Search

Biofilm carriers, named ‘biocarriers’, are solids that allow the good attachment of microbes during wastewater treatment. Biocarriers also act as redox mediators to speed up the biotransformation of contaminants in industrial effluents, yet it is challenging to choose a biocarrier material that achieves strong biofilm adhesion and high degradation rates. Here we review insoluble polymeric biocarriers with focus on selecting a biocarrier, biofilm growth, metabolic pathways, applications, surface modification, and composites. According to the efficiency to decrease the chemical oxygen demand, conventional and modified composite biocarriers are rated as following: polyvinyl alcohol > polyurethane > polyethylene > polypropylene, and polyvinyl alcohol > waste tire > polyurethane > polyethylene, respectively. We also discuss biological and physical fouling.

The wide application of 6:2 fluorotelomer sulfonate (6:2 FTS) and its precursors results in their ubiquitous occurrence in the environment. This study investigated the biotransformation of 6:2 FTS using fresh slurries collected from constructed wetland under aerobic and anoxic conditions. Biotransformation rates of 6:2 FTS was extremely slow under both aerobic and anoxic conditions. The analysis of transformation products showed that less than 0.7 mol% of initial concentration of 6:2 FTS was biotransformed under anoxic conditions. Effects of 6:2 FTS on the shifts in microbial community in wetland slurry during aerobic and anoxic transformation were evaluated using 16S rRNA gene amplicon sequencing. Under aerobic conditions, 6:2 FTS altered the microbial community structure, in which Methylocaldum (Gamma-proteobacteria) became the predominant genus after being exposed to 6:2 FTS. This means that Methylocaldum appears to have higher tolerance to 6:2 FTS and seems to be potential 6:2 FTS-degrading bacteria. Under anoxic transformation, only the genus Methanomethylovorans (Euryarchaeota) was increased remarkably in wetland slurry exposed to 6:2 FTS.

Pinpointing environmental antibiotic resistance (AR) hot spots in low-and middle-income countries (LMICs) is hindered by a lack of available and comparable AR monitoring data relevant to such settings. Addressing this problem, we performed a comprehensive spatial and seasonal assessment of water quality and AR conditions in a Malaysian river catchment to identify potential "simple" surrogates that mirror elevated AR. We screened for resistant coliforms, 22 antibiotics, 287 AR genes and integrons, and routine water quality parameters, covering absolute concentrations and mass loadings. To understand relationships, we introduced standardized "effect sizes" (Cohen's D) for AR monitoring to improve comparability of field studies. Overall, water quality generally declined and environmental AR levels increased as one moved down the catchment without major seasonal variations, except total antibiotic concentrations that were higher in the dry season (Cohen's D > 0.8, P < 0.05). Among simple surrogates, dissolved oxygen (DO) most strongly correlated (inversely) with total AR gene concentrations (Spearman's ρ 0.81, P < 0.05). We suspect this results from minimally treated sewage inputs, which also contain AR bacteria and genes, depleting DO in the most impacted reaches. Thus, although DO is not a measure of AR, lower DO levels reflect wastewater inputs, flagging possible AR hot spots. DO measurement is inexpensive, already monitored in many catchments, and exists in many numerical water quality models (e.g., oxygen sag curves). Therefore, we propose combining DO data and prospective modeling to guide local interventions, especially in LMIC rivers with limited data.

Antibiotic residues, antibiotic resistant bacteria (ARB) and antibiotic resistance genes (ARGs) are considered new classes of water contaminants due to their potential adverse effects on aquatic ecosystems and human health. This paper provides comprehensive data on the occurrences of 19 antibiotics, bacteria resistant to 10 antibiotics, and 15 ARGs in raw influent and different treatment stages of conventional activated sludge (CAS) and membrane bioreactor (MBR) systems. Seventeen out of the 19 target antibiotics were detected in raw influent with concentrations of up to ten micrograms per liter. Concentrations of antibiotics measured in the secondary effluent were much lower compared to those in the raw influent. Among the antibiotics, amoxicillin, azithromycin, ciprofloxacin, chloramphenicol, meropenem, minocycline, oxytetracycline, sulfamethazine and vancomycin had highest removal by CAS or MBR systems with median removal efficiency (RE) 70%, while trimethoprim and lincomycin were recalcitrant in the CAS system with median RE50%. Similarly, the target ARB and ARGs were omnipresent in the raw influent samples with average concentrations as high as 2.6 × 10

