Search

Converter transformers use oil-pressboard as their main dielectric medium and are operated mainly in AC-DC combined electric field. For oil-pressboard insulation, the electric field under DC voltage shows distinctive characteristics from that in AC electric field. Compared to conventional AC power transformers, the electric filed distribution in the converter transformers is much more complicated and remains a big challenge for optimization of insulation design. Existing simulation research in this field falls short of experimental verification and shows limitations in the insulation design of the converter transformers. This paper attempts to fill the gap by measuring the dynamic process and distribution of electric filed in oil-pressboard insulation under the combined field so as to provide reference for insulation design. With the established Kerr-effect electric field measurement platform, the present paper recorded the dynamic process and distribution of AC and DC electric fields at different AC/DC ratios for the double-layer overlapping oil-pressboard insulation model. The research results indicate that 1) the AC electric field distribution in oil is homogeneous and symmetric. The field strengths form linear relation with the amplitudes of applied voltages; 2) the DC electric field distribution in oil is heterogeneous and asymmetric. Under the application of positive DC voltage, the field strength around the upper electrode is much smaller than that of the lower one. The DC electric field strength shows no linear growth with the increase of the applied voltages; 3) the accumulation of interface charges forms the major cause resulting in the asymmetric distribution of the DC electric field at different positions of the insulation. The research results imply that although RC model is recognized as effective simulation method for insulation design of conventional transformers, it shows its limitations and should be enriched and adjusted according to the electric field distribution under AC-DC combined voltage and taking into full consideration of the accumulation of interface charges. [ABSTRACT FROM PUBLISHER]

The degradation of insulation would be accelerated by the partial discharge (PD) incurred by an internal air-gap defect in oil-pressboard insulation. At different bridge rectifier locations in the converter transformer, the oil-pressboard insulation typically endures various ratios of combined ac and positive dc voltages. Therefore, the dielectric status of the converter transformer is closely correlated to the ratios of ac to dc voltages. It is practically significant to conduct the study of the correlation between discharge characteristics and ac-dc ratios. At the same time, it enhances the diagnosis of faults in converter transformers. According to the actual internal operation conditions of converter transformers, the study established a test platform. Furthermore, the conventional pulse current method was adopted to compare the discharge characteristics at the initiation and close-to-breakdown stages. Under these ratios, test results display distinctive PD dynamics. The PD of the air gap generates surface charges. These charges, in turn, establish an inverse electric field. As a result, the proportion of dc in the ac-dc combined voltage increases, and total initial voltage and total breakdown voltage increase continuously, but the recurrence rate of discharge pulse and discharge magnitude decrease at the initiation and close-to-breakdown stages. As the positive dc proportion increases, the discharge recurrence rate in the negative half cycle gradually exceeds that in the positive one. These research findings provide useful criteria for the fault diagnosis of converter transformers. [ABSTRACT FROM PUBLISHER]

Converter transformers use oil-pressboard as its main dielectric medium and are operated mainly in AC-DC composite electric field. Creepage discharge is one of the common defects for oil-pressboard insulation, especially in converter transformers. Oil-pressboard insulation shows distinctive flashover behaviors and surface electric strengths in AC-DC composite electric field from that in pure AC or DC electric field. Compared to conventional power transformers, there remain bigger challenges to realize insulation assessment and fault diagnosis for the converter transformers. Adequate knowledge of the phenomenon and characteristics of oil-pressboard insulation creepage discharge is critical for fault diagnosis of converter transformers. This paper attempts to fill the existing research gap by studying the dynamic process and phenomenon of creepage discharge in the composite field so as to provide criteria for insulation diagnosis and assessment. With the established experimental platform, the present paper observed the phenomenon of oil-pressboard insulation creepage discharge from its initiation till final flashover under composite AC-DC voltages, identified the trends of partial discharge and dissolved gas throughout the entire process, and summarized accordingly the criteria for insulation diagnosis and assessment. Results indicate that 1) for creepage discharge of oil-pressboard insulation under AC-DC superimposed voltages, abrupt changes were observed in terms of discharge repetition rate and magnitude. Discharge phases kept enlarging during the whole discharge evolution process; 2) based on the observed discharge characteristics, the evolution process of creepage discharge could be classified into three stages which imply three severity levels of the discharge; 3) compared to that in AC electric field, the creepage discharge in AC-DC composite field witnessed much less amount of and different composition of dissolved gas in oil. More C₂H₆ and C₂H₂ were observed in the AC-DC composite electric field whereas CH4 and C₂H₂ dominated the AC electric field. The research results indicate that as much as both PD-identification and DGA methods are recognized as effective means of fault diagnosis for converter transformers, the referential assessment criteria should be enriched and adjusted for diagnosis of creep discharge under AC-DC composite voltages, taking into full consideration of the distinctive characteristics of both discharge and gases dissolved in oil. [ABSTRACT FROM PUBLISHER]