Search

Long-chain fatty acids (LCFA) are commonly found in lipid-rich wastewaters and are a key factor to monitor the anaerobic digesters. A new simple, fast, precise, and suitable method for routine analysis of LCFA is proposed. The system involves in-syringe-magnetic stirring-assisted dispersive liquid-liquid microextraction (DLLME) prior to gas chromatography-mass spectrometry (GC-MS) without a derivatization process. Calibration curves were prepared in an ethanol solution (R2 ≥ 0.996), which was also useful as disperser solvent. Hexane was chosen as the extraction solvent. Several parameters (pH, ionic strength, extraction solvent volume, stirring time) were optimized in multivariate and univariate studies. Limits of detection (LODs) were found in the range 0.01–0.05 mg L−1 and good precision inter-day (RSDs≤7.9%) and intra-day (RSDs≤4.4%) were obtained. The method was applied to quantify LCFA in supernatants of anaerobic digesters and olive mill wastewaters (OMW). Palmitic, stearic, and oleic acids were the most abundant fatty acid in the analyzed samples and the relative recoveries for all of them were between 81 and 113%.

This work review shows a description of non-chromatographic and chromatographic procedures proposed for speciation analysis of antimony employing hydride generation (HG) coupled to atomic fluorescence spectrometry (AFS) in environmental matrices, including details of HG-AFS as the detection technique. Non-chromatographic procedures have been developed based on the determination of total antimony after a pre-reduction step. The main reductant agents used are discussed. Antimony(III) has been quantified in the presence of a masking agent. The most used are citrate and 8-hydroquinoline. Chromatographic procedures have been established utilizing High-Performance Liquid Chromatography (HPLC). Advantages and drawbacks of the main extracting agents and mobile phases employed in these procedures have been discussed. Also, alternatives to improve the method sensitivity during the determination of antimony(V) and its organic compounds by HPLC-HG-AFS are presented. Speciation procedures involving preconcentration steps have allowed methods with high sensitivity. Tables evidencing applications of non-chromatographic and chromatographic procedures in speciation studies of environmental samples are also shown. Advantages of automated and flow systems for antimony speciation studies are also highlighted.

A Multi-Syringe Flow Injection Analysis (MSFIA) fluorometric system based on a 3D printing device hosting a CCD detector has been designed for the determination of quinine in soft drinks. A LED controlled by an electronic circuit was used as a radiation source. The entire system is connected to two USB outputs of a computer. The AutoAnalysis program has been used for data acquisition and treatment. The results are more accurate and precise than those obtained with a manual method using a conventional spectrofluorometer. This developed system is a viable alternative to reduce the consumption of reagents, the impact on the environment and reduce measurement costs.

A simple potentiometric chip-based multipumping flow system (MPFS) has been developed for the simultaneous determination of fluoride, chloride, pH, and redox potential in water samples. The proposed system was developed by using a poly(methyl methacrylate) chip microfluidic-conductor using the advantages of flow techniques with potentiometric detection. For this purpose, an automatic system has been designed and built by optimizing the variables involved in the process, such as: pH, ionic strength, stirring and sample volume. This system was applied successfully to water samples getting a versatile system with an analysis frequency of 12 samples per hour. Good correlation between chloride and fluoride concentration measured with ISE and ionic chromatography technique suggests satisfactory reliability of the system.

International audience; 15 The present paper reports the development and the application of a microplate assay for the fast 16 and individual determination of thiols and sulfides. The method is based on the reaction of ethyl 17 propiolate with thiols and sulfides, yielding thioacrylates absorbing in the UV range. 18 Thioacrylate generated by derivation of sulfide with EP presents a bathochromic shift of 19 maximal absorbance wavelength of 16 nm compared to thioacrylates formed with thiols. EP 20 concentration, reaction time and derivatization pH were carefully optimized in order to 21 separately quantify thiols and sulfides using a spectral deconvolution procedure in 15 minutes. 22 The detection limits were 0.6 and 2.8 µM (63.7 and 92.4 µg.L-1) for mercaptopropionic acid 23 (used as reference thiol compound for calibration) and dissolved hydrogen sulfide respectively. 24 Non-thiol sulfur compounds (methionine, sulfates and sulfites) or other nucleophile compound 25 did not display any interference in the determination of MPA or sulfides. Interference from 26 metals was suppressed with application of a reduction step with TCEP and DTPA. Finally, the 27 method has been successfully applied to the analysis of raw and treated wastewater. 28 29

Dietary supplements may contain heavy metals with the property of bioaccumulation in humans. The aim of this research was to validate and apply two analytical methods to determine Pb, As, Cr, and Hg in dietary supplements by Total Reflection X-ray Fluorescence Spectroscopy (TXRF). Methods validation was conducted through a multivariate analysis using a central composite design (CCD) and a desirability function. Critical values for each study variable were established. The TXRF_DS_1 method was proposed for Pb, As, and Cr determinations, while the TXRF_DS_2 was established for Hg analysis. The digestion method with an acid mixture (HNO3 + HCl + H2O2) was used to break down the organic material of dietary supplements. A solution of 10 μg L−1 Ga was used as an internal standard. Excellent analytical performance was obtained as LODs of 0.59, 0.41, 0.57, and 0.75 μg L−1 and LOQs of 1.95, 1.35, 1.90, and 2.50 μgL −1 for Pb, As, Cr, and Hg, respectively. Calibration curves showed a good linearity for all elements (R2>0.999). Excellent accuracy and precision in measurements (% RSD) was achieved. The real and spiked samples analysis demonstrated the applicability of the TXRF technique (percentage recovery 91–108%). Besides, two samples were analyzed in a comparison study between the TXRF_DS_1 method and the ICP-OES method. The results obtained showed good agreement between both techniques. The TXRF technique allows the analysis of toxic heavy metals in dietary supplements, which are marketed in a wide variety of presentations.

