Search

This work aimed, to evaluate the structural behavior of Oxisols based on the least limiting water range (LLWR) and establish relations with corn crop. The experiment was carried out in a randomized block design with five treatments and four replications. Soil samples collected at the layer of 0-0.20 m depth in a Haplustox (LVd) and an Eutrustox (LVef) were used. The compaction treatments consisted of T0= no additional compaction; T1 and T2= two and four passes with a 4 t tractor, respectively; T3 and T4 = two and four passes with a 10 t tractor, respectively. The range of LLWR variation in the LVd was the lowest one and varied from 0.01 to 0.04 m3 m-3, whereas in the LVef varied from 0.03 to 0.13 m3 m-3 for the critical soil penetration resistance (PRc) of 2 MPa. It was observed that critical bulk density (BDc) values were 1.76 and 1.40 Mg m-3 in the LVd and the LVef, respectively. The highest frequency of bulk density (BC = BDc) occurred from the T1 to T4 (LVd) and from the T2 to T4, however, a reduction in corn yield was not observed. The determination of the LLWR was efficient and complementary for identifying more favorable or more impeditive conditions to compaction in the LVef for the corn crop development in relation to the LVd. [ABSTRACT FROM AUTHOR]

Variations in sinkage and cone index are of crucial importance when planning fieldwork, and for determining the trafficability of farm machinery. Many studies have highlighted the link between higher values of these parameters and dramatic decreases in crop yield. Variations in the dry bulk density and cone index of clayey soil in Southern Spain were measured following each of five successive passes over the same land with the three types of tractor most widely used in the area (tracked, two-wheel drive and four-wheel drive). In addition, sinkage (rut depth) of the running gear was measured using a laser microrelief profile meter. This device, which integrates three sensors, was specifically designed for these experiments, as was an electrical penetrometer to determine the cone index, and both instruments proved reliable and accurate in the field. The main goal of this study was to design, manufacture and test these new devices. The first pass caused most soil alteration when compared to successive passes for all types of tractor tested and soil conditions prevailing during the tests. (Heavier) four-wheel drive tractors were found to cause greater soil damage (sinkage, cone index and dry bulk density) than two-wheel drive and track tractors. There was no statistically significant difference between the two latter types. The greatest alterations were recorded in the top 10 cm of the soil. The results show that soil compaction should be avoided as much as possible. This can be achieved by ensuring that tractors always travel along the same tracks, especially in the wet season. At present these aspects are not considered by farmers in this area. [ABSTRACT FROM AUTHOR]

Abstract: Farmers may desire a high cone index soil for tractive purposes or a low cone index (CI) soil for root penetration and seedling emergence. The function of any agricultural tractor is to provide mobility for itself and to power an implement. The aim of this paper was to (a) assess the impact of two tractors with different tyre sizes and axle loads on motion resistance (MR) and on the CI for three different soil mechanic conditions and (b) determine the existing relationships between MR and ground pressure parameters and tyre sinkage. Traffic was simulated with one pass on clay soil for a front-wheel assist tractor (FWA, load=77.7kN) and a four-wheel drive tractor (4WD, load=98.01kN) on three soil conditions: direct sowing systems, ploughed and seedbed. The outlined hypotheses were as follows: (1) there is a direct relationship between the subsoil compaction and the MR force of the FWA and 4WD tractors, and (2) the power loss produced by the MR depends on the soil mechanics. The experiment was conducted in the eastern section of the Rolling Pampa region of Argentina at 34°36′S, 58°40′W. MR, rut depth (RD) and CI were measured. The MR mean values of the 4WD were 9.30, 6.59 and 2.31kN for ploughed, seedbed and direct sowing soil, respectively, whereas the values for the FWA were 10.41, 7.91 and 4.67kN, respectively. For the three soil conditions, no significant differences were found in the RD between the 4WD and FWA. For the topsoil level (0–150mm), one FWA pass caused mean values in the CI of 2150, 1835 and 1780kPa for direct sowing, seedbed and ploughed soil, respectively, whereas for 4WD the values were 1890, 1640 and 1587kPa, respectively. For the subsoil (150–600mm), 4WD caused higher CI values than the FWA. The CI mean values of the 4WD were 2477, 2240 and 1890kPa for direct sowing, seedbed and ploughed soil, respectively, whereas the values for the FWA were 2240, 1870 and 1770kPa, respectively. For the different soil conditions, the subsoil compaction increased as the total axle load increased, independently from the ground pressure. Moreover, for both tractors, a greater MR force was observed in the soil with the lowest bearing capacity. The smallest power loss ratio due to MR and engine power was found with the 4WD. [Copyright &y& Elsevier]