Search

The effects of low-concentration monorhamnolipid (monoRL) on the adsorption of Pseudomonas aeruginosa ATCC 9027 grown on glucose or hexadecane to glass beads with hydrophobic or hydrophilic surfaces was investigated using batch adsorption experiments. Results showed that adsorption isotherms of the cells on both types of glass beads fitted the Freundlich equation better than the Langmuir equation. The K f of the Freundlich equation for adsorption of hexadecane-grown cell to glass beads with hydrophobic surface was remarkably higher than that for adsorption of hexadecane-grown cell to glass beads with hydrophilic surface, or glucose-grown cell to glass beads with either hydrophilic or hydrophobic surface. Furthermore, it decreased with the increasing monoRL concentration. For both groups of cells, the zeta potential was close to each other and stable with the increase of monoRL concentration. The surface hydrophobicity of hexadecane-grown cells, however, was significantly higher than that of the glucose-grown cells and it decreased with the increase of monoRL concentration. The results indicate the importance of hydrophobic interaction on adsorption of bacterial cells to surfaces and monoRL plays a role in reducing the bacterial adsorption by affecting cell surface hydrophobicity. [ABSTRACT FROM AUTHOR]

In this article, a rhamnolipid-functionalized graphene oxide (RL-GO) hybrid was prepared by one-step ultrasonication and adsorptive removal of methylene blue (MB) from both artificial and real wastewater by the RL-GO was investigated. The Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Fourier transform infrared spectrum (FT-IR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET) area and Zeta potential analysis were used to characterize the adsorbent. The results showed that RL-GO had abundant functional groups and a mesopores feature. MB adsorption by the RL-GO increased with increase in adsorbent dose, pH, temperature and initial MB concentration, while it was insensitive to ionic strength variation. The adsorption kinetics fitted well to the pseudo-second-order model with correlation coefficients greater than 0.999. The Intra-particle diffusion and Boyd's film-diffusion models showed that the rate-controlled step was dominated by film-diffusion in the beginning and then followed by intra-particle diffusion. The adsorption isotherm was fitted by adsorption models with the suitability in order of BET > Freundlich > Langmuir > Temkin, based on comparison between correlation coefficients. Thermodynamic analysis of equilibriums suggested that the adsorption MB on RL-GO was spontaneous and endothermic. The adsorption mechanism was also proposed to be electrostatic attraction, π–π interaction and hydrogen bond. In addition, the real wastewater experiment, the regeneration study and the comparative cost analysis showed that the RL-GO composites could be a cost-effective and promising sorbent for MB wastewater treatment owing to its high efficiency and excellent reusability. [ABSTRACT FROM AUTHOR]

Agricultural plastic films and triazole fungicides are widely used in agricultural production process. Exposure to natural environment, agricultural plastic films will degrade into micron plastic particles, which will adsorb pesticide molecules and may affect their toxicity, biological activity and persistence. The long-term coexistence of microplastics (MPs) and triazole fungicides will bring potential harms to the agricultural ecological environment. Therefore, two kinds of triazole fungicides flusilazole (FLU) and epoxiconazole (EPO) were selected as cases and the adsorption behaviors of them on polystyrene and polyethylene were investigated. A series of factors which could affect the adsorption behavior were evaluated. Specifically, the particle size of MPs could affect its adsorption capacity, and the smaller the particle size, the stronger the adsorption capacity. Moreover, with the increase of pH value from 6.0 to 9.0, the adsorption capacity of MPs to target compounds gradually increased. The effect of ionic strength was evaluated by NaCl, and 0.05% of NaCl was beneficial to the adsorption process, while the continuous increase of NaCl concentration inhibited the adsorption. Oxalic acid and humic acid decreased the adsorption capacity of flusilazole on PE by 15.99–32.00% and PS by 35.02–48.67%, respectively. In addition, compared with the single pesticide system, the adsorption capacity of MPs for flusilazole and epoxiconazole in the binary pesticides system decreased by 36.13–37.93% and 44.36–51.35%, respectively, indicating that competitive adsorption occurred between the two pesticides. Meanwhile, the adsorption process was evaluated by adsorption kinetics and adsorption isotherms and were consistent with pseudo-second-order kinetic model and Freundlich isotherm model, respectively. Finally, several characterization analyses were conducted to investigated the adsorption mechanism, and hydrogen, halogen bonding and hydrophobic interaction proved to play an important role. The study on the adsorption behavior and mechanism of pesticide on MPs was the basis of assessing the risk of joint exposure. [Display omitted] • The adsorption capacity of the same pesticide on PE was higher than that on PS. • The adsorption capacity of FLU was higher than EPO on the same MPs. • In the binary pesticide system, competitive adsorption occurred between pesticides. • Adsorption mechanisms include hydrogen, halogen bonds, and hydrophobic interactions. [ABSTRACT FROM AUTHOR]

Abstract: Using two spirocyclic core building units, microporous polymeric spheres SPOP-5 and SPOP-6 have been successfully prepared through a surfactant-free Suzuki coupling polymerization in a single-phase, which is different from the commonly employed heterogeneous polymerization technique. Especially, for SPOP-6, the SEM image shows that the polymer consists of relatively uniform monodisperse solid microspheres with particle sizes about 500 nm in diameter. The mechanism of microsphere formation is believed to occur by a two-step process involving particle nucleation and subsequent growth. The Brunauer–Emmett–Teller (BET) specific surface area for these polymers ranges from 705 to 744 m2 g−1. Based on the gas (H2 or CO2) physisorption isotherms, an increase in the gas loading capacity with increasing specific surface area is observed. Especially, hydrogen adsorption isotherms show that the adsorption capacity of SPOP-6 for hydrogen is 1.62 wt% at 1.0 bar and 77 K, which can be competitive with, even higher than lots of porous polymers with higher BET specific surface area under the same conditions. [Copyright &y& Elsevier]