Volatile fatty acids (VFAs) are key parameters to monitor anaerobic digestion processes. Thus, a fast, simple and precise determination of these analytes is necessary for a timely characterization of the biological processes present in municipal solid waste and wastewater treatment plants. In this work, an automated method for the extraction and preconcentration of VFAs, based on dispersive liquid-liquid microextraction with magnetic stirring in syringe, and gas chromatography with flame ionization detector for the separation and detection, is described. The effect of parameters such as the type and volume of extraction solvent, pH, salting out effect and stirring time, was studied using a multivariate and univariate experimental design. Extraction and preconcentration were performed simultaneously using tert-butyl methyl ether (TBME) as the extraction solvent, after stirring 100 s at a constant rate. The detection limits were in the range of 0.1 - 1.3 mg L-1 and a good linearity was observed up to 1000 mg L-1 of the studied VFAs, with a range of R2 between 0.9997 and 0.9999. The intra and interday precision expressed as relative standard deviation (n= 5) varied between 0.7 and 2.4% and between 1.7 and 7.0%, respectively. Subsequently, the developed method was successfully applied to evaluate the presence of VFAs in wastewater samples from anaerobic treatments and an average relative recovery of 102% was obtained.

Corn is one of the most consumed cereals in world and the second most cultivated in Brazil. Cereal flour has a flavor well accepted by the Brazilian population. This work describes the preparation and characterization of a new corn flour reference material which can be used as a quality assurance tool to demonstrate the reliability of the analytical results obtained from inorganic analysis of cereals and their derivatives. The studied elements were Ca, K, Mg, P, Cu, Fe, Mn and Zn. Homogeneity and stability tests, material characterization and attribution of uncertainty value were performed in this work by following recommendations of ISO Guides 30–35. The material was shown to be homogeneous and stable for 15 months at temperatures of −10 °C, +25 °C and +45 °C, with small uncertainty. Alternatively, the data were analyzed by hierarchical clustering technique and the stability was confirmed. The confidence ellipse technique enabled a simple and fast evaluation of data supplied by collaborating laboratories allowing the exclusion of outlying values and indicating possible causes of the deviations.

The spectrophotometric determination of uranium (VI) has been developed using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP). This reaction has been adapted to apply a multisyringe flow injection analysis (MSFIA) system with spectrophotometric detection. The ternary complex of uranium (VI)-(Br-PADAP)-F has been measured at 578 nm. The procedure was optimized using univariate method and two-level full factorial. Four variables (concentrations of Br-PADAP, CyDTA, NaF and sample volume) were regarded as factors in the extraction optimization. Results of the two-level full factorial design, showed that only two factors (concentration of Br-PADAP and CyDTA) are statistically significant. The calibration curve is linear over the range 0.3–5 mg L−1 uranium (VI) with a relative standard deviation of 4.0% (1 mg L−1 uranium (VI), n = 10). The recoveries of uranium in water samples were between 80 and 102%.

International audience; This paper presents a simple, accurate and multi-sample method for the determination of volatile fatty acids (VFAs) thanks to a 96-well microplate technique. A procedure using an activating reagent of the carboxylic function (water-soluble carbodiimide EDC) and a fluorescent amino labeling reagent (N-(1-naphthyl)ethylenediamine, EDAN) allows the formation of an isoindole derivative that needs to be separated from initial fluorescent amine for efficient VFAs determination. Isolation of these fluorescent VFA-derivatives was carried out by use of the fluorescent quenching of EDAN with o-phthaldialdehyde (OPA). Quenching was most efficient at pH around 7 and by heating at 40 degrees C within the microplate reader. This optimized procedure has been applied to various carboxylic acids and other organic compounds, demonstrating that VFA exhibit the highest fluorescence responses with homogeneous results for the main ones (acetic, propionic and butyric acid, all mass concentration expressed as acetic acid equivalents). This protocol was calibrated against acetic acid and determination of VFA was thus possible in the range 3.9-2000 mg L-1 (acetic acid equivalents). Subsequent application to real samples (sewage sludges or anaerobically digested samples) and comparison to gas chromatography analyses gave accurate results, proving the great potential of our high-throughput microplate-based technique for the analysis of VFA. (C) 2011 Elsevier B.V. All rights reserved.

Correspondance auteur: Boudenne J.L. E-mail: jean-luc.boudenne@univ-provence.fr; International audience; This paper presents a simple, rapid, and accurate method suitable for on-site measurement of short-chain volatile fatty acids (SCFA) in various environmental samples. This fluorimetric method involves a derivatization step of SCFA with N-(1-naphthyl)ethylenediamine (EDAN) and allows determination of acetic, butyric, propionic, valeric, lactic, succinic, and p-hydroxybenzoic acids in approximatively 10 min. To evaluate specificity and accuracy of the method, both laboratory-made waters and real samples ranging from wastewater plant and river to soils and composts have been tested. Good accuracy and correlation (r(2) = 0.9887) with HPIC determination have been obtained. The potential interference effect has been taken into account with compounds like humic substances, alcohols, amines, aldehydes, and metallic ions. Ibis method seems thus well designed for the determination of total SCFA in waters, in the range 0.84-500 mg/L. Because this method seems well suited for following of anaerobic treatment, it has been calibrated versus acetic acid-equivalent