Search

The paper presents a comparison of the concentration methods conventional jig, air jig, and sensor-based sorting to treat construction and demolition waste. All tests were made with concrete, brick, and gypsum particles and the tests aim to separate these materials into different size ranges, depending on the method. The equipment tested, conventional jig, air jig, and sensor-based sorting present good results to concentrate construction and demolition waste particles, with different concentrations and mass recoveries. The results show particularly good mass recoveries and particle concentration for conventional jig, especially for concrete and gypsum particles. Sensor-based sorting should preferably use concentration circuits for best results.

This paper presents a physical characterization for the recycling into new concretes of three comminuted concretes: C16/20 (“ordinary concrete”), C50/60 (“high strength concrete”), and C70/85 (“very high strength concrete”). The top size of the crushed concretes was 19.1 mm and the size range was 4.75 to 19.1 mm. The characterization was carried out with coarse aggregate liberation, to be prepared and concentrated in a gravity concentration process. The density distribution of the coarse aggregate, cement paste, and sand was carried out in different size ranges (4.75/19.1 mm, 4.75/8.0 mm, 8.0/12.5 mm, and 12.5/19.1 mm) for the three concretes studied. The form factor of the samples, as well as the porosity determination of particles in different density ranges, are presented. The obtained results indicate that the coarse aggregate liberation was more intensive for the low resistance concrete (C16/20), but a reasonable coarse aggregate recovery is possible for all concretes.

© 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/ This work aims to evaluate the use of the air jigging technique, a density-based separation technology commonly applied in mineral processing, to upgrade the quality of mixtures (density and geometric properties) that represents the typical composition of construction and demolition waste (CDW) produced in Brazil. In this sense, tests involving the variation of the main operational parameters of jigging (bed expansion rate, pulsation frequency and jigging time) were carried out aiming to find those which provided the best recycled aggregates quality after processing. Also, fines and dust emissions generation during jigging were measured in order to estimate their potential impacts on human health and environment. The results showed that the air jigging process is adequate to improve the quality of CDW by increasing the concrete concentration in the dense product. The use of high bed expansion rates showed to be of major importance to decrease the content of ceramic aggregates in the dense product, allowing obtaining products richer in concrete. Also, the measured properties of the obtained aggregates (size distribution, shape, etc) met the usual standards required for natural aggregates. Finally, material losses and dust emissions generated were negligible in comparison to the total mass processed, although special attention must be given to safety measures due the presence of inhalable particles (

The use of air jigging for performing multi-component separation in the treatment of mixed construction and demolition waste was studied. Sorting tests were carried out with mixtures of equal bulk volume of concrete and brick in which fixed quantities of unwanted materials - gypsum, wood and paper - were added. Experimental results have demonstrated the possibility to use air jigging to carry out both the removal of low-density contaminants and the concrete concentration in only one process step. In relation to the removal of contaminants only, the overall performance of jigging process can be comparable with that of commercial air classifiers and automatic sorting systems. Also, the initial content of contaminants seems does not have a significant effect on the separation extent. These results are of particular importance for recycling plants processing as they represent an alternative to optimize the use of air jigs. Further investigation is needed in order to evaluate the practical feasibility of such method.

This work deals with the separation of concrete, brick and gypsum particles from a CDW recycled aggregate mixture. Construction and Demolition Waste materials can be handled as an ore treatment problem. Efficient sorting processes of low quality CDW recycled aggregate could allow the reuse of concrete, brick and gypsum particles. The processes also improve the remaining mixed aggregates for recycling in unbound sub-base materials, by increasing their self-cementing properties and by reducing the sulfate content through the removal of gypsum. All tests were carried out in the size range between 4 and 20 mm using a laboratory air jig. The aim of the work is to concentrate a high amount of gypsum (light material) and concrete (heavy material) particles. Three working parameters are relevant for the jigging processes control such as the sorting duration, the frequency and the expansion ratio. Each of them are studied. It was found that a quadratic model of the number of jig cycles, a product of the frequency and time, accurately predict well the sorting results, if the expansion is large enough. An optimal point seems achieved at about 320 jigging cycles. Concentrates with concrete contents higher than 90% and gypsum contents significantly lower than 1% were possible to be reached and can be an alternative in aggregates for the concrete market. Indeed, gypsum reduction in concrete concentrates was about 25 times. This level of reduction could be satisfactory in sorting real demolition products. On the other hand, contents of over 70% of gypsum concentrates were obtained, increasing the reuse and recycling abilities.