcome the various fundamental limitations for quasi-static speckle calibration at very small angular separations. We report on the progress made in elaborating an accurate simulated model of our instrument in preparation for the wavefront control and wavefront shaping strategy with a multi-DM setup.

Massive stars like company. However, low-mass companions have remained extremely difficult to detect at angular separations ($\rho$) smaller than 1" (~1000-3000 au considering typical distance to nearby massive stars) given the large brightness contrast between the companion and the central star. Constraints on the low-mass end of the companions mass-function for massive stars are however needed, for example to help distinguishing between various scenarios for the formation of massive stars. To obtain statistically significant constraint on the presence of low-mass companions beyond the typical detection limit of current surveys ($\Delta \mathrm{mag} \lesssim 5$ at $\rho \lesssim 1$"), we initiated a survey of O and Wolf-Rayet stars in the Carina region using the SPHERE coronagraphic instrument on the VLT. In this first paper, we aim to introduce the survey, to present the methodology and to demonstrate the capability of SPHERE for massive stars using the multiple system QZ~Car. High-contrast imaging techniques, such as angular- and spectral-differential imaging techniques as well as PSF-fitting, were applied to detect and measure the relative flux of companions in each spectral channel of the instrument. We detected 19 sources around the QZ~Car system with detection limits of 9~mag at $\rho > 200$~mas for IFS and as faint as 13~mag at $\rho$ > 1".8 for IRDIS (corresponding to sub-solar masses for potential companions). All but two are reported here for the first time. Based on this proof of concept, we showed that VLT/SPHERE allows us to reach the sub-solar mass regime of the companion mass function. This paves the way for this type of observation with a large sample of massive stars to provide novel constraints on the multiplicity of massive stars in a region of the parameter space that has remained inaccessible so far., Comment: Submitted and accepted by A&A. 17 pages, 10 figures

Context. For high-contrast imaging systems, such as VLT/SPHERE, the performance of the system at small angular separations is contaminated by the wind-driven halo in the science image. This halo is a result of the servo-lag error in the adaptive optics (AO) system due to the finite time between measuring the wavefront phase and applying the phase correction. One approach to mitigating the servo-lag error is predictive control. Aims. We aim to estimate and understand the potential on-sky performance that linear data-driven prediction would provide for VLT/SPHERE under various turbulence conditions. Methods. We used a linear minimum mean square error predictor and applied it to 27 different AO telemetry data sets from VLT/SPHERE taken over many nights under various turbulence conditions. We evaluated the performance of the predictor using residual wavefront phase variance as a performance metric. Results. We show that prediction always results in a reduction in the temporal wavefront phase variance compared to the current VLT/SPHERE AO performance. We find an average improvement factor of 5.1 in phase variance for prediction compared to the VLT/SPHERE residuals. When comparing to an idealised VLT/SPHERE, we find an improvement factor of 2.0. Under our 27 different cases, we find the predictor results in a smaller spread of the residual temporal phase variance. Finally, we show there is no benefit to including spatial information in the predictor in contrast to what might have been expected from the frozen flow hypothesis. A purely temporal predictor is best suited for AO on VLT/SPHERE. Conclusions. Linear prediction leads to a significant reduction in phase variance for VLT/SPHERE under a variety of observing conditions and reduces the servo-lag error. Furthermore, prediction improves the reliability of the AO system performance, making it less sensitive to different conditions.

orbitize! is an open-source, object-oriented software package for fitting the orbits of directly-imaged objects. It packages the Orbits for the Impatient (OFTI) algorithm and a parallel-tempered Markov Chain Monte Carlo (MCMC) algorithm into a consistent and intuitive Python API. orbitize! makes it easy to run standard astrometric orbit fits; in less than 10 lines of code, users can read in data, perform one fit using OFTI and another using MCMC, and make two publication-ready figures. Extensive pedagogical tutorials, intended to be navigable by both orbit-fitting novices and seasoned experts, are available on our documentation page. We have designed the orbitize! API to be flexible and easy to use/modify for unique cases. orbitize! was designed by members of the exoplanet imaging community to be a central repository for algorithms, techniques, and know-how developed by this community. We intend for it to continue to expand and change as the field progresses and new techniques are developed, and call for community involvement in this process. Complete and up-to-date documentation is available at orbitize.info., Comment: 9 pages, 4 figures. Submitted to AAS Journals

