Search

Real-time satellite clock offset is a crucial element for real-time precise point positioning (RT-PPP). However, the elapsed time for undifferenced (UD) multi-global navigation satellite system (GNSS) real-time satellite clock offset estimation at each epoch is increased with the growth of stations, which may fall short of real-time application requirements. Therefore, a rapid estimation method for UD multi-GNSS real-time satellite clock offset is proposed to improve the computation efficiency, in which both the dimension of the normal equation (NEQ) and the number of redundant observations are calculated before adjustment; if these two values are larger than the predefined thresholds, the elevation mask is gradually increased until they are less than the predefined thresholds. Then, the clock offset estimation is conducted; this method is called clock offset estimation using partial observations. Totals of 50, 60, 70 and 80 stations are applied to perform experiments. Compared to clock offset estimation using all observations, the elapsed times of clock offset estimation using partial observations can be reduced from 6.80 to 3.10 s, 7.93 to 2.97 s, 12.04 to 3.14 s for 60, 70 and 80 stations, respectively. By using the proposed method, the elapsed time of the clock offset estimation at each epoch is less than 5 s. The estimated clock offset accuracy for GPS, BDS-3, Galileo and GLONASS satellites are better than 0.04, 0.05, 0.03 and 0.16 ns when using the partial observations to estimate clock offset with 50, 60, 70 and 80 stations, respectively. For the multi-GNSS kinematic PPP using the estimated clock offset from 50, 60, 70 and 80 stations with partial observations, the positioning accuracy at 95% confidence level in the east, north and up direction are better than 2.70, 2.20 and 5.60 cm, respectively. [ABSTRACT FROM AUTHOR]

The quality of real-time satellite clock offsets products is one of the key elements for real-time satellite clock performance monitoring and real-time precise point positioning (PPP). However, impacted by the station location, environment, communication equipment, receiver performance, network delay, temporary modem failure or other reasons, the observation data of clock offset datum receiver occasionally outage, resulting in all satellite clocks offset cannot be estimated. In this contribution, an efficient clock offset datum switching compensation method for BDS real-time satellite clock offset estimation is proposed. One hundred stations distributed around the world, from day of year (DOY) 074 to 075 in 2019 are used to estimate BDS real-time satellite clock offset. Four schemes: clock offset datum switching without compensation (S1), clock offset datum switching with satellite clock offset jump compensation (S2), clock offset datum switching with satellite clock offset jump and receiver clock drift compensation (S3, the proposed method), clock offset datum without switching (S4), are used to validate the proposed method. By using the proposed method, the satellite clock offset jump can be eliminated and the satellite clock offset consistency can be maintained. The satellite clock offsets STD for S1, S2, S3 and S4 are 0.184, 0.183, 0.183 and 0.150 ns, respectively. The fitting precision of S1, S2, S3 and S4 are 70907.344, 0.731, 0.502 and 0.543 ns, respectively. The frequency stability of S3 shows the best performance among S2, S3 and S4 when the averaging interval time is 10,000 and 20,000 s, which can be attributed to the effectiveness of proposed method and frequency stability difference of clock offset datum receiver. The fitting precision and frequency stability cannot be reflected correctly by clock offset due to the satellite clock offset jump in S1. For precise point positioning (PPP), the coordinates jump and re-convergence can be eliminated by using the proposed method. Thus, this method can provide a reference for obtaining real-time, continuous and reliable BDS satellite clock offset products. [ABSTRACT FROM AUTHOR]

Abstract The on-orbit characteristics and service performance of Galileo navigation system (Galileo) has been drawn attentions since Galileo is the only one global navigation system which is normally equipped with large-scale, high precision and performance hydrogen atomic clocks. Based on a period of 1000 days' Galileo satellite clock offset products, this article analyzed the performance changes of Galileo satellite clocks when the working clock is switched to the backup clock. The onboard clock phases, frequencies, frequency drifts, the polynomial fitting residuals and the stabilities have been obtained. Results show that the frequency drifts of Galileo satellite clocks can reach up to a magnitude of 10−19 and the fitting precisions are superior to 0.3 ns, while the stabilities in the time length of ten thousand seconds can achieve 10−14. These mainly can be due to the onboard high performance and precision hydrogen atomic clocks. [ABSTRACT FROM AUTHOR]

Abstract Transmission link disturbances and device failure cause global navigation satellite system (GNSS) receivers to miss observations, leading to poor accuracy in real-time kinematic (RTK) positioning. Previously described solutions for this problem are influenced by the length of the prediction period, or are unable to account for changes in receiver state because they use information from previous epochs to make predictions. We propose an algorithm for predicting double difference (DD) observations of obstructed BeiDou navigation system (BDS) GEO satellites. Our approach adopts the first-degree polynomial function for predicting missing observations. We introduce a Douglas-Peucker algorithm to judge the state of the rover receiver to reduce the impact of predictive biases. Static and kinematic experiments were carried out on BDS observations to evaluate the proposed algorithm. The results of our navigation experiment demonstrate that RTK positioning accuracy is improved from meter to decimeter level with fixed ambiguity (horizontal < 2 cm, vertical < 18 cm). Horizontal accuracy is improved by over 50%, and the vertical accuracies of the results of the static and kinematic experiments are increased by 47% and 27% respectively, compared with the results produced by the classical approach. Though as the baseline becomes longer, the accuracy is weakened, our predictive algorithm is an improvement over existing approaches to overcome the issue of missing data. [ABSTRACT FROM AUTHOR]

