Search

The phase distribution of lithiated LVO in thick (∼500 μm) porous electrodes (TPEs) designed to facilitate both ion and electron transport was determined using synchrotron-based operando energy dispersive X-ray diffraction (EDXRD). Probing 3 positions in the TPE while cycling at a 1C rate revealed a homogeneous phase transition across the thickness of the electrode at the 1st and 95th cycles. Continuum modelling indicated uniform lithiation across the TPE in agreement with the EDXRD results and ascribed decreasing accessible active material to be the cause of loss in delivered capacity between the 1st and 95th cycles. The model was supported by the observation of significant particle fracture by SEM consistent with loss of electrical contact. Overall, the combination of operando EDXRD, continuum modeling, and ex situ measurements enabled a deeper understanding of lithium vanadium oxide transport properties under high rate extended cycling within a thick highly porous electrode architecture.

One of the inherent challenges with Li-S batteries is polysulfide dissolution, in which soluble polysulfide species can contribute to the active material loss from the cathode and undergo shuttling reactions inhibiting the ability to effectively charge the battery. Prior theoretical studies have proposed the possible benefit of defective 2 D MoS2 materials as polysulfide trapping agents. Herein the synthesis and thorough characterization of hydrothermally prepared MoS2 nanosheets that vary in layer number, morphology, lateral size, and defect content are reported. The materials were incorporated into composite sulfur-based cathodes and studied in Li-S batteries with environmentally benign ether-based electrolytes. Through directed synthesis of the MoS2 additive, the relationship between synthetically induced defects in 2 D MoS2 materials and resultant electrochemistry was elucidated and described.

Molybdenum(IV) sulfide (MoS2) has generated significant interest as an electroactive material for Li-ion batteries because of its high theoretical capacity, good rate capability, and minimal volume...

Solid state batteries are an emerging alternative to traditional liquid electrolyte cells that provide potential for safe and high-energy density power sources. This report describes a self-forming, solid state battery based on the Li/I2 couple using an LiI-rich LiI(3-hydroxypropionitrile)2 electrolyte (LiI–LiI(HPN)2). As the negative and positive active materials are generated in situ, the solid electrolyte–current collector interfaces play a critical role in determining the electrochemical response of the battery. Herein, we report the investigation of solid electrolyte–current collector interfaces with a self-forming LiI–LiI(HPN)2 solid electrolyte and the role of varying interface design in reducing resistance during cycling.

Fe3O4 nanoparticles (NPs) with an average size of 8-10 nm have been successfully functionalized with various surface-treatment agents to serve as model systems for probing surface chemistry-dependent electrochemistry of the resulting electrodes. The surface-treatment agents used for the functionalization of Fe3O4 anode materials were systematically varied to include aromatic or aliphatic structures: 4-mercaptobenzoic acid, benzoic acid (BA), 3-mercaptopropionic acid, and propionic acid (PA). Both structural and electrochemical characterizations have been used to systematically correlate the electrode functionality with the corresponding surface chemistry. Surface treatment with ligands led to better Fe3O4 dispersion, especially with the aromatic ligands. Electrochemistry was impacted where the PA- and BA-treated Fe3O4 systems without the -SH group demonstrated a higher rate capability than their thiol-containing counterparts and the pristine Fe3O4. Specifically, the PA system delivered the highest capacity and cycling stability among all samples tested. Notably, the aromatic BA system outperformed the aliphatic PA counterpart during extended cycling under high current density, due to the improved charge transfer and ion transport kinetics as well as better dispersion of Fe3O4 NPs, induced by the conjugated system. Our surface engineering of the Fe3O4 electrode presented herein, highlights the importance of modifying the structure and chemistry of surface-treatment agents as a plausible means of enhancing the interfacial charge transfer within metal oxide composite electrodes without hampering the resulting tap density of the resulting electrode.

Solid electrolytes (SEs) are a promising, safe alternative to liquid electrolytes in high energy density batteries, but challenges, including low ionic conductivity and dendrite formation, remain. In a recent work, it was determined that dendrite formation within representative SEs, Li7La3Zr2O12 and Li3PS4, is due to their non-negligible electronic conductivity.[1] Notably, LiI has negligible electronic conductivity and thus the formation of lithium dendrites may be lessened, making LiI a good candidate for SE development. Our previous work on LiI SE, utilized 1:2 lithium iodide:3-hydroxypropionitrile (LiI(HPN)2) as a conductive additive, creating an 80/20 LiI/LiI(HPN)2 composite as a self-forming, rechargeable battery.[3] Additional work has demonstrated interfacial modification can effectively lower the cell impedance and improve coulombic efficiency (CE).[2, 4] In this work, a LiI SE was improved by reducing particle size via several processing methods; grinding (G), sonicating (C-S), and grinding with sonicating (G-S), and compared to a control (C) sample of LiI which underwent no processing. Partial hydration of LiI results in increased conductivity via increased defect density, and thus this parameter was controlled to ca. 34 mol% LiI monohydrate between samples. With further processing, particle size was reduced from 5 ± 1 µm to 2.0 ± 0.2 µm for the C and G-S samples. Utilized in 80/20 LiI/LiI(HPN)2 composites, reducing particle size resulted in an order of magnitude increase in ionic conductivity, from 7.7 x 10-8 to 6.1 x 10-7 S cm-1, at room temperature. Improved conductivity is attributed to an increased number of grain boundaries and defects, enabling ion transport and better mixing with the electrolyte additive, LiI(HPN)2. 3D confocal Raman spectroscopy in conjunction with non-negative matrix factorization (NMF) analysis determined the degree of HPN aggregation was lessened in the sample with smallest particle size. This LiI SE was utilized in a self-forming Li/I2 battery, where reduced particle size (improved conductivity) led to significantly reduced overpotential, allowing the coulombic efficiency to reach 100% in the first cycle. The G-S cells also exhibited improved electrochemical function when cycling at higher rates compared with the other electrolyte types. This work demonstrates the effect of particle size on solid electrolyte in a self-forming, self-healing, all solid state battery with a lithium metal negative electrode. References [1] F. Han, A.S. Westover, J. Yue, X. Fan, F. Wang, M. Chi, D.N. Leonard, N.J. Dudney, H. Wang, C. Wang, High electronic conductivity as the origin of lithium dendrite formation within solid electrolytes, Nature Energy, 4 (2019) 187-196. [2] C.A. Stackhouse, A. Abraham, S. Yan, L. Wang, N. Sadique, G. Singh, A.C. Marschilok, E.S. Takeuchi, K.J. Takeuchi, Self-Healing, Improved Efficiency Solid State Rechargeable Li/I2 Based Battery, Journal of The Electrochemical Society, 168 (2021). [3] A. Abraham, J. Huang, P.F. Smith, A.C. Marschilok, K.J. Takeuchi, E.S. Takeuchi, Communication—Demonstration and Electrochemistry of a Self-Forming Solid State Rechargeable LiI(HPN)2Based Li/I2Battery, Journal of The Electrochemical Society, 165 (2018) A2115-A2118. [4] A. Abraham, M.R. Dunkin, J. Huang, B. Zhang, K.J. Takeuchi, E.S. Takeuchi, A.C. Marschilok, Interface effects on self-forming rechargeable Li/I2-based solid state batteries, MRS Communications, 9 (2019) 657-662.