Development of a highly photostable, renal clearable, and nontoxic new NIR probe (CyG) for precise quantification of albumin in different biofluids and liver targeted in vivo albumin visualization is demonstrated. CyG’s inherent property to interact selectively with albumin among different biomolecules in intracellular environment with high degree of sensitivity helps CyG in targeted liver imaging. In addition to its long excitation/emission wavelengths (λex = 740 nm, λem = 804 nm), which are much above the biological tissue opaque window (400–700 nm) ensuring better photon penetration, diminished tissue autofluorescence and high contrasts, its molecular mass and size are far below the renal cutoff and hence, CyG qualifies as imaging material for clinical studies. We anticipate that CyG will provide new strategies to overcome the pitfall of present day albumin detection methods as well as accelerate the detection process at relatively lower costs without compromising the accuracy of detection. Moreover, t...

We evaluated training deep neural network (DNN) beamformers for the task of high contrast imaging in the presence of reverberation clutter. Training data was generated using simulated hypoechoic cysts and a pseudo nonlinear method for generating reverberation clutter. Performance was compared to standard delay-and-sum (DAS) beamforming on simulated hypoechoic cysts having a different size. For a hypoechoic cyst in the presence of reverberation clutter, when the intrinsic contrast ratio (CR) was -10 dB and -20 dB, the measured CR for DAS beamforming was -9.2±0.8 dB and -14.3±0.5 dB, respectively, and the measured CR for DNNs was -10.7±1.4 dB and -20.0±1.0 dB, respectively. For a hypoechoic cyst with -20 dB intrinsic CR, the contrast-to-noise ratio (CNR) was 3.4±0.3 dB and 4.3±0.3 dB for DAS and DNN beamforming, respectively. These results show that DNN beamforming was able to extend contrast ratio dynamic range (CRDR) by about 10 dB while also improving CNR.

Protein labeling using fluorogenic probes enables the facile visualization of proteins of interest. Herein, we report new fluorogenic probes consisting of a rationally designed coumarin ligand for the live-cell fluorogenic labeling of the photoactive yellow protein (PYP)-tag. On the basis of the photochemical mechanisms of coumarin and the probe-tag interactions, we introduced a hydroxy group into an environment-sensitive coumarin ligand to modulate its spectroscopic properties and increase the labeling reaction rate. The resulting probe had a higher labeling reaction rate constant and a greater fluorescence OFF-ON ratio than any previously developed PYP-tag labeling probe. The probe enabled the fluorogenic labeling of intracellular proteins within minutes. Furthermore, we used our probe to investigate the localization of sirtuin 3 (SIRT3), a mitochondrial deacetylase. Although the nuclear localization of SIRT3 has been controversial, this transient nuclear localization was clearly captured by the rapid, high-contrast imaging enabled by our probe.

For high contrast imaging systems, the time delay is one of the major limiting factors for the performance of the extreme adaptive optics (AO) sub-system and, in turn, the final contrast. The time delay is due to the finite time needed to measure the incoming disturbance and then apply the correction. By predicting the behavior of the atmospheric disturbance over the time delay we can in principle achieve a better AO performance. Atmospheric turbulence parameters which determine the wavefront phase fluctuations have time-varying behavior. We present a stochastic model for wind speed and model time-variant atmospheric turbulence effects using varying wind speed. We test a low-order, data-driven predictor, the linear minimum mean square error predictor, for a near-infrared AO system under varying conditions. Our results show varying wind can have a significant impact on the performance of wavefront prediction, preventing it from reaching optimal performance. The impact depends on the strength of the wind fluctuations with the greatest loss in expected performance being for high wind speeds., 10 pages, 8 figures; Accepted to JOSA A March 2019

