Search

The wind profiler radar (WPR) system requires a dual-polarized antenna with multiple low-sidelobe and high-gain beams to facilitate the detection of weak signals reflected by atmospheric turbulence. This paper proposes a dual-polarized continuous transverse stub (CTS) K-band antenna with four reconfigurable beams, which comprises a series-fed CTS array and four 1-to-14 power dividers as line source generators (LSGs) to generate a high-quality quasi-TEM wave. The CTS element incorporates a stepped transition radiation stub design and employs a short cutoff stub on the upper surface of the series-fed parallel plate waveguide (PPW) to achieve optimal impedance matching. The entire antenna is an all-metal structure with remarkably low loss, and low-cost standard fabrication processes are employed for the prototype, which achieves fast reconfigurable four-beam scanning to 15°, with a gain of 31.09 dBi and sidelobe levels below −17.6 dB. Measurement results in an anechoic chamber agree well with simulations, demonstrating the antenna's ease of manufacture, stability, and suitability for wind profile radar applications. [ABSTRACT FROM AUTHOR]

Millimeter‐Wave (mmWave) antennas for 5G communication require wide bandwidth, directional radiation patterns, low‐profile design and multilayer compatibility for module‐level integration. In this paper, we introduce a method of loading shorting pins to a patch antenna to generate extra zero modes. By merging the 2nd zero‐mode, TM01 mode, 3rd zero‐mode, and TM20 mode in the frequency spectrum, a wide bandwidth varying from 23 to 34 GHz and a low‐profile as 0.762 mm can be obtained. Based on this wideband patch antenna, a 4 × 2 antenna array is obtained with the ±40° scanning performance. Theoretical analysis, full‐wave simulations, and experimental performances are presented, validating the effectiveness of this method to achieve a wideband performance in mmWave band. It can be applied to 5G communication systems in mmWave band. [ABSTRACT FROM AUTHOR]

In the 5G communication utilizing millimeter‐wave (mmWave) band, multilayer configuration is popular for mmWave antenna with module‐level integration and high‐density design. However, multilayer construction adds several substrate layers and metallic ground layers to RF signal paths, which induces extra capacitances and inductances to the original antenna, thereby deteriorating impedance matching, and distorting radiation patterns. In this paper, we investigate the influence of multilayer structure on antenna performances, and apply substrate integrated coaxial line (SICL) design to eliminate these interferences from multilayer configuration. Equivalent circuit model of the multilayer configuration with SICL is presented and verified by simulations. A mmWave antenna unit and the 1 × 4 array in multilayer configuration with SICL design are measured. Experiments show that SICL design enables impedance matching and radiation patterns to be maintained without distortions when applying multiple layers to the mmWave antenna, validating this method. It can be applied to 5G mmWave antennas that desire multilayer construction. [ABSTRACT FROM AUTHOR]

Millimeter wave (mmWave) antennas for 5G communication require wide bandwidth, directional radiation patterns, low-profile design and multi-layer compatibility for module-level integration. In this paper, we introduce a method of loading shorting pins to a patch antenna to generate extra zero-modes. By merging the 2nd zero-mode, TM01 mode, 3rd zero-mode and TM20 mode in the frequency spectrum, a wide bandwidth varying from 23 to 34 GHz (relative bandwidth of 38.6%) and with a low-profile of 0.762 mm (0.07λ0, where λ0 is the wavelength at a middle frequency of 28.5 GHz) can be obtained. Based on this wideband patch antenna, a 4 × 2 antenna array is obtained with the ±40° scanning performance. Theoretical analysis, full-wave simulations and experimental performances are presented, validating the effectiveness of this method to achieve a wideband performance in a mmWave band. It can be applied to 5G communication systems using mmWave bands. [ABSTRACT FROM AUTHOR]

A novel fan-out wafer-level packaging (FOWLP) technology with double-sided redistribution layers (RDLs) and tall copper vertical interconnects is described. The design of a dual-polarized magnetoelectric (ME) dipole antenna based on this new packaging technology is presented. It is shown that the antenna with a size of $10\times10$ mm2 achieves good impedance matching and a stable radiation pattern over a wide bandwidth from 25 to 43 GHz, which can cover most of the millimeter-wave (mmWave) bands of the fifth-generation (5G) mobile networks in different countries. The measurement results demonstrate that the antenna is well suited for FOWLP technology and can be used for phased-array modules in 5G wireless communication systems. [ABSTRACT FROM AUTHOR]

