Search

Since the arrival of lapped porcelain stoneware tiles on the market, several studies have been focused on the improvement of the technical characteristics of the surfaces of these products. Surface lapping induces aesthetical improvements, but can at the same time deteriorate the performance of porcelain stoneware tiles. To overcome this problem, it is possible to protect the lapped surface with commercial waterproofing materials. In this work, lapped commercial porcelain stoneware tiles with protective stain proofing agents (FILA PD15 and FILA 1239 Plus) were evaluated. The stain resistance and chemical resistance results were correlated to the morphological surface characteristics of the products with and without protection. A systematic study of the surface porosity of the tiles was carried out. Results showed that unprotected surface pores tend to fill with dirt that is hardly removable by ordinary maintenance. If the pores are protected, the dirt from foot traffic is deposited only superficially and can be removed.

The aim of this work is to evaluate the cleanability performances of lapped porcelain stoneware surfaces with and without protective treatments. The knowledge of the material cleanability is an important selection parameter in buying tiles. However, an objective basis for testing and assessing this property still is lacking. In this study, standardized and laboratory tests to evaluate the cleanability performance of lapped porcelain stoneware products have been carried out and compared. Cleanability tests were performed by applying two different soiling suspensions, optimized for tile surfaces and reproducing chemical and mechanical actions simulating the working conditions and traditional cleaning operations. Surface characteristics (microstructure, topography, roughness) were analyzed before and after cleanability tests. The results showed a good correlation between different behavior in terms of cleanability and the microscopic and topographic characteristics of lapped tile. Respect to international standardized tests specific for ceramic tiles, such as stains resistance test, the laboratory procedures to evaluate the surface cleanability are able to better show cleanability improvements of lapped tiles with protective treatments.

This research reports on the influence of particle size and distribution on the physical, mechanical and microstructural features of solid solutions (feldspathic materials) based inorganic polymer composites (IPCs). Both granite and pegmatite were ground to different degree of finess making four different granulometry with particles of 63, 80, 125 and 200 μm. The respective mixes receive 15 wt% of metakaolin and were activated with a well designed alkaline solution. Matrices obtained showed high compressive and flexural strengths in the range 101.2–131.3 MPa, and 29–35.5 MPa, respectively. It was observed that the optimum mechanical performance of these matrices can be achieved through a mix-design of different grades of granulometry. This was suggested by mechanism combining reactivity and particles packing. In fact, although it can be expected that the finess of the combination of the particles size under 63 μm might present the better reactivity, it is showing that the combination of fine, medium and coarse particles is efficient in achieving denser and tougher microstructure. Lower cumulative pore volume (17 mL g−1) of the composites based on pegmatite, value not far from that of natural stones, resulted in a higher impact resistance of 3.03 J. It was concluded that designing the feldspathic rock-based composites with high strengths appear as sustainable, low energy consumption and environmentally-friendly materials for the structural construction.

Bone grafts and bone-based materials are widely used in orthopedic surgery. However, the selection of the bone type to be used is more focused on the biological properties of bone sources than physico-chemical ones. Moreover, although biogenic sources are increasingly used for deposition of biomimetic nanostructured coatings, the influence of specific precursors used on coating&rsquo, s morphology and composition has not yet been explored. Therefore, in order to fill this gap, we provided a detailed characterization of the properties of the mineral phase of the most used bone sources for allografts, xenografts and coating deposition protocols, not currently available. To this aim, several bone apatite precursors are compared in terms of composition and morphology. Significant differences are assessed for the magnesium content between female and male human donors, and in terms of Ca/P ratio, magnesium content and carbonate substitution between human bone and different animal bone sources. Prospectively, based on these data, bone from different sources can be used to obtain bone grafts having slightly different properties, depending on the clinical need. Likewise, the suitability of coating-based biomimetic films for specific clinical musculoskeletal application may depend on the type of apatite precursor used, being differently able to tune surface morphology and nanostructuration, as shown in the proof of concepts of thin film manufacturing here presented.