This study provided the first comprehensive data on the occurrence and removal of twenty-five target emerging contaminants (ECs) in a full-scale water reclamation plant (WRP) in the Southeast Asian region. Nineteen out of the twenty-five ECs were ubiquitously detected in raw influent samples. Concentrations of the detected ECs in raw influent samples ranged substantially from 44.3 to 124,966ng/L, depending upon the compound and sampling date. The elimination of ECs in full-scale conventional activated sludge (CAS) and membrane bioreactor (MBR) systems at a local WRP was evaluated and compared. Several ECs, such as acetaminophen, atenolol, fenoprofen, indomethacin, ibuprofen, and oxybenzone, exhibited excellent removal efficiencies (>90%) in biological wastewater treatment processes, while some of the investigated compounds (carbamazepine, crotamiton, diclofenac, and iopamidol) appeared to be persistent in the both CAS and MBR systems. Field-based monitoring results showed that MBR outperformed CAS in the elimination of most target ECs. The relationship between molecular characteristics of ECs (i.e. physicochemical properties and structural features) and their removal efficiencies during biological wastewater treatment was also elucidated. Excellent removal efficiencies (>90%) were often noted for ECs with the sole presence of electron donating groups (i.e. phenolic [OH], amine [NH2], methoxy [OCH3], phenoxy [OC6H5], or alkyl groups). Conversely, ECs with the absence of electron donating groups or the predominance of strong electron withdrawing groups (e.g. halogenated, carbonyl, carboxyl, and sulfonamide) tended to show poor removal efficiencies (

Landfill leachate could be a significant source of emerging contaminants (ECs) and antibiotic resistance genes (ARGs) into the environment. This study provides the first information on the occurrence of selected ECs and ARGs in raw leachate from 16-year old closed landfill site in Singapore. Among the investigated ECs, acetaminophen (ACT), bisphenol A (BPA), clofibric acid (CA), caffeine (CF), crotamiton (CTMT), diclofenac (DCF), N,N-diethyl-m-toluamide (DEET), gemfibrozil (GFZ), lincomycin (LIN), salicylic acid (SA), and sulfamethazine (SMZ) were the most frequently detected compounds in raw landfill leachate. The concentrations of detected ECs in raw landfill leachate varied significantly, from below quantification limit to 473,977 ng/L, depending on the compound. In this study, Class I integron (intl1) gene and ten ARGs were detected in raw landfill leachate. Sulfonamide resistance (sul1, sul2, and dfrA), aminoglycoside resistance (aac6), tetracycline resistance (tetO), quinolone resistance (qnrA), and intl1 were ubiquitously present in raw landfill leachate. Other resistance genes, such as beta-lactam resistance (blaNMD1, blaKPC, and blaCTX) and macrolide-lincosamide resistance (ermB) were also detected, detection frequency of50%. The removal of target ECs and ARGs by a full-scale hybrid constructed wetland (CW) was also evaluated. The vast majority of ECs exhibited excellent removal efficiencies (90%) in the investigated hybrid CW system. This hybrid CW system was also found to be effective in the reduction of several ARGs (intl1, sul1, sul2, and qnrA). Aeration lagoons and reed beds appeared to be the most important treatment units of the hybrid CW for removing the majority of ECs from the leachate.

Very little information on the occurrence and risk assessment of antibiotics in the aquatic environment is reported for Vietnam, where antibiotics are assumed to be omnipresent in urban canals and lakes at high concentrations due to the easy accessibility of antibiotics without doctor prescription. This study provides comprehensive analysis of the occurrence of 23 antibiotics in urban canals (To Lich and Kim Nguu) and lakes (West Lake, Hoan Kiem, and Yen So) in Hanoi, Vietnam. Of these 23 antibiotics, 18 were detected in urban canals at above 67.9% detection frequency (DF). The concentrations of detected antibiotics were in the range from below quantification limit (MQL) to almost 50,000 ng/L, depending on the compound and sampling site. In urban canals, median concentration of amoxicillin, erythromycin, and sulfamethoxazole was >1000 ng/L while other antibiotics such as ampicillin, chloramphenicol, clindamycin, sulfamethazine, tetracycline, tylosin and vancomycin were detected at median concentrations of

This article found mistakes and misunderstandings regarding the collection of occurrence data of antibiotics in surface freshwater from the previous literature. These mistakes and misunderstandings were corrected to avoid the propagation of inaccurate information in the scientific literature.

