Search

Cold-worked Inconel 718 alloy has successful applications in turbine engines due to its elevated strength. Otherwise, cold working will bring about the undesired ductility degradation accompanied with strength improving. Meanwhile, the susceptibility to δ precipitation is increased with modified morphology. To address these issues, this work aims expressing the effect of cold-rolling on hot ductility and the role of δ phase regarding differential morphologies in tensile behavior of Inconel 718 alloy at 650 °C. The results revealed that the ductility degradation can be attributed to the interactions of necking, microstructure instability and oxidation process tailored by cold-rolling. Nevertheless, appropriate cold-rolling is proved to enhance the resistance to crack propagation. The needlelike δ phase in strain-free structure tightly hindered the migration of horizontal GBs to enhance the strength but promote the intergranular brittle cracking, resulting in the degradation of ductility. In contrast, the δ phase with modified granular morphology in cold-rolled structures showed good deformation compatibility with horizontal GBs, playing a positive role in delaying necking occurrence and impeding crack propagation. In summary, the granular δ precipitation endowed cold-rolled Inconel 718 alloy with a superior combination of strength and ductility at 650 °C. [ABSTRACT FROM AUTHOR]

Precipitation evolution and strengthening effect of Al-15wt%Mg2Si-5wt%Cu alloy were studied by characterizing the change of morphology and tensile properties after ageing at 200 °C for various times. At the under-ageing condition (ageing for 0.5 h), metastable θ″, θ′, fine dots and σ phases are formed. After ageing for 1 h (peak-ageing condition), θ″ and θ′ are dominant phases, and the high number density of precipitates produces a significant improvement of the hardness (173 Hv) and ultimate tensile strength (356 MPa). As ageing time is prolonged (ageing for 24 h), plenty of σ phases are formed at the expense of θ"/θ′ phases and act as the main strengthening precipitates. The over-aged microstructure consequently causes a decrease in the hardness (134 Hv) and ultimate tensile strength (311 MPa) of the alloy. [ABSTRACT FROM AUTHOR]

Microalloying of an Al-15%Mg 2 Si alloy (wt%) with 1%Cu produced an enhanced age-hardening response, increasing peak hardness and ultimate tensile strength due to a modified precipitation process. The solid solubility of Cu in Al-15%Mg 2 Si alloy effectively promotes the formation of the high number density of Guinier-Preston-Bagaryasky (GPB) zones combined with S precipitates. It suppresses β′ and β″ formation during ageing at 200 °C. Consequently, Al-15%Mg 2 Si-1%Cu alloy with the high density of GPB zones and S phase exhibited high peak hardness (121 HVN) and ultimate tensile strength (284 MPa), 42.4% and 49.5% higher than that of the Al-15%Mg 2 Si alloy, respectively. • The addition of 1% Cu in Al-15%Mg 2 Si alloy has a significant influence on precipitation during ageing at 200 °C. • Cu addition promotes the formation of GPB zones and S phase, instead of β′ and β″ precipitates. • The high number density of GPB zones and S phase produces an enhanced age-hardening response. [ABSTRACT FROM AUTHOR]

The microstructure control of multiphase Ni 3 Al-based intermetallic alloy by traditional heat treatment is still limited, especially size and volume fraction of interdendritic β phase cannot be effectively reduced, due to the limitation of interdendritic β phase dissolution temperature close to the melting point of the alloy. In present work, the temperature gradient and solidification rate of the alloy under different laser remelting parameters were calculated by the Rosenthal equation. Afterward, the as-cast multiphase Ni 3 Al-based intermetallic alloy (19.4 vol% of interdendritic β phase) was remelted under different laser parameters of 3000–4500 W laser power and 5–20 mm/s laser scanning rate. And the effects of different laser remelting parameters on the microstructure, room temperature, and 980 °C high-temperature tensile properties of multiphase Ni 3 Al-based intermetallic alloy were studied. The results show that laser remelting treatment with the appropriate parameters (4000 W laser power and 10 mm/s laser scanning rate) can effectively reduce the size and volume fraction of interdendritic β phase and the morphology and size of γ′ phase in the γ′+γ dendrite, and significantly refine the microstructure of alloy, thus effectively improving the room temperature and 980 °C tensile properties of multiphase Ni 3 Al-based intermetallic alloy. Under the optimum laser remelting parameters of 4000 W-10 mm/s, the tensile strength at room temperature and 980 °C of the corresponding laser remelting alloy can reach 1215 MPa and 280 MPa, respectively, and the elongations after fracture of the corresponding alloy are 14.09% and 6.41%, respectively. [ABSTRACT FROM AUTHOR]