Wavefront sensing and control are important for enabling one of the key advantages of using large apertures, namely higher angular resolutions. Pyramid wavefront sensors are becoming commonplace in new instrument designs owing to their superior sensitivity. However, one remaining roadblock to their widespread use is the fabrication of the pyramidal optic. This complex optic is challenging to fabricate due to the pyramid tip, where four planes need to intersect in a single point. Thus far, only a handful of these have been produced due to the low yields and long lead times. To address this, we present an alternative implementation of the pyramid wavefront sensor that relies on two roof prisms instead. Such prisms are easy and inexpensive to source. We demonstrate the successful operation of the roof prism pyramid wavefront sensor on a 8-m class telescope, at visible and near infrared wavelengths ---for the first time using a SAPHIRA HgCdTe detector without modulation for a laboratory demonstration---, and elucidate how this sensor can be used more widely on wavefront control test benches and instruments., Comment: Accepted for publication in PASP, 7 pages, 9 figures, 1 table

A novel DNA nanotetrad mediated crosslinking catalytic hairpin assembly (CCHA) is reported to generate clumps of cross-linked mesh products for high-contrast and simultaneous imaging of multiple mRNAs in living cells.

In the present work we attempt to demonstrate the potential advantages of inserting an electrically tunable q-plate as phase mask in the design of a vector vortex coronagraph. The possibility of el...

We present Subaru/SCExAO+CHARIS broadband ($JHK$-band) integral field spectroscopy of HD 34700 A. CHARIS data recover HD 34700 A's disk ring and confirm multiple spirals discovered in Monnier et al. (2019). We set limits on substellar companions of $\sim12\ M_{\rm Jup}$ at $0\farcs3$ (in the ring gap) and $\sim5\ M_{\rm Jup}$ at $0\farcs75$ (outside the ring). The data reveal darkening effects on the ring and spiral, although we do not identify the origin of each feature such as shadows or physical features related to the outer spirals. Geometric albedoes converted from the surface brightness suggests a higher scale height and/or prominently abundant sub-micron dust at position angle between $\sim45^\circ$ and $90^\circ$. Spiral fitting resulted in very large pitch angles ($\sim30-50^\circ$) and a stellar flyby of HD 34700 B or infall from a possible envelope is perhaps a reasonable scenario to explain the large pitch angles., 17 pages, 14 figures, accepted for publication in ApJ

The Habitable-Exoplanet Observatory (HabEx) is a candidate flagship mission being studied by NASA and the astrophysics community in preparation of the 2020 Decadal Survey. The first HabEx mission concept that has been studied is a large (~4m) diffraction-limited optical space telescope, providing unprecedented resolution and contrast in the optical, with extensions into the near ulttraviolet and near infrared domains. We report here on our team’s efforts in defining a scientifically compelling HabEx mission that is technologically executable, affordable within NASA’s expected budgetary envelope, and timely for the next decade. We also briefly discuss our plans to explore less ambitious, descoped missions relative to the primary mission architecture discussed here.

The Planetary Systems Imager (PSI) is a modular instrument optimized for direct imaging and characterization of exoplanet and disks with the Thirty Meter Telescope (TMT). PSI will operate across a wide wavelength range (≈0.6 - 5μm) to image exoplanets and circumstellar disks in both reflected light and thermal emission. Thanks to the TMT’s large collecting area, PSI will have the sensitivity to directly image and spectrally characterize large gaseous planets with unprecedented sensitivity. PSI will also be capable of imaging rocky planets in the habitable zones of the nearest M-type stars in reflected light and search for biomarkers in their atmospheres. Imaging habitable planets in reflected light is PSI’s most challenging goal, requiring high contrast imaging (HCI) capabilities well beyond what current instruments achieve. This science goal drives PSI’s wavefront sensing and control requirements and defines the corresponding architecture discussed in this paper. We show that PSI must deliver 1e-5 image contrast ≈15 mas separation at λ ≈ 1μm-1.5μm, and that a conventional extreme-AO architecture relying on a single high speed wavefront sensor (WFS) is not sufficient to meet this requirement. We propose a wavefront control architecture relying on both visible light (λ < 1.1 μm) sensing to optimize sensitivity, and near-IR (λ > 1.1 μm) sensors to address wavefront chromaticity terms and provide high contrast imaging capability. We show that this combination will enable speckle halo suppression at the < 1e-5 raw contrast level in near-IR, allowing detection and spectroscopic characterization of potentially habitable exoplanets orbiting nearby M-type stars., Adaptive Optics Systems VI, June 10-15, 2018, Austin, USA, Series: Proceedings of SPIE; no. 10703

