Search

In multi-beamlet negative ion accelerators for neutral beam injectors, the transverse magnetic field necessary for suppressing the co-extracted electrons induces a deflection of the negative ion beamlets that must be corrected. For the design, particle-tracing simulation codes are used to compute ion trajectories and optical properties of the beamlets in the acceleration stage. In these codes, uniform boundary conditions are normally assumed for the ion current density distribution at the surface (called meniscus), where negative ions are extracted from the plasma and form beamlets, which are accelerated across the apertures of the accelerator grids. Recently, experimental campaigns dedicated to the accurate measurement of the beamlet deflection in the acceleration phase revealed higher deflection than foreseen by simulations. In this work, we demonstrate that an agreement with the experimental data can be obtained by incorporating in the numerical simulations a non-radially symmetric distribution of the ion current density extracted across the meniscus surface. In the first part, the asymmetry of the ion current density at the meniscus is studied in an empirical way, by analysing and fitting the experimental results obtained with different operating parameters. In the second part, we show that the ion current asymmetry estimated by this procedure is well consistent with the flow pattern of H− ions calculated in the meniscus zone using a detailed particle in cell (PIC) model of the ion source in the presence of transverse magnetic field. [ABSTRACT FROM AUTHOR]

To realize stable negative ion beams for 100 s required in the neutral beam injector of JT-60SA, a physical model to control cesium (Cs) distribution inside the negative ion source has been developed in order to maintain the stable negative ion production at the plasma grid (PG) surface with Cs. In this work, to quantitatively evaluate Cs coverage on the PG, a three-dimensional Cs transportation code was introduced to consider the spatial Cs distribution in the source. The spatial temperature distribution of the chamber wall was also introduced in this model. As a result, the reasonable variation of the Cs coverage for 100 s was obtained, compared to that in the initial model. Based on the modified model, the operational temperature of the chamber wall was proposed to be less than 60 °C to suppress the desorption of Cs in the chamber wall and to sustain the stable negative ion production. In addition, it was also suggested that a slightly higher wall temperature before the operation leads to a decrease in the amount of Cs stored at the chamber wall, resulting in suppression of Cs consumption in the ion source. [ABSTRACT FROM AUTHOR]

Long pulse beam extraction with a current density of 120 A/m² for 100 s has been achieved with a newly developed plasma grid (PG) for the JT-60SA negative ion source which is designed to produce high power and long pulse beams with a negative ion current of 130 A/m² (22 A) and a pulse length of 100 s. The PG temperature is regulated by fluorinated fluids in order to keep the high PG temperature for the cesium-seeded negative ion production. The time constant for temperature controllability of the PG was measured to be below 10 s, which was mainly determined by the heat transfer coefficient of the fluorinated fluid. The measured decay time of the negative ion current extracted from the actively temperature-controlled PG was 430 s which was sufficient for the JT-60SA requirement, and much longer than that by inertial-cooling PG of 60 s. Obtained results of the long pulse capability are utilized to design the full size PG for the JT-60SA negative ion source. [ABSTRACT FROM AUTHOR]

The purpose of this study is to calculate atomic (H0) density distribution in JAEA 10 ampere negative ion source. A collisional radiative model is developed for the calculation of the H0 density distribution. The non-equilibrium feature of the electron energy distribution function (EEDF), which mainly determines the H0 production rate, is included by substituting the EEDF calculated from 3D electron transport analysis. In this paper, the H0 production rate, the ionization rate, and the density distribution in the source chamber are calculated. In the region where high energy electrons exist, the H0 production and the ionization are enhanced. The calculated H0 density distribution with-out the effect of the H0 transport is relatively small in the upper region. In the next step, the effect should be taken into account to obtain more realistic H0 distribution. [ABSTRACT FROM AUTHOR]

For the ITER neutral beam system, reasearch and development of a vacuum-insulated MeV accelerator has been carried out at Japan Atomic Energy Research Institute. After a successful 1 MV insulation in vacuum for more than 2 h, H--ion-beam acceleration test is in progress to fulfill the ITER requirement of the current density of 200 A/m2 at 1 MeV, with good beam optics quality of <7 mrad divergence. For such a high-current-density H--ion-beam acceleration, the Kamaboko negative-ion source was operated at high input power, with increased filament number and magnetic filter strength. The optimum perveance was investigated by scanning the extraction and acceleration voltages, together with the beam divergence measurement. As a consequence, H--ion beams of 146 A/m2 (total ion-beam current: 206 mA) were obtained at 836 keV, of which power density is in the “ITER relevant” level. Such high-power-density beams with a divergence as low as 5 mrad were obtained at the optimum perveance corresponding to that of the ITER (200 A/m2 at 1 MeV). [ABSTRACT FROM AUTHOR]

Focuses on development of intense negative ion source producing multimegawatt hydrogen/deuterium negative ion beams. Neutral beam injector in TOKAMAK thermonuclear fusion machines; Long pulse negative ion source; Beam optics.