Picocyanobacteria are small cyanobacteria, being about 0.8–1.5 µm in size. They are present in freshwater environments all over the world and are known to cause harmful algal blooms, although their effects are not well understood. Algal blooms are important to manage because they threaten freshwater resources, with potentially severe effects on ecological and human health. There is also increased urgency due to urbanization and climate change trends which are expected to exacerbate these bloom dynamics. These changes are expected to especially favour picocyanobacteria groups, emphasizing the need for better characterization of their effects in the environment. In this study, we report the discovery that Synechococcus sp. could produce cylindrospermopsin (CYN) and anatoxin-a (ATX). This ability had never been previously reported for this species. Their toxin genes were also partial compared to other major producers such as Raphidiopsis sp. and Anabaena sp., demonstrating potentially unique synthesis pathways that provides insight into the various mechanisms of genetic variation that drives toxin synthesis. The Synechococcus sp. strains were found to produce about 9.0 × 10−5–6.8 × 10−4 fg CYN cell−1 and 4.7 × 10−4–1.5 × 10−2 fg ATX cell−1. The potential for Synechococcus sp. to be toxic highlights a global concern due to its widespread distribution, and through environmental trends that increasingly favour its productivity within freshwater systems around the world.

Very little information on the occurrence and fate of multiple classes of antimicrobials in the aquatic environment is reported for the Southeast Asian region. This study provides the first and comprehensive data on the occurrence of ten different classes of antimicrobials in wastewater samples for Singapore. Among the investigated antimicrobials, 19 out of 21 target compounds were detected in 100% of the collected raw influent samples. Concentrations of the detected antimicrobials in raw influent varied from 23.8 to 43,740 ng/L. Removal of antimicrobials by conventional activated sludge (CAS) and membrane bioreactor (MBR) systems at a local wastewater treatment plant was evaluated. MBR exhibited better performance over CAS for most target antimicrobials. Beta-lactam, glycopeptide, and fluoroquinolone classes were largely eliminated by biological wastewater treatment processes, whereas trimethoprim and lincosamides appeared to be persistent. Effects of physicochemical properties and chemical structures of target antimicrobials on their removal efficiencies/mechanisms during wastewater treatment process were also discussed.

A robust and sensitive analytical method was developed for the simultaneous analysis of 21 target antimicrobials in different environmental water samples. Both single SPE and tandem SPE cartridge systems were investigated to simultaneously extract multiple classes of antimicrobials. Experimental results showed that good extraction efficiencies (84.5–105.6%) were observed for the vast majority of the target analytes when extraction was performed using the tandem SPE cartridge (SB+HR-X) system under an extraction pH of 3.0. HPLC-MS/MS parameters were optimized for simultaneous analysis of all the target analytes in a single injection. Quantification of target antimicrobials in water samples was accomplished using 15 isotopically labeled internal standards (ILISs), which allowed the efficient compensation of the losses of target analytes during sample preparation and correction of matrix effects during UHPLC-MS/MS as well as instrument fluctuations in MS/MS signal intensity. Method quantification limit (MQL) for most target analytes based on SPE was below 5 ng/L for surface waters, 10 ng/L for treated wastewater effluents, and 15 ng/L for raw wastewater. The method was successfully applied to detect and quantify the occurrence of the target analytes in raw influent, treated effluent and surface water samples.

The development of analytical methods for the detection and accurate quantification of algal toxins is of importance to assess the health risk of exposure to algal toxins in freshwater sources. This study established a sensitive and accurate analytical method for the quantification of 13 algal toxins (microcystins and nodularin) based on solid phase extraction (SPE) coupled with UPLC-MS/MS, in which 15N-microcystins were used as surrogate/internal standards. SPE method was optimized to extract the target algal toxins in freshwater samples. Good SPE efficiencies (84–96%) were achieved for the overwhelming majority of the investigated algal toxins when SPE was performed using HLB (500 mg, 6 mL) under alkaline conditions (pH 11). An accurate quantitative analysis of the algal toxins in real freshwater samples was performed by using 15N-labelled microcystins as isotopically labelled internal standards (ILISs), which compensated for the loss of target toxins during the whole analytical process. In addition, ILISs also helped to correct the effects of environmental matrices and instrument fluctuation in UPLC-MS/MS analysis. The limit of method quantification (MQL) for the algal toxins was