The Magellan extreme adaptive optics (MagAO-X) instrument is a new extreme adaptive optics (ExAO) system designed for operation in the visible to near-IR which will deliver high contrast-imaging capabilities. The main AO system will be driven by a pyramid wavefront sensor (PyWFS); however, to mitigate the impact of quasi-static and non-common path (NCP) aberrations, focal plane wavefront sensing (FPWFS) in the form of low-order wavefront sensing (LOWFS) and spatial linear dark field control (LDFC) will be employed behind a vector apodizing phase plate (vAPP) coronagraph using rejected starlight at an intermediate focal plane. These techniques will allow for continuous high-contrast imaging performance at the raw contrast level delivered by the vAPP coronagraph 6 x 10^-5. We present simulation results for LOWFS and spatial LDFC with a vAPP coronagraph, as well as laboratory results for both algorithms implemented with a vAPP coronagraph at the University of Arizona Extreme Wavefront Control Lab., Comment: 17 pages, 22 figures

MagAO-X is an entirely new extreme adaptive optics system for the Magellan Clay 6.5 m telescope, funded by the NSF MRI program starting in Sep 2016. The key science goal of MagAO-X is high-contrast imaging of accreting protoplanets at Hα. With 2040 actuators operating at up to 3630 Hz, MagAO-X will deliver high Strehls (> 70%), high resolution (19 mas), and high contrast (< 1 × 10^(-4)) at Hα (656 nm). We present an overview of the MagAO-X system, review the system design, and discuss the current project status.

Recurrence Quantification Analysis (RQA) is a non-linear time series analysis technique widely employed in many different research fields. Among the many applications of this method, it has been shown that it can be successfully employed in the detection of small signals embedded into noise. In this work we explore the possibility of using the RQA in astronomical high contrast imaging, for the detection of faint objects nearby bright sources in very high frame rate (1 KHz) data series. For this purpose, we used a real 1 kHz image sequence of a bright star, acquired with the SHARK-VIS forerunner at LBT. Our results show excellent performances in terms of detection contrasts even with a very short data sequence (a few seconds). The use of RQA in astronomical high contrast imaging is discussed in light of the possible science applications and with respect to other techniques like, for example, the angular differential imaging (ADI) or the Speckle-Free ADI (SFADI).

As astronomers, we are living an exciting time for what concerns the search for other worlds. Recent discoveries have already deeply impacted our vision of planetary formation and architectures. Future bio-signature discoveries will probably deeply impact our scientific and philosophical understanding of life formation and evolution. In that unique perspective, the role of observation is crucial to extend our understanding of the formation and physics of giant planets shaping planetary systems. With the development of high contrast imaging techniques and instruments over more than two decades, vast efforts have been devoted to detect and characterize lighter, cooler and closer companions to nearby stars, and ultimately image new planetary systems. Complementary to other planet-hunting techniques, this approach has opened a new astrophysical window to study the physical properties and the formation mechanisms of brown dwarfs and planets. I will briefly review the different observing techniques and strategies used, the main samples of targeted stars, the key discoveries and surveys, to finally address the main results obtained so far about the physics and the mechanisms of formation and evolution of young giant planets and planetary system architectures.

The High Contrast spectroscopy testbed for Segmented Telescopes (HCST) is being developed at Caltech. It aims at addressing the technology gap for future exoplanet imagers and providing the U.S. community with an academic facility to test components and techniques for high contrast imaging, focusing on segmented apertures proposed for future ground-based (TMT, ELT) and space-based telescopes (HabEx, LUVOIR). We present an overview of the design of the instrument and a detailed look at the testbed build and initial alignment. We offer insights into stumbling blocks encountered along the path and show that the testbed is now operational and open for business. We aim to use the testbed in the future for testing of high contrast imaging techniques and technologies with amongst with thing, a TMT-like pupil.

