Search

A biocompatible and uniquely defined hydroxyapatite (HAP) adsorption membrane with a sandwich structure was developed for the removal of organic micropollutants for the first time. Both the adsorption and membrane technique were used for the removal of organic micropollutants. The hydrophilicity and hydrophobicity of the HAP adsorbent and membrane were tunable by controlling the surface structure of HAP. The adsorption of organic micropollutants on the HAP adsorbent was studied in batch experiments. The adsorption process was fit with the Freundlich model, while the adsorption kinetics followed the pseudo-second-order model. The HAP membrane could remove organic micropollutants effectively by dynamic adsorption in both aqueous and ethanol solutions. The removal efficiencies of organic micropollutants depended on the solution composition, membrane thickness and hydrophilicity, flow rate, and the initial concentration of organic micropollutants. The adsorption capacities of the HAP membrane with a sandwich structure (membrane thickness was 0.3 mm) were 6700, 6510, 6310, 5960, 5490, 5230, 4980 and 4360 L m −2 for 1-naphthyl amine, 2-naphthol, bisphenol S, propranolol hydrochloride, metolachlor, ethinyl oestradiol, 2,4-dichlorophenol and bisphenol A, respectively, when the initial concentration was 3.0 mg L −1 . The biocompatible HAP adsorption membrane can be easily regenerated by methanol and was thus demonstrated to be a novel concept for the removal of organic micropollutants from both aqueous and organic solutions. [ABSTRACT FROM AUTHOR]

A novelly-defined adsorption membrane for rapid removal of fluoride from drinking water was prepared. Both zirconium metal-organic frameworks (Zr-MOFs) adsorbent and membrane with large specific surface area of 740.28 m 2 /g were used for fluoride removal for the first time. For adsorption technique, fluoride adsorption on Zr-MOFs was studied on a batch mode. The adsorption data could be well described by Langmuir isotherm model while the adsorption kinetic followed pseudo-second-order model. The maximum of adsorption capacity was 102.40 mg/g at pH 7.0 when the initial fluoride concentration was 200 mg/L. The FT-IR and XPS analyses of Zr-MOFs revealed that both surface hydroxyl groups and Zr(IV) active sites played important roles in fluoride adsorption process. The as-prepared Zr-MOFs adsorbent was suitable for practical treatment of drinking water and regeneration by sodium hydroxide solution (3 wt%). For membrane experiments, Zr-MOFs membrane supported on Alumina substrate could remove fluoride efficiently through dynamic filtration. The fluoride removal capability of Zr-MOFs membrane depended on flow rate and initial concentration of fluoride. The fluoride removal abilities of Zr-MOFs membrane with 20 μm thickness could reach 5510, 5173, and 4664 L/m 2 when fluoride concentrations were 5, 8 and 10 mg/L, respectively. This study indicated that Zr-MOFs membrane could be developed into a very viable technology for highly effective removal of fluoride from drinking water. [ABSTRACT FROM AUTHOR]

• Recent developments in fluoride removal from water by adsorption are reviewed. • Four technical strategies are proposed for designing of adsorbents. • Transfering the adsorption process to industrial scale is urgently needed. • Fluoride adsorption and desorption in field condition need further investigation. Fluoride contamination in water environment due to natural and artificial activities has been recognized as one of the major problems worldwide. Developing effective and robust technologies for excess fluoride removal from water environment becomes highly important. Among the commonly used treatment technologies applied for fluoride removal, adsorption technique has been explored widely and offers a highly efficient simple and low-cost process for fluoride removal from water. This review reports the recent developments in fluoride removal from water environment by adsorption methods. Studies on fluoride removal from aqueous solutions using various carbon materials are reviewed. It is evident that various adsorbents with high fluoride removal capacity have been developed, however, there is still an urgent need to transfer the removal process to industrial scale. Regeneration studies need to be performed in more extent to recover the adsorbent in field conditions, enhancing the economic feasibility of the process. Based on the review, four technical strategies of adsorption method including nano-surface effect, structural memory effect, anti-competitive adsorption and ionic sieve effect can be proposed. The design of adsorbents through these four strategies can greatly improve the removal efficiency of fluoride in water and provide guidance for the development of new efficient methods for fluoride removal in the future. [ABSTRACT FROM AUTHOR]