Analytical methods based on direct injection (DI) and solid phase extraction (SPE) coupled with ultrahigh performance liquid chromatography-tandem mass spectrometry (UPLC- MS/MS) were developed for the determination of anatoxin-a (ATX-a), cylindrospermopsin (CYN), and homoanatoxin-a (HATX-a) in freshwater samples impacted with cyanobacterial blooms. The presence of CYN in freshwater samples was detected and quantified based on direct injection method, while ATX-a and HATX-a could be determined by both DI and SPE-based methods. Matrix effects (ME) on the signal intensity of the cyanotoxins were systematically evaluated for both direct injection and SPE extract samples. CYN, ATX-a, and HATX-a suffered a significant suppression during UPLC-MS/MS. The selection of internal standards (ISs) for compensating/correcting the losses of target cyanotoxins during sample preparation and matrix effects in UPLC-MS/MS analyses were systematically evaluated. Acetaminophen-d4 (an isotopically labelled acetaminophen) is a suitable internal standard for correcting the ME on the signal intensity of ATX-a and HATX-a, while the use of L-phenylalanine-d5 or caffeine-d9 as IS for correcting ME of these toxins was not efficient, as expected. The method detection limit (MDL) for the target cyanotoxins ranged from 0.6 to 15 ng/L, which is sensitive enough to detect the presence of these toxins in cyanobacterial bloom freshwater. The developed methods were successfully applied for routine monitoring of the occurrence of these cyanotoxins in a local water body in Singapore. Monitoring results depicted that ATX-a, CYN and HATX-a were ubiquitously detected in water samples, at concentrations ranging from 70 to 24,600 ng/L.

A sensitive quantification method using pressurized liquid extraction (PLE) and solid phase extraction (SPE) coupled with ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) was developed for determination of 19 anthelmintic drugs (ADs) belonging to seven structural groups (Benzimidazoles, Diphenylsulfides, Imidazothiazoles, Hexahydropyrazines, Macrocylic lactones, Salicylanilides, Tetrahydropyrimidines) in environmental water and sediment samples. Eleven SPE cartridges, sample pH, elution solvents were tested to determine the optimal conditions for extraction. Among these investigated SPE types, the best recoveries for 19 target ADs were obtained from Oasis HLB cartridge with 37-102%, 45-103%, 37-88%, 28-82% and 31-90% for spiked river water, tap water, rainwater, wastewater, and sediment respectively (with RSD 15%), except for closantel. The 19 ADs were separated within 10 min by a BEH C18 column and monitored in both positive and negative ions modes with switching electrospray ionization source. The cross-talk interferences were solved by identification of secondary mass spectrum of substances through MRM-IDA-EPI scanning using Qtrap. These interference peaks could be efficiently eliminated by setting MRM segments or using Qtrap to obtain tertiary fragmented information. The developed methods were satisfactory in terms of linearity, accuracy, and precision, and used eight isotopically labeled compounds as internal standards to correct matrix effects. Method quantification limit (MQL) for 19 ADs was below 1.1 ng/L, 0.4 ng/L, 5.4 ng/L and 2.3 ng/g for river water, tap water, wastewater, and sediment, respectively. The validated method was successfully used to investigate the occurrence of anthelmintics in water and sediment samples from Chengdu, China. All ADs were detected in environment with the concentrations at ng/L level.

Ecotoxicological risks of perfluoroalkyl and polyfluoroalkyl substances (PFASs) in surface waters are difficult to model because data on PFASs distribution in multiple compartments (sediments, suspended particles and aqueous phase) are difficult to predict. This study quantified the distribution of 21 PFASs including PFCAs: C6-C13 perfluoroalkyl carboxylates, C4, C6, C8 and C10 perfluoroalkane sulfonates, 5 perfluorooctane sulfonamide substances (FOSAMs, including EtFOSA, FOSA, MeFOSAA, EtFOSAA, FOSAA), 2 N-alkyl perfluoroalkane sulfonamidoethanols (MeFOSE and EtFOSE), bis (perfluorooctyl) phosphinic acid (C8/C8 PFPIA), and 5:3 fluorotelomer carboxylic acid (5:3 acid) between bulk water and suspended particles in water column, and pore water and benthic sediments from a tropical urban water body. The distribution of PFASs between sorbed and dissolved phase was largely dependent on the perfluoroalkyl chain length (NCF2). PFCAs with NCF2 > 11 and perfluorodecane sulfonate (PFDS, NCF2 = 10) were found predominantly in the suspended particles and sediments. By contrast, short-chain PFASs (NCF2 ≤ 7) were detected predominantly in the dissolved phase. Sediment acts as a sink for long-chain PFASs while short-chain PFASs are more easily transported via the aqueous phase. Compared with benthic sediments, suspended particles, especially those in the top water layer, carried much higher concentrations of PFASs (by a factor of >100), indicating the stronger sorption capability of suspended particles. The wide variation in PFAS concentrations in suspended particles (∑PFASs concentrations: Log KD –desorption > Log KD –sorption > Log KD-SED) suggest that the distribution of PFASs in the field, especially between suspended particles and bulk water could not be well represented by lab results and that using the water concentrations in the bottom layer for estimation of pore water concentrations could lead to bias results.