Currently, linear state space modeling is used for focal plane wavefront estimation and control of high-contrast imaging system. Although this framework has made great strides in the past decades, it fails to track the nonlinearities from the deformable mirrors and the light propagation, which to some extent influences the accuracy of the electric field estimation and the speed and robustness of the controller. In this paper, we propose the application of neural networks to identify and optimally control a high-contrast imaging system. Based on the E-M algorithm and reinforcement learning techniques, we develop a new nonlinear system identificaton method and a corresponding nonlinear neural network controller. Simulation and experimental results from Princetons High Contrast Imaging Lab (HCIL) are reported to demonstrate the utility of this algorithm.

SHARK-VIS, the LBT forthcoming high-contrast imager, is undergoing its fabrication phase and will see its first light in Q4-2019. By exploiting the outstanding performance of the LBT SOUL adaptive optics in the range of wavelength from 400 to 1000 nm, the instrument is expected to provide breakthrough science results in different fields, from exoplanets detection and characterization, to star formation with resolutions around 15mas and a contrast larger than 1e-5 at 100mas of separation. This will be possible thanks to the unprecedented performances of the LBT extreme AO system and the instrument fast-frame-rate acquisition as already demonstrated by preliminary tests on-sky. In this contribution, we will review the main technical aspects of the instrument and present the current project status.

The success of ground-based, high contrast imaging for the detection of exoplanets in part depends on the ability to differentiate between quasi-static speckles caused by aberrations not corrected by adaptive optics (AO) systems, known as non-common path aberrations (NCPAs), and the planet intensity signal. Frazin (ApJ, 2013) introduced a post-processing algorithm demonstrating that simultaneous millisecond exposures in the science camera and wavefront sensor (WFS) can be used with a statistical inference procedure to determine both the series expanded NCPA coefficients and the planetary signal. We demonstrate, via simulation, that using this algorithm in a closed-loop AO system, real-time estimation and correction of the quasi-static NCPA is possible without separate deformable mirror (DM) probes. Thus the use of this technique allows for the removal of the quasi-static speckles that can be mistaken for planetary signals without the need for new optical hardware, improving the efficiency of ground-based exoplanet detection. In our simulations, we explore the behavior of the Frazin Algorithm (FA) and the dependence of its convergence to an accurate estimate on factors such as Strehl ratio, NCPA strength, and number of algorithm search basis functions. We then apply this knowledge to simulate running the algorithm in real-time in a nearly ideal setting. We then discuss adaptations that can be made to the algorithm to improve its real-time performance, and show their efficacy in simulation. A final simulation tests the technique's resilience against imperfect knowledge of the AO residual phase, motivating an analysis of the feasibility of using this technique in a real closed-loop Extreme AO system such as SCExAO or MagAO-X, in terms of computational complexity and the accuracy of the estimated quasi-static NCPA correction., Comment: 10 pages, 6 figures

MWC758 is a young star surrounded by a transitional disk. Recently, a protoplanet candidate has been detected around MWC758 through high-resolution $L'$-band observations. The candidate is located inside the disk cavity at a separation of $\sim$111 mas from the central star, and at an average position angle of $\sim$165.5 degrees. We have performed simultaneous adaptive optics observations of MWC758 in the H$_{\alpha}$ line and the adjacent continuum using SPHERE/ZIMPOL at the Very Large Telescope (VLT). We aim at detecting accreting protoplanet candidates through spectral angular differential imaging observations. The data analysis does not reveal any H$_{\alpha}$ signal around the target. The derived contrast curve in the B_Ha filter allows us to derive a 5$\sigma$ upper limit of $\sim$7.6 mag at 111 mas, the separation of the previously detected planet candidate. This contrast translates into a H$_{\alpha}$ line luminosity of $L_{\rm H_{\alpha}}\lesssim$ 5$\times$10$^{-5}$ $L_{\odot}$ at 111 mas, and an accretion luminosity of $L_{acc}, Comment: 5 pages, accepted for publication in A&A letters

