Search

The fabrication of new membrane that is able to produce stable high power density is essential for the development of pressure retarded osmosis (PRO) technology. In this work, thin film composite (TFC) polyetherimide membranes with three different substrate structures were fabricated and characterized. The PRO performance of the resultant membrane was evaluated through two pressure cycle experiments and stability tests. The primary objective of this work is to systematically study PRO membrane’s mechanical stability and mass transfer properties under high operating pressures, which determine the power density of the membrane in the PRO process. Experiments revealed that water permeability ( A p ) and salt permeability ( B p ) under different pressures varied. The A p and B p are better indicators for examining the variation of PRO membrane structure under pressure. Within the operating pressure range of 17.2 bar, the top polyamide layer of TFC PEI-2# membrane mainly experienced a reversible deformation. In the two pressure cycle tests, the water flux, specific salt flux and power density obtained in the upward and downward measurements in each cycle are close to each other. The first cycle and the second cycle also show excellent reproducibility. The membrane was able to maintain almost unchanged water flux and power density of 12.8 W/m 2 at 17.2 bar over the 10 h testing time, suggesting the membrane’s great potential to be used in practical application in the future. [ABSTRACT FROM AUTHOR]

Abstract: For the first time, a specially designed pressure retarded osmosis (PRO) hollow fiber membrane has been successfully developed and applied in the PRO process to demonstrate its potential for power generation. The membrane fabrication method is similar to that used for making thin-film composite (TFC) forward osmosis hollow fiber membranes, but further optimization and improvement have led to a new type of TFC hollow fiber membranes with much greater mechanical strength in addition to its excellent separation property and high water flux. The TFC PRO hollow fiber membranes have a water permeability (A) of 9.22×10−12 m/(sPa), salt permeability (B) of 3.86×10−8 m/s and structural parameter (S) of 4.6×10−4 m. It can withstand hydrostatic pressure as high as 9bar with its relatively large dimension of 0.98mm lumen diameter. This PRO hollow fiber membrane is superior to all other PRO membranes reported in the open literature in terms of power density. A power density as high as 10.6W/m2 can be achieved using seawater brine (1.0M NaCl) and wastewater brine (40mM NaCl), which suggests that the newly developed PRO hollow fiber membrane has great potential to be applied in PRO processes to harvest salinity gradient energy. A higher pressure is preferred as it allows generation of higher power density (pressures of 12bar may be optimal for seawater as the high salinity stream), and this can be realized by reduced fiber dimension. Further optimization of the membrane structure will be performed. [Copyright &y& Elsevier]

Abstract: Forward osmosis (FO) has received intensive studies recently for a range of potential applications such as wastewater treatment, water purification and seawater desalination. One of the major challenges to be overcome is the lack of an optimized FO membrane that can produce a high water flux comparable to commercial RO membranes. Two types of thin-film composite FO hollow fibers with an ultra-thin polyamide-based RO-like skin layer (300–600nm) on either the outer surface (#A-FO) or inner surface (#B-FO) of a porous hollow fiber substrate have been successfully fabricated. These novel composite FO hollow fibers have been characterized by a series of standard protocols and benchmarked against commercially available FO flat sheet membranes and reported NF hollow fibers used for the FO process. The characterization reveals that the FO hollow fiber membranes possess a large lumen. The substrates are highly porous with a narrow pore size distribution. The active layers present excellent intrinsic separation properties with a hydrophilic rejection layer and good mechanical strength. The #B-FO hollow fiber membrane can achieve a high FO water flux of 32.2L/m2 h using a 0.5M NaCl draw solution in the active rejection layer facing draw solution (AL-facing-DS) configuration at 23°C. The corresponding salt flux is only 3.7g/m2 h. To the best of our knowledge, the performance of the #B-FO hollow fiber is superior to all FO membranes reported in the open literature. The current study suggests that the optimal FO membrane structure would possess a very small portion of sponge-like layer in a thin and highly porous substrate, which suggests a way for further improvement. [Copyright &y& Elsevier]

Abstract: There has been a resurgence of interest in forward osmosis (FO) as a potential means of desalination, dewatering and in pressure retarded osmosis, which Sidney Loeb was advocating over 3decades ago. This paper describes the characteristics and potential applications of a newly developed FO hollow fiber membrane, which was fabricated by interfacial polymerization on the inner surface of a polyethersulfone (PES) hollow fiber. This FO membrane presents excellent intrinsic separation properties, with a water flux of 42.6L/m2 h using 0.5M NaCl as the draw solution and DI water as the feed with the active layer facing the draw solution orientation at 23°C. The corresponding ratio of salt flux to water flux was only 0.094g/L, which is superior to all other FO membranes reported in the open literature. To evaluate different application scenarios, various NaCl solutions (500ppm (8.6mM), 1wt.% (0.17M) and 3.5wt.% (0.59M)) were used as the feed water to test the performance of the FO membrane. The membrane can achieve a water flux of 12.4L/m2 h with 3.5wt.% NaCl solution as the feed and 2M NaCl as the draw solution, suggesting it has good potential for seawater desalination. [ABSTRACT FROM AUTHOR]