Diffuse sources of pollution such as sewer leakages, sewer overflows, illicit discharges and stormwater runoff affect the urban surface water quality but often remain unknown. Therefore, the development of chemical markers for identifying and characterizing the origin of diffuse sources of pollution in urban surface waters is a requisite for protecting and managing urban water resources. In this study, the occurrence of 31 emerging contaminants (ECs) in untreated wastewater, treated wastewater, urban stormwater runoff, agricultural stormwater runoff, and freshwater bodies was investigated. Artificial sweeteners (ASs), pharmaceuticals and personal care products (PPCPs) were more frequently detected in the collected water samples. In raw wastewater, 21 target ECs were detected 100% in the collected samples with median concentrations ranging from 49.6 to 77,721 ng/L, while in freshwater bodies, only 13 compounds were found with detection frequency >50%. The median concentration of the majority of detected ECs in freshwater samples was below 100 ng/L. The suitability of ECs as chemical markers of diffuse sources in an urban watershed was assessed using a suite of criteria, including the detection frequency (DF), detection ratio (DR) (i.e. the ratio between median concentration and method quantification limit of a compound) and attenuation rates (i.e., biodegradation, sorption and abiotic degradation) in wastewater treatment processes. In addition, we propose a new key criterion, the concentration ratio (CR) of labile to conservative compounds, to evaluate the applicability of suitable chemical markers for source tracking. Using this new set of criteria (i.e. CR, DF, DR and attenuation rates), our analysis showed that among the investigated ECs, only acesulfame (ACE), acetaminophen (ACT), cyclamate (CYC), saccharin (SAC) were suitable as chemical markers of diffuse sources in surface waters. For caffeine (CF), N,N-diethyl-meta-toluamide (DEET), crotamiton (CTMT), triclocarban (TCC) and triclosan (TCS), their median concentration ratio to sucralose (SUC) in water bodies was consistently higher than that in raw wastewater, suggesting that these compounds might be unsuitable as chemical markers of sewage leakage in surface waters for this study area.

This study evaluated the geospatial distribution of fecal indicator bacteria (FIB) (i.e., Escherichia coli , Enterococcus spp.) and the alternative fecal indicator pepper mild mottle virus (PMMoV) in tropical freshwater environments under different land use patterns. Results show that the occurrence and concentration of microbial fecal indicators were higher for urban than for parkland-dominated areas, consistent with land use weightage. Significant positive correlations with traditional FIB indicate that PMMoV is a suitable indicator of fecal contamination in tropical catchments waters (0.549 ≤ rho ≤ 0.612; P < 0.01). PMMoV exhibited a strong significant correlation with land use weightage (rho = 0.728; P < 0.01) compared to traditional FIB (rho = 0.583; P < 0.01). In addition, chemical tracers were also added to evaluate the potential relationships with microbial fecal indicators. The relationships between diverse variables (e.g., environmental parameters, land use coverage, and chemical tracers) and the occurrence of FIB and PMMoV were evaluated. By using stepwise multiple linear regression (MLR), the empirical experimental models substantiate the impact of land use patterns and anthropogenic activities on microbial water quality, and the output results of the empirical models may be able to predict the sources and transportation of human fecal pollution or sewage contamination. In addition, the high correlation between PMMoV data obtained from quantitative real-time PCR (qPCR) and viral metagenomics data supports the possibility of using viral metagenomics to relatively quantify specific microbial indicators for monitoring microbial water quality (0.588 ≤ rho ≤ 0.879; P < 0.05). IMPORTANCE The results of this study may support the hypothesis of using PMMoV as an alternative indicator of human fecal contamination in tropical surface waters from the perspective of land use patterns. The predictive result of the occurrence of human fecal indicators with high accuracy may reflect the source and transportation of human fecal pollution, which are directly related to the risk to human health, and thereafter, steps can be taken to mitigate these risks.