NASA WFIRST mission has planned to include a coronagraph instrument to find and characterize exoplanets. Masks are needed to suppress the host star light to better than 10-8 – 10-9 level contrast over a broad bandwidth to enable the coronagraph mission objectives. Such masks for high contrast coronagraphic imaging require various fabrication technologies to meet a wide range of specifications, including precise shapes, micron scale island features, ultra-low reflectivity regions, uniformity, wave front quality, etc. We present the technologies employed at JPL to produce these pupil plane and image plane coronagraph masks, and lab-scale external occulter masks, highlighting accomplishments from the high contrast imaging testbed (HCIT) at JPL and from the high contrast imaging lab (HCIL) at Princeton University. Inherent systematic and random errors in fabrication and their impact on coronagraph performance are discussed with model predictions and measurements.

We report a new turn-on substrate probe whose intense fluorescent reporter signature is selectively provided upon probe activation by the cancer-associated oxidoreductase, hNQO1. The extremely high fluorescence turn-on of the probe was utilized to generate fluorescence microscope images of hNQO1-expressing, tumor-derived colorectal and ovarian cancer cells with unprecedented positive signal-to-negative background ratios (PNRs), a key step toward probe application in guided surgical removal of diseased tissues.

We present observations of nearby red supergiants with SPHERE.

Photoacoustic imaging (PAI) has evolved to a stage that high-performance exogeneous contrast agents are urgently needed for imminent biomedical and clinical applications. Given that a material meets the basic criteria of efficient photoacoustic conversion, high biocompatibility, and fast excretion, great effort has been devoted to evaluating various materials for developing advantageous contrast agents to explore the full potentials of PAI. One focus is through modification of the current agents to boost their PA performance; whilst the other focus is to develop novel agents. Antimonene (AM) has emerged as a promising candidate for next generation of electronics among 2D materials due to its outstanding properties. Herein, it is reported that liquid-phase exfoliated antimonene exhibits extraordinary photoacoustic performance, which is not only more advantageous than other 2D materials, such as black phosphorus, graphene oxide, and transition metal dichalcogenides, but also superior to the commonly used PA contrast agents, such as ICG and gold nanorods. An insight analysis reveals that the unique thermal property of AM, including intrinsic low thermal conductivity and the morphology-related high interfacial thermal conductivity, might interpret the high photothermal conversion efficiency, and thus the excellent photoacoustic performance. The prodigious performance allows sensitive monitoring of intracellular events and high-quality in vivo tumor imaging.

Context. The effects of a planet sculpting the disk from which it formed are most likely to be found in disks that are in transition between being classical protoplanetary and debris disks. Recent direct imaging of transition disks has revealed structures such as dust rings, gaps, and spiral arms, but an unambiguous link between these structures and sculpting planets is yet to be found. Aims: We aim to find signs of ongoing planet-disk interaction and study the distribution of small grains at the surface of the transition disk around RX J1615.3-3255 (RX J1615). Methods: We observed RX J1615 with VLT/SPHERE. From these observations, we obtained polarimetric imaging with ZIMPOL (R'-band) and IRDIS (J), and IRDIS (H2H3) dual-band imaging with simultaneous spatially resolved spectra with the IFS (YJ). Results: We image the disk for the first time in scattered light and detect two arcs, two rings, a gap and an inner disk with marginal evidence for an inner cavity. The shapes of the arcs suggest that they are probably segments of full rings. Ellipse fitting for the two rings and inner disk yield a disk inclination I = 47 ± 2° and find semi-major axes of 1.50 ± 0.01'' (278 au), 1.06 ± 0.01'' (196 au) and 0.30 ± 0.01'' (56 au), respectively. We determine the scattering surface height above the midplane, based on the projected ring center offsets. Nine point sources are detected between 2.1'' and 8.0'' separation and considered as companion candidates. With NACO data we recover four of the nine point sources, which we determine to be not co-moving, and therefore unbound to the system. Conclusions: We present the first detection of the transition disk of RX J1615 in scattered light. The height of the rings indicate limited flaring of the disk surface, which enables partial self-shadowing in the disk. The outermost arc either traces the bottom of the disk or it is another ring with semi-major axis ≳ 2.35'' (435 au). We explore both scenarios, extrapolating the complete shape of the feature, which will allow us to distinguish between the two in future observations. The most attractive scenario, where the arc traces the bottom of the outer ring, requires the disk to be truncated at r ≈ 360 au. If the closest companion candidate is indeed orbiting the disk at 540 au, then it would be the most likely cause for such truncation. This companion candidate, as well as the remaining four, all require follow up observations to determine if they are bound to the system. Based on observations made with ESO Telescopes at the La Silla Paranal Observatory under programme IDs 095.C-0298(A), 095.C-0298(B), and 095.C-0693(A) during guaranteed and open time observations of the SPHERE consortium, and on NACO observations: program IDs: 085.C-0012(A), 087.C-0111(A), and 089.C-0133(A). The reduced images as FITS files are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/595/A114

