Search

[Display omitted] • Novel green chromatographic method for the simultaneous determination of 5-fluorouracil and cisplatin. • Evaluation of the greenness profile using NEMI, GAPI, Eco-scale and AGREE tools. • Application of a newly developed HPLC method to evaluate the drug release of co-loaded 5-fluorouracil and cisplatin films. The combination of 5-fluorouracil (5-FU) and cisplatin (Cis) has been used for the treatment of many cancers. The combination demonstrates synergy and improved clinical outcomes encouraging developing a formulation with both drugs. An analytical procedure is essential for formulation studies; however, no method has been reported for the concurrent determination and quantification of both 5-FU and Cis to date. A novel, simple, accurate, and precise HPLC method was developed using a C 18 column (250 mm × 4.6 mm, 5 µm) and mobile phase composed of 0.5 mM sodium dodecyl sulfate: methanol (98:2, v/v), adjusted to pH 2.5 with phosphoric acid. A flow rate of 0.5 mL/min was applied and a photodiode array was utilized for detection and the retention times were 9.89 min (265 nm) for 5-FU and 5.36 min (210 nm) for Cis. Validation procedures were performed, and the method was found to be linear at ranges of 0.9–60.0 µg/mL for 5-FU and 6.0–60.0 µg/mL for Cis. The limits of detection (LOD) and quantitation (LOQ) were 0.10 and 0.25 µg/mL for 5-FU and 2.00 and 4.00 µg/mL for Cis, respectively. Other parameters such as precision, selectivity, robustness, and stability results were within acceptable limits. The method was applied to a model co-eluting film and its release profile was studied. Additionally, the method's greenness was evaluated by four assessment tools namely the national environmental method index (NEMI), analytical eco scale assessment (ESA), green analytical procedure index (GAPI), and Analytical GREEnness Metric Approach and Software (AGREE). The results demonstrated compliance with green analytical chemistry (GAC) practices. This research acts as a step towards further investigation of drug stability under different stress conditions and quantification of the intact drugs in presence of their degradation products. [ABSTRACT FROM AUTHOR]

[Display omitted] • Drug-in-adhesive patches containing 5-fluorouracil for the treatment of skin cancer. • Pressure-sensitive adhesives using Eudragit® E and plasticizers for topical application. • Solubility parameters and thermal analysis for polymer-plasticizer miscibility evaluation. Topical patches containing 5-fluorouracil (5-FU) are a feasible alternative to overcome the shortcomings of commercial cream for the treatment of non-melanoma skin cancer (NMSC). Plasticizers are a critical component of drug-in-adhesive (DIA) patches as they can significantly affect the mechanical, adhesive and drug release characteristics of the patches. Eudragit® E (EuE) is a methacrylate-based cationic copolymer capable of producing flexible and adhesive films for topical application. In this study, the effect of plasticizers on the mechanical, adhesive and 5-FU release characteristics of EuE-based patches was comprehensively evaluated. While the elongation at break (%) and adhesion of the films were significantly increased with increasing triacetin, dibutyl sebacate (DBS) and triethyl citrate (TEC) concentrations, the tensile strength showed an inverse relationship. EuE plasticized with 40% triacetin, 30% DBS or 40% w/w TEC produced elastic and adhesive films most suitable for topical application. In vitro release studies of the 5-FU-loaded patches demonstrated an initial burst release pattern during the first 10 min followed by a slow release over 120 min. In summary, this study provides important information on effect of plasticizers for preparation of EuE-based patches with desired mechanical, adhesive and release characteristics of 5-FU towards their potential application in the treatment of NMSC. [ABSTRACT FROM AUTHOR]