The technological behavior of porcelain stoneware bodies during deposition and pressing of large slabs depends on the rheological properties of spray-dried powders and the way they affect compaction. Although the literature offers some insights into the characteristics of spray-dried powders for ceramic tiles, no data are available on bodies utilized by novel technologies for large slabs (>4 m2). In order to fill this gap, a systematic approach to properties and behavior of spray-dried powders for porcelain stoneware slabs was carried out. For this purpose, twenty industrially-manufactured spray-dried powders were characterized for intrinsic features (particle size and agglomerate size distribution; shape and moisture distribution in function of agglomerate size) and rheological properties (mass flow, static and dynamic angles of repose, poured and tap density, Hausner ratio). The effect of intrinsic characteristics on the flowability of powders was appraised, as the mutual relationships between the rheological parameters, in order to unveil the best parameters to be used in ceramic tile production. Two broad classes of spray-dried powders occur with a finer and a coarser agglomerate size distribution. Results reveal that ceramic powders are free-flowing, with rheological properties fluctuating in a rather narrow range of values, which makes hard to see significant relationships among the various methods (the only strict correlation is between mass flow rate and tap density). Flowability mainly depends on the occurrence of coarser aggregates, particularly those irregular in shape, stemming from coalescence of three or more individual agglomerates. A phenomenological description of how the spray-dried powders behave in the deposition on tape and the early stage of compaction is outlined.

Porcelain stoneware tiles are industrially processed by using high sintering temperatures and fast firing cycles that result in products characterized by an almost impervious surface layer surrounding a rather porous bulk material. Since mechanical properties are affected by porosity, the knowledge of the material stiffness is an important parameter to define the service behavior of tiles. In the present investigation, porcelain stoneware samples having different closed porosity were investigated in order to understand the influence of the porosity on the elastic constants of the materials. Based on the quantitative XRD phase composition, elastic constants have been calculated via Voigt-Reuss-Hill averaging, and the influence of porosity has been taken into account via power-law and exponential relations. It is shown that the effective elastic constants predicted by exponential and power-law relations are in agreement with experimental values. It may be concluded that for this class of materials, in the porosity range below 14–16%, both exponential and power-law relations are helpful tools to design tiles with controlled microstructure and tailored mechanical properties.

The response to thermal variations is the primary cause of marble deterioration in ancient and modern buildings. In this study, the thermal behavior of Carrara marble after consolidation by an innovative hydroxyapatite-based treatment was investigated in comparison with ammonium oxalate and ethyl silicate. Samples were subjected to heating-cooling cycles up to 80 °C. All the consolidating treatments were found to be fairly compatible, as in no case the residual strain after the thermal cycles was found to increase compared to the unweathered untreated marble. Anyway, the hydroxyapatite-treatment has the advantage of causing the highest increase in marble cohesion and the lowest residual strain, besides being more chromatically compatible and durable than the alternative commercial consolidants. Keywords: Hydroxyapatite, Calcium oxalate, Thermal expansion coefficient, Residual strain, Dilatometry

Geopolymers are hydrated aluminosilicates with excellent binding properties. Geopolymers appeal to the construction sector as a more sustainable alternative to traditional cements, but their exploitation is limited by a poor understanding of the linkage between chemical composition and macroscopic properties. Molecular simulations can help clarify this linkage, but existing models based on amorphous or crystalline aluminosilicate structures provide only a partial explanation of experimental data on the nanoscale. This paper presents a new model for the molecular structure of geopolymers, in particular for nanoscale interfacial zones between crystalline and amorphous nanodomains, which are crucial for the overall mechanical properties of the material. For a range of Si–Al molar ratios and water contents, the proposed structures are analyzed in terms of skeletal density, ring structure, pore structure, bond-angle distribution, bond length distribution, X-ray diffraction, X-ray pair distribution function, elastic moduli, and large-strain mechanics. Results are compared with experimental data and with other simulation results for amorphous and crystalline molecular models, showing that the newly proposed structures better capture important structural features with an impact on mechanical properties. This offers a new starting point for the multiscale modeling of geopolymers.