Transition disks, protoplanetary disks with inner clearings, are promising objects in which to directly image forming planets. The high contrast imaging technique of non-redundant masking is well posed to detect planetary mass companions at several to tens of AU in nearby transition disks. We present non-redundant masking observations of the T Cha and LkCa 15 transition disks, both of which host posited sub-stellar mass companions. However, due to a loss of information intrinsic to the technique, observations of extended sources (e.g. scattered light from disks) can be misinterpreted as moving companions. We discuss tests to distinguish between these two scenarios, with applications to the T Cha and LkCa 15 observations. We argue that a static, forward-scattering disk can explain the T Cha data, while LkCa 15 is best explained by multiple orbiting companions., Comment: SPIE conference proceeding

Over 3000 exoplanets and hundreds of exoplanetary systems have been detected to date and we are now rapidly moving toward an era where the focus is shifting from detection to direct imaging and spectroscopic characterization of these new worlds and their atmospheres. NASA is currently studying several exoplanet characterization mission concepts for the 2020 Decadal Survey ranging from probe class to flagships. Detailed and comprehensive exoplanet characterization, particularly of exo-Earths, leading to assessment of habitability, or indeed detection of life, will require significant advances beyond the current state-of-the-art in high contrast imaging and starlight suppression techniques which utilize specially shaped precision optical elements to block the light from the parent star while controlling scattering and diffraction thus revealing and enabling spectroscopic study of the orbiting exoplanets in reflected light. In this paper we describe the two primary high contrast starlight suppression techniques currently being pursued by NASA: 1) coronagraphs (including several design variations) and 2) free-flying starshades. These techniques are rapidly moving from the technology development phase to the design and engineering phase and we discuss the prospects and projected performance for future exoplanet characterization missions utilizing these techniques coupled with large aperture telescopes in space.

The SPEED project - the Segmented Pupil Experiment for Exoplanet Detection - in development at the Lagrange laboratory, aims at gearing up strategies and technologies for high-contrast instrumentation with segmented telescopes. This new instrumental platform offers an ideal environment in which to make progress in the domain of ELTs and/or space-based missions with complex apertures. It combines all the required recipes (phasing optics, wavefront control/shaping, and advanced coronagraphy) to get to very close angular separation imaging. In this paper, we report on the optical design and subsystems advances and we provide a progress overview.

We introduce a new technological framework for high-contrast coronagraphy, namely digital adaptive coronagraphy (DAC) using spatial light modulators (SLMs), taking advantage of recent advances in this technology. We present proof-of-principle experimental results in the visible, using a transmissive twisted nematic liquid crystal SLM display to show that SLMs can be successfully implemented as focal-plane phase-mask coronagraphs (4QPM, 8OPM,...), and that the technology is essentially in place to address realistic instrumental configurations. We explore a specific application where SLM-based adaptive coronagraphy might be particularly competitive, which is direct imaging of multiple stars systems, by simultaneously nulling multiple point sources in the field. Using a simple approach to compute a brightness-weighted synthetized coronagraphic phase map, we show that in the case of binaries the contrast gain over using a regular phase map can exceed 4 stellar magnitudes for a 1:1 binaries down to separation as close as 1 λ/D. Thanks to video-rate update frequency of the SLM, the technique is in principle compatible with sky rotation in the case of altitude-azimuth telescope mounts, and can address multiple target configurations with no actual mechanical or hardware change.