In this communication, we report the scanning manipulation on radiation beams with an active metamaterial (MTM) antenna using p-i-n diode switches. Thanks to the MTM antenna possessing periodical configuration with isolated units, p-i-n diodes in each unit are capable of being actuated individually with OFF/ON-states (coding sequences 0/1), equivalently tuning the phase constant $\beta $ of each cell either in state $\beta _{0}$ or state $\beta _{1}$. Therefore, for MTM array with a certain number of units, we can obtain plenty of tunable states presented via digitally coding sequence combinations, thereby manipulating beam scanning in a fixed frequency band. Especially, for the first time, we propose the digitally modulated array factor (DMAF) method for the MTM array: introducing unit-cell dispersion curves of both 0/1 states to the array factor, thus, map the digitally coding sequences linearly to the scanning beams at a fixed frequency, resulting in scanning functionalities. Experiments are implemented with applying micro-control-unit (MCU) to the active MTM antenna for driving p-i-n diodes, and measurements demonstrate beam scanning continuously from −30° to +30° at fixed frequencies around 5 GHz, validating the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a wideband eight‐element antenna array operating in the 5G (Fifth‐generation) NR (New Radio) frequency bands N77/N78/N79 (3300‐5000 MHz), LTE (Long Term Evolution) band 46 (5150‐5925 MHz), and EU (European Union) 5G band of 5900 to 6400 MHz for 8 × 8 MIMO (Multi‐Input Multi‐Output) operation in the future 5G mobile terminal is presented. The proposed eight antenna elements are all co‐coupled‐fed IFA (Inverted‐F antenna)/loop structure, and are divided into two same sub‐arrays which printed on the inner surface of two long frames of the mobile terminal, respectively. All the simulated and measured results present consecutive 6‐dB impedance bandwidth of 3200 to 6500 MHz, acceptable isolations (better than 12 dB), and good total efficiencies (more than 50%). Besides, the proposed wideband 8‐antenna MIMO system has also shown good MIMO performances with ECCs (envelope correlation coefficient) are all lower than 0.08, and ergodic channel capacities are all higher than 37.8 bps/Hz within the entire desired operation bands. In addition, the hand phantom effects are also investigated. The prototype of the proposed wideband eight‐element antenna array is fabricated and measured, and a quite good agreement between simulation and measurement is obtained. [ABSTRACT FROM AUTHOR]

A wideband one-dimensional tightly coupled dipole array (TCDA) with enhanced impedance matching is presented in this letter, which consists of eight printed dipole units, a coplanar waveguide with ground feeding network, and two rows of parasitic strips. The feed structure is simple and small with good ports isolation. A $1\times 8$ prototype was fabricated and tested. A four-channel phase-amplitude control board was designed to validate the beam-steering function of the proposed TCDA. This array has a height of only $0.176\;\lambda_{\text{low}}$ , and it exhibits a measured 10 dB return-loss operating bandwidth of 92.7% from 2.2 to 6.0 GHz for the scan angle up to $\pm 45^{\circ }$ broadside radiation. The cross-polarization suppression level is better than 15 dB in the whole scanning range. The measured results show high gains $>$ 6.9 dBi, high efficiency $>$ 67%, and low sidelobe level (SLL) $<$ $-$ 10 dB over the operating band and scanning angles. This antenna array can be applied in the future massive multiple-input–multiple-output beamforming systems for 5G and other applications. [ABSTRACT FROM AUTHOR]

A dual‐band eight‐antenna array operating in the long‐term evolution (LTE) band 41 (2.496‐2.69 GHz) and 3.5‐GHz band (3.3‐3.7 GHz) for fifth‐generation (5G) metal‐framed smartphone is presented. The proposed dual‐band antenna array is composed of four identical dual‐antenna building blocks (DABBs). Each DABB consists of two identical antenna elements with a neutralization line between them. The antenna array is simulated, fabricated, and measured. The isolations are better than 10.5 dB and 11.0 dB in the low band (LB; LTE band 41) and high band (HB; 3.5‐GHz band). The total efficiencies are 41% to 54% and 46% to 64% in the two operation bands, respectively. In addition, the measured envelope correlation coefficients are less than 0.11 and 0.06, the calculated channel capacities are better than 34.5 and 36.3 bps/Hz in the LB and HB, respectively. Furthermore, four hand‐grip scenarios are investigated, and results show that proposed antenna array can maintain excellent multiple‐input multiple‐output performances in all scenarios. [ABSTRACT FROM AUTHOR]

A 10‐element multiple‐input multiple‐output (MIMO) handset antenna array with triple‐band operation in the long‐term evolution band 42 (3400‐3600 MHz), band 43 (3600‐3800 MHz), and band 46 (5150‐5925 MHz) is studied in this article. Acceptable antenna performances are obtained by using polarization and pattern diversity techniques. To assess the multiplexing performances of the handset array in 5G, an 8‐element base station array covering 3.4‐7.1 GHz is presented and studied. An 8 × 10 MIMO system incorporating 8 transmit antennas, propagation scenario and 10 receive antennas is successfully reported, and its multiplexing performances are evaluated. The computed channel capacities in the low and high bands can be as high as 43.3 bps/Hz and 41.6 bps/Hz, which are promising for multi‐gigabit‐per‐second (multi‐Gbps) data transmission in 5G. The effects of user's hand and low MIMO order on the channel capacities are also investigated. Results show the robust performances of the proposed antenna system. [ABSTRACT FROM AUTHOR]

A dual‐band 8 × 8 antenna array operating in the long term evolution (LTE) band 42 (3400‐3600 MHz) and LTE band 46 (5150‐5925 MHz) for 5G communication multi‐input multi‐output (MIMO) operation in the smartphone is presented. The proposed dual‐band antenna array element is composed of an L‐shaped open slot antenna and a U‐shaped monopole antenna. The measured results exhibited acceptable isolation (better than 12 dB) and good efficiency (more than 50%) across the two desired operation bandwidths. In addition to that, the proposed antenna array has also shown good MIMO performances with envelope correlation coefficient (ECC) lower than 0.1, and ergodic channel capacities higher than 38.8 bps/Hz in the operation bands. The hand phantom effects are also investigated, and the results show that the proposed antenna array can still exhibit good radiation and MIMO performances when operating under the single hand mode (SHM) and dual hands mode (DHM). [ABSTRACT FROM AUTHOR]