Spatially non-uniform electron energy distribution function (EEDF) in an arc driven negative ion source (JAEA 10A negative ion source: 10 A NIS) is calculated numerically by a three-dimensional Monte Carlo kinetic model for electrons to understand spatial distribution of plasma production (such as atomic and ionic hydrogen (H0/H+) production) in source chamber. The local EEDFs were directly calculated from electron orbits including electromagnetic effects and elastic/inelastic collision forces. From the EEDF, spatial distributions of H0/H+ production rate were obtained. The results suggest that spatial non-uniformity of H0/H+ productions is enhanced by high energy component of EEDF. [ABSTRACT FROM AUTHOR]

The influence of magnetic filter configuration on the beam uniformity was examined to improve beam uniformity in a large Cs-seeded negative-ion source. By reducing the filter strength of the transverse magnetic field used in a typical negative-ion source, the beam uniformity was largely improved with the improvement of the plasma uniformity while the beam intensity was kept to be nearly constant. However, the coextracted electron current greatly increased. To suppress the coextracted electron current, a tent-shaped magnetic filter was applied together with modifications in the cusp magnets to form a typical multicusp positive-ion source arrangement. The uniformity in longitudinal beam profile was improved with the deviation of local beam intensity within 16% that was nearly equal to the deviation obtained at 50 G cm of the transverse filter strength. In the meantime, the coextracted electron current was kept to be the same as the H- ion current. The present result suggests that the uniformity of H- ion-beam profile is affected by the uniformity of atoms or protons in the source plasma, which are the primary species of negative ions under Cs-seeded surface production. [ABSTRACT FROM AUTHOR]

A spatial uniformity of negative ion production has been studied experimentally in a tandem-type volume negative ion source, where the plasma is divided into two regions by a magnetic filter, i.e., a driver region and an extraction region near the plasma grid (PG). A plasma density profile and the negative ion beam profile were measured. By the Langmuir probe measurement, a strong nonuniformity of the plasma density was observed near the plasma grid when the plasma grid is biased electrically with respect to the anode. By changing the polarity of the bias voltage, the deviation of the plasma density profile changed to the direction of E x B. In the pure hydrogen operation, the extracted beam profile corresponded to the plasma density profile in the extraction region. In the Cs-seeded operation, on the other hand, the uniformity of the beam current density became uniform despite the nonuniformity of the plasma density profile in the extraction region. The uniformity of the negative ions corresponded to the plasma uniformity in the driver region. These results indicate that the negative ions are not produced by positive ions in the extraction region in the Cs-seeded operation. We conclude that the negative ions are produced mainly by neutral atoms produced in the driver region via the surface production on the PG. [ABSTRACT FROM AUTHOR]

Abstract: The origin of the beam non-uniformity, that is one of the key issues in JT-60 negative ion sources, was experimentally examined by measuring correlations between the intensity of the H− ion beam and plasma parameters, such as an electron temperature and plasma density in the JAERI 10 A negative ion source. The ion source was operated without cesium. Although a uniform filter field was applied, the electron temperature near plasma grid (PG) was higher than 1eV in the upper half region of the longitudinal direction, where the spatial beam intensity decreased rapidly. This indicates that the beam non-uniformity is caused by a higher electron temperature than 1eV, namely, by a leakage of the high-energy electrons toward the PG. To investigate the path of high-energy electrons leaking into the PG, a metal plate of 50mm×50mm was placed in the plasma. By placing the plate in a weak magnetic field of <30G leading to a driver region near the upper wall, the electron temperature near the PG was sufficiently reduced to 1eV in the upper half region, where the beam intensity was simultaneously increased. As a result, a 20% gain of the beam current was obtained. Further, the source of the high-energy electrons leaking toward the PG was examined by changing the relative filament position to the upper wall. It is found that the filaments closest to the upper wall, i.e., at 80mm from the upper wall is one of the sources of the high-energy electrons leaking into the PG. [Copyright &y& Elsevier]

• Experimental campaign on MTF carried out in QST lab in Naka, Ibaraki, Japan. • Opera, SLACCAD, COMSOL, EAMCC3D correctly predict beam divergence. • Semi-empirical Opera model with current density asymmetry correctly predicts the beam deflection. • COMSOL and EAMCC3D slightly underestimate heat loads on the grids. It is a widely recognized phenomenon that, in negative ion sources for NBI, the magnetic fields in the source cause an asymmetry of the current density at the meniscus, which affects the beam optics. In order to achieve a more realistic estimation of the negative ion beam optics, the ion current density profile at the beamlet meniscus is sometimes assumed to be non-symmetric with respect to the beamlet axis. The new hypothesis tested in this paper is an empirical law obtained by recent investigations on a similar Kamaboko ion source, which relates this asymmetry to the magnetic field strength at the meniscus and to the power injected in the ion source. For the first time this hypothesis is used to directly and correctly predict the value of the beamlet deflection. The MeV ion source Test Facility (MTF) is a high voltage negative ion beam accelerator dedicated to fusion experiments in QST, Naka, Ibaraki, Japan. MTF can be operated as a three- or five-stage multi-aperture accelerator with a configuration and beam energy comparable to the future ITER NBI. In 2019, experiments were conducted on MTF aiming at accelerating a H- beam with high energy and good optics for a long duration of the beam (around 100 s). These experiments allowed to measure the beamlet divergence and deflection as well as the heat loads due to particle impinging on the accelerator grids, over a wide range of operating parameters. The predictions of several beam simulation codes (Opera, COMSOL, SLACCAD, EAMCC3D) have been compared to the experimental measurements, which allows to obtain a good agreement in terms of beam optics and a fair agreement in terms of heat loads. [ABSTRACT FROM AUTHOR]