The discovery of thousands of exoplanets is generating increasing interest in the direct imaging and characterization of these planets. Starshade, an external occulter, could fly in formation between a telescope and distant star, blocking out the light from the star, and enabling us to focus on the light of any orbiting planets. Recent technology developments in coordination with system level design, has added much needed detail to define the technology requirements for a science mission that could launch in the 2020’s. This paper addresses the mechanical architecture, the successful efforts to date, the current state of design for the mechanical system, and upcoming technology efforts.

International audience; The SPHERE (Spectro-Polarimetric High-contrast Exoplanet Research) instrument aims at detecting extremely faint sources (giant extrasolar planets) in the vicinity of bright stars1. Such a challenging goal requires the use of a very-high-order performance Adaptive Optics [AO] system feeding the scientific instruments with a quasi-perfect flat wave front corrected from all the atmospheric turbulence and internal defects. This AO system, called SAXO (Sphere Ao for eXoplanet Observation) is the heart of the instrument, a heart beating 1200 time per second and providing unprecedented image quality for a large ground based telescope at optical/near infrared wavelength. We will present the latest results obtained on-sky, demonstrating its exceptional performance (in terms of correction quality, stability and robustness) and tremendous potentiality for high contrast imaging and more specifically for exoplanet discovery.

The development of adaptive optics (AO) played a major role in modern astronomy over the last three decades. By compensating for the atmospheric turbulence, these systems enable to reach the diffraction limit on large telescopes. In this review, we will focus on high contrast applications of adaptive optics, namely, imaging the close vicinity of bright stellar objects and revealing regions otherwise hidden within the turbulent halo of the atmosphere to look for objects with a contrast ratio lower than 10^-4 with respect to the central star. Such high-contrast AO-corrected observations have led to fundamental results in our current understanding of planetary formation and evolution as well as stellar evolution. AO systems equipped three generations of instruments, from the first pioneering experiments in the nineties, to the first wave of instruments on 8m-class telescopes in the years 2000, and finally to the extreme AO systems that have recently started operations. Along with high-contrast techniques, AO enables to reveal the circumstellar environment: massive protoplanetary disks featuring spiral arms, gaps or other asymmetries hinting at on-going planet formation, young giant planets shining in thermal emission, or tenuous debris disks and micron-sized dust leftover from collisions in massive asteroid-belt analogs. After introducing the science case and technical requirements, we will review the architecture of standard and extreme AO systems, before presenting a few selected science highlights obtained with recent AO instruments.

In the framework of the SHARK project the visible channel is a novel instrument synergic to the NIR channel and exploiting the performances of the LBT XAO at visible wavelengths. The status of the project is presented together with the design study of this innovative instrument optimized for high contrast imaging by means of high frame rate. Its expected results will be presented comparing the simulations with the real data of the “Forerunner” experiment taken at 630nm.

In this work we explore the possibility of using Recurrence Quantification Analysis (RQA) in astronomical high-contrast imaging to statistically discriminate the signal of faint objects from speckle noise. To this end, we tested RQA on a sequence of high frame rate (1 kHz) images acquired with the SHARK-VIS forerunner at the Large Binocular Telescope. Our tests show promising results in terms of detection contrasts at angular separations as small as $50$ mas, especially when RQA is applied to a very short sequence of data ($2$ s). These results are discussed in light of possible science applications and with respect to other techniques like, for example, Angular Differential Imaging and Speckle-Free Imaging., Comment: 12 pages, 9 figures, Accepted for publication in ApJ

Results from a groundbased high contrast imaging survey of thirteen nearby white dwarfs for substellar objects is presented. We place strict upper limits on the type of substellar objects present, ruling out the presence of anything larger than ∼14 MJup for eight of the white dwarfs at separations >19 AU and corresponding to primordial separations of ∼3-6 AU assuming adiabatic mass loss without tidal interactions. With these results we place the first upper limit on the number of intermediate mass stars with brown dwarfs at separations > 13 AU. We combine these results with previous work to place upper limits on the number of massive Jovian (> 10 MJup) planets in orbit around white dwarfs whose progenitors spanned a mass range of 1-7 M⊙.