Increasing exposure to arsenic (As) contaminated ground water has become a global health hazard to humanity. Suitable adsorbent for As removal from water, especially for As(III) than As(V), is an urgent but still a challenging task. In this study, waste orange peel (OP) was modified with magnetic nanoparticles followed by calcination as a novel adsorbent and investigated for instantaneous oxidation and adsorption of As(III) from aqueous solutions. The batch adsorption experimental results showed that calcined magnetic orange peel composites (CMOPC) exhibited superior As(III) adsorption capacity (10.3 mg/g) as compared to similar cost effective adsorbents due to its high surface area, large pore size and greater numbers of active sites on its surface. The adsorption equilibrium data obeyed Langmuir model, and kinetic data was well described by the pseudo-second-order model. The adsorption mechanisms for As(III) might be involved ligand exchange of the hydroxyl in CMOPC to form Fe-O-As(III), and partial As(III) oxidation to As(V) followed by instantaneous adsorption on surface of CMOPC. The developed adsorbent has also demonstrated good anti-interference ability to co-existing ions, admirable regeneration ability and pronounced capacity in treating simulated real As(III) contaminated water. This study revealed that waste orange peel, after simple treatment could be used as a potential adsorbent for As(III) from aqueous solutions. [ABSTRACT FROM AUTHOR]

Removing heavy metals from aqueous solutions has drawn more and more attentions these years because of their serious global health challenge to human society. To develop an adsorbent with low-cost and high-efficiency for removal of heavy metals (HMs), β-cyclodextrin (β-CD) polymers crosslinked with rigid aromatic groups were prepared and used for lead (Pb), copper (Cu) and cadmium (Cd) removal for the first time. The negatively charged β-CD polymers with large BET surface area were suitable to be used in HMs adsorption. The adsorption process completed in 5 min was well fit by Freundlich isotherm model and pseudo-second-order model. The intraparticle diffusion model was also appropriate to describe the adsorption of Pb, Cu and Cd on β-CD polymer. The maximum of adsorption capacities at 25 °C for Pb, Cu and Cd were 196.42, 164.43 and 136.43 mg/g when the initial concentration was 200 mg/L. The HMs adsorption process on the surface of β-CD polymer was an endothermic and spontaneous process. Both of the electrostatic interaction and distribution of Pb, Cu and Cd species influenced the adsorption process at different pH values. The order of removal efficiencies in multi-component adsorption for the three metal ions were Pb > Cu > Cd. The adsorption mechanisms were H + ions on hydroxyl groups exchanged with heavy metal ions and electrostatic interactions. This study indicated that β-CD polymers could be developed into effective adsorbents for rapid removal of heavy metals. [ABSTRACT FROM AUTHOR]

• UiO-66-NH 2 can effectively remove norfloxacin in water. • UiO-66-NH 2 can remove norfloxacin well in the neutral pH range. • The NH 2 and Zr O bonds play important role for norfloxacin removal. • Various adsorption mechanisms for norfloxacin removal are explored. Antibiotics abuse has been a significant threat to the environment and human health. In this study, we successfully synthesized highly stable amino-functionalized Zr-based metal–organic frameworks (UiO-66-NH 2) and studied the adsorption behaviors of norfloxacin (NOR) in water. The adsorption capacities of UiO-66-NH 2 reached a maximum of 222.5 mg/g for NOR, which were considerably higher than that of most reported adsorbents. Moreover, the equilibrium time (6 h) was less than that of several previously reported adsorbents. Ionic-strength-influenced experiments showed that NaCl and CaCl 2 aqueous solutions could improve the removal efficiency of NOR. The presence of humic acid could barely affect the adsorption amount. At a concentration of 10 mg/L, the highest partition coefficient of 20.9 mg/g/µM was obtained, and the removal rate of NOR was as high as 91.6%, implying that UiO-66-NH 2 offered considerable adsorption performance at a low concentration of NOR. In addition, UiO-66-NH 2 exhibited good regeneration efficiency, thus offering the possibility to remove norfloxacin from sewage. Finally, several credible adsorption mechanisms were proposed. The results will aid us to comprehend the surface interaction between organic micropollutants and UiO-66-NH 2 and prefigure the potential of UiO-66-NH 2 as a novel adsorbent for the removal of NOR. [ABSTRACT FROM AUTHOR]