Air- and formulated lime mortars with pulverized brick waste were synthesized with addition of two organic waste-based additives: spent cooking oil and albumen. The addition of spent oil in the mortar induced significant hydrophobic effects, but decreased permeability values and setting kinetics. Parallel additions of oil and albumen in lime mortars significantly increased their hydrophobicity and superficial durability without retarding their setting time thanks to role of fatty acids and unfolded proteins under alkaline conditions. The parallel valorization showed high potentials in synthesis of restorative mortars design with low environmental impact and high respect to the feature of historic mortars. (C) 2018 Elsevier Ltd. All rights reserved.

This review presents “a state of the art” report on sustainability in construction materials. The authors propose different solutions to make the concrete industry more environmentally friendly in order to reduce greenhouse gases emissions and consumption of non-renewable resources. Part 1—the present paper—focuses on the use of binders alternative to Portland cement, including sulfoaluminate cements, alkali-activated materials, and geopolymers. Part 2 will be dedicated to traditional Portland-free binders and waste management and recycling in mortar and concrete production.

The suitability of new lime mortars for restorative rendering applications was investigated. Air-, formulated- and hydraulic-lime mortars were synthesized with inclusion of two different types of spent sunflower cooking oils and, when necessary, brick waste powder as pozzolanic addition. The results of spent cooking oils addition in the mortars exhibited promising hydrophobic effects, such as sorptivity reduction up to 60 times and improvement of superficial durability. Addition of high-oleic acid cooking oil in 13 wt% in the formulated and hydraulic lime mortars significantly increased their hydrophobicity without worsening their mechanical strengths. All the investigated mortars exhibited appropriate indexes as restorative materials.

Glass with different chemical compositions, deriving from separate collection, has been used as fine aggregate to formulate cementitious mortars, substituting natural sand. Glass coming from cathode-ray tube monitors, fluorescent lamps, and crystal glass (from production of home decor items) along with glass deriving from soda-lime glass containers, which has been taken as a reference, have been investigated. Glass solubility has been determined in alkaline environment similar to the one inside the cementitious composite. Alkali silica reaction has been tested on glass modified cement mortar in different accelerated conditions. Mortar samples containing glass with chemical composition different with respect to soda-lime glass are subjected to alkali silica reaction. This behaviour is largely dependent on the ratio among modifier and stabilizer oxides in the glass. The same ratio affects glass solubility and consequently composition of expanding gels when alkali silica reactions take place.

This paper aims at evaluating how the FRP/brick debonding force is influenced by brick mechanical properties (compressive, tensile and flexural strength) and physical-microstructural properties (surface roughness, porosity, pore size distribution, rate of water capillary suction). The depth of epoxy resin penetration into bricks and the thickness of brick layer detached at the end of bond test were also determined, in order to investigate the role of resin penetration into the brick on the FRP performance. All the tests were carried out on different brick surfaces (namely “bed” and “face”), to account for possible brick anisotropy. The results of the study point out that brick mechanical properties alone are not sufficient to accurately predict the maximum debonding force, but a better estimation can be achieved taking into account also brick surface roughness and resin penetration depth. If brick anisotropy is not considered, in some cases a remarkable overestimation of the maximum debonding force may be found.

Alkali-activation of brick waste has recently been proposed as a sustainable route to develop pastes/mortars with tailored mechanical properties and pore system. In this study, the suitability of using pastes from brick waste alkali-activation for repointing existing masonries (i.e., filling the most external part of mortar joints, lost due to deterioration processes) was investigated. Five different formulations (having SiO 2 /Al 2 O 3 molar ratio ranging from 1.4 to 0.4) and two different curing temperatures (room temperature and 50 °C) were investigated. Open porosity and efflorescence formation were found to decrease for decreasing SiO 2 /Al 2 O 3 ratio. Curing at high temperature generally favored geopolymerization and reduced efflorescence formation. Pastes with SiO 2 /Al 2 O 3 =0.8 and 0.9 exhibited open porosity and water vapor permeability fairly similar to those of historic lime-based mortars, thus proving to be potentially compatible with them. Further optimization of the mix design seems however necessary to reduce the formation of efflorescence.