Abstract The information of the satellite clock switching and performance variations on-orbit of Chinese BeiDou-2 Navigation System (BDS) is not available for the public. In order to detect the BDS satellite clock switching and performances variation, we analyzed the precise clock offset products with a total duration of 5 years every BDS satellite equipped four atomic clocks from four different manufactures from January 2013 to October 2017. Three important contributions are concluded as follows. (1) It is found that the average time of on-orbit operation for BDS satellite clocks is about 1–2 years. There have been 22 times of clock switching for BDS satellites, of which the C05 and C08 satellites have been switched to the fourth (last) atomic clock. (2) There are frequent phase adjustments for BDS on-orbit satellite clocks, and the frequency series is relatively stable. Furthermore, there are semi-annual sinusoid cycles in the frequency drift series of C06 and C09 satellites. (3) The performances of MEO satellite clocks perform better than the IGSO and GEO satellite clocks. The average ten-thousand frequency stability of BDS satellite clocks is about 1E-13, which is worse than that of GPS and Galileo but better than that of GLONASS. [ABSTRACT FROM AUTHOR]

Currently, resolution of the BeiDou2 satellites differential code bias (DCB) is greatly limited by the number of tracking stations and data quality. To improve the precision of calculated DCBs, an adaptive control method, based on elevation angle weight and posteriori variance factor, is proposed. The feasibility and precision of the proposed method are verified via analysis of the DCBs precision and application of single‐frequency precise point positioning (SF‐PPP). The results show that the long‐term variation of the daily BeiDou2 satellite DCB sequence is stable and the precision of DCBs of BeiDou2 satellites in different constellations is different. In addition, it is found by using periodogram and fast Fourier transform (FFT) methods that weekly and daily periodic signals exist in the daily BeiDou2 satellite DCB products. The results of SF‐PPP show that root mean square (RMS) horizontal residual is reduced by 10% and convergence time is shortened significantly using DCB products. © 2018 Institute of Navigation [ABSTRACT FROM AUTHOR]

In the Global Navigation Satellite System (GNSS) community, the Quasi-Zenith Satellite System (QZSS) is an augmentation system for users in the Asia-Pacific region. However, the characteristics and performance of four QZSS satellite clocks in a long-term scale are unknown at present. However, it is crucial to the positioning, navigation and timing (PNT) services of users, especially in Asia-Pacific region. In this study, the characteristics and performance variation of four QZSS satellite clocks, which including the phase, frequency, frequency drift, fitting residuals, frequency accuracy, periodic terms, frequency stability and short-term clock prediction, are revealed in detail for the first time based on the precise satellite clock offset products of nearly 1000 days. The important contributions are as follows: (1) It is detected that the times of phase and frequency jump are 2.25 and 1.5 for every QZSS satellite clock in one year. The magnitude of the frequency drift is about 10−18. The periodic oscillation of frequency drift of J01 and J02 satellite clocks is found. The clock offset model precision of QZSS is 0.33 ns. (2) The two main periods of QZSS satellite clock are 24 and 12 hours, which is the influence of the satellite orbit; (3) The frequency stability of 100, 1000 and 10,000 s are 1.98 × 10−13, 6.59 × 10−14 and 5.39 × 10−14 for QZSS satellite clock, respectively. The visible "bump" is found at about 400 s for J02 and J03 satellite clocks. The short-term clock prediction accuracy of is 0.12 ns. This study provides a reference for the state monitoring and performance variation of the QZSS satellite clock. [ABSTRACT FROM AUTHOR]

In order to provide better service for the Asia-Pacific region, the BeiDou navigation satellite system (BDS) is designed as a constellation containing medium earth orbit (MEO), geostationary earth orbit (GEO), and inclined geosynchronous orbit (IGSO). However, the multi-orbit configuration brings great challenges for orbit determination. When orbit maneuvering, the orbital elements of the maneuvered satellites from broadcast ephemeris are unusable for several hours, which makes it difficult to estimate the initial orbit in the process of precise orbit determination. In addition, the maneuvered force information is unknown, which brings systematic orbit integral errors. In order to avoid these errors, observation data are removed from the iterative adjustment. For the above reasons, the precise orbit products of maneuvered satellites are missing from IGS (international GNSS (Global Navigation Satellite System) service) and iGMAS (international GNSS monitoring and assessment system). This study proposes a method to determine the precise orbits of maneuvered satellites for BeiDou GEO and IGSO. The initial orbits of maneuvered satellites could be backward forecasted according to the precise orbit products. The systematic errors caused by unmodeled maneuvered force are absorbed by estimated pseudo-stochastic pulses. The proposed method for determining the precise orbits of maneuvered satellites is validated by analyzing data of stations from the Multi-GNSS Experiment (MGEX). The results show that the precise orbits of maneuvered satellites can be estimated correctly when orbit maneuvering, which could supplement the precise products from the analysis centers of IGS and iGMAS. It can significantly improve the integrality and continuity of the precise products and subsequently provide better precise products for users. [ABSTRACT FROM AUTHOR]