Emerging contaminants, such as antibiotics, pharmaceuticals, personal care products, hormones, and artificial sweeteners, are recognized as new classes of water contaminants due to their proven or potential adverse effects on aquatic ecosystems and human health. This review provides comprehensive data on the occurrence of 60 emerging contaminants (ECs) in influent, treated effluent, sludge, and biosolids in wastewater treatment plants (WWTPs). In particular, data on the occurrence of ECs in the influents and effluents of WWTPs are systematically summarized and categorized according to geographical regions (Asia, Europe, and North America). The occurrence patterns of ECs in raw influent and treated effluents of WWTPs between geographical regions were compared and evaluated. Concentrations of most ECs in raw influent in Asian region tend to be higher than those in European and North American countries. Many antibiotics were detected in the influents and effluents of WWTPs at concentrations close to or exceeding the predicted no-effect concentrations (PNECs) for resistance selection. The efficacy of EC removal by sorption and biodegradation during wastewater treatment processes are discussed in light of kinetics and parameters, such as sorption coefficients (K d ) and biodegradation constants (k biol ), and physicochemical properties (i.e. log K ow and pK a ). Commonly used sampling and monitoring strategies are critically reviewed. Analytical research needs are identified, and novel investigative approaches for future monitoring studies are proposed.

Biofilm carriers play an important role in attached growth systems for wastewater treatment processes. This study systematically summarizes the traditional and novel biofilm carriers utilized in biofilm-based wastewater treatment technology. The advantages and disadvantages of traditional biofilm carriers are evaluated and discussed in light of basic property, biocompatibility and applicability. The characteristics, applications performance, and mechanism of novel carriers (including slow-release carriers, hydrophilic/electrophilic modified carriers, magnetic carriers and redox mediator carriers) in wastewater biological treatment were deeply analyzed. Slow release biofilm carriers are used to provide a solid substrate and electron donor for the growth of microorganisms and denitrification for anoxic and/or anaerobic bioreactors. Carriers with hydrophilic/electrophilic modified surface are applied for promoting biofilm formation. Magnetic materials-based carriers are employed to shorten the start-up time of bioreactor. Biofilm carriers acting as redox mediators are used to accelerate biotransformation of recalcitrant pollutants in industrial wastewater.

In the present study, the sorption and biodegradation characteristics of five pharmaceutical and personal care products (PPCPs), including acetaminophen (ACT), carbamazepine (CBZ), crotamiton (CTMT), diethyltoluamide (DEET) and salicylic acid (SA), were studied in laboratory-batch experiments. Sorption kinetics experimental data showed that sorption systems under this study were more appropriately described by the pseudo second-order kinetics with a correlation coefficient (R2) > 0.98. Sorption equilibrium data of almost all target compounds onto soil could be better described by the Freundlich sorption isotherm model. The adsorption results showed higher soil affinity for SA, following by ACT. Results also indicated a slight effect of pH on PPCP adsorption with lower pH causing lower adsorption of compounds onto the soil except for SA at pH 12. Moreover, adsorption of PPCPs onto the soil was influenced by natural organic matter (NOM) since the higher amount of NOM caused lower adsorption to the soil. Biodegradation studies of selected PPCPs by indigenous microbial community present in soil appeared that the removal rates of ACT, SA and DEET increased with time while no effect had been observed for the rest. This study suggests that the CBZ and CTMT can be considered as suitable chemical sewage indicators based on their low sorption affinity and high resistance to biodegradation.

The characteristics of activated sludge and membrane fouling were evaluated in a sponge-submerged membrane bioreactor (SSMBR) at different hydraulic retention times (HRTs) (6.67, 5.33 and 4.00h). At shorter HRT, more obvious membrane fouling was caused by exacerbated cake layer formation and aggravated pore blocking. Activated sludge possessed more extracellular polymeric substances (EPS) due to excessive growth of biomass and lower protein to polysaccharide ratio in soluble microbial products (SMP). The cake layer resistance was aggravated by increased sludge viscosity together with the accumulated EPS and biopolymer clusters (BPC) on membrane surface. However, SMP showed marginal effect on membrane fouling when SSMBRs were operated at all HRTs. The SSMBR with Gemfloc® addition at the optimum HRT of 6.67h demonstrated superior sludge characteristics such as larger floc size, less SMP in mixed liquor with higher protein/polysaccharide ratio, less SMP and BPC in cake layer, thereby further preventing membrane fouling.