Search

Steering knuckles are vital functional and structural components in automotive suspension systems, requiring high strength, high ductility, and complex shapes. In this study, an aluminum alloy knuckle with the semi-solid die casting process was developed to replace the conventional steel components. This research aims to optimize product design based on both structural simulation and casting process simulation to avoid defects and to meet mechanical requirements. Furthermore, the optimal design solutions need to be verified through the filling experiments and defect analysis. The results show that the removal of support rib located in the thick area of the shock absorber mounting arm is helpful to avoid the rewelding defects in the filling frontier of the SSM melt. Besides, the position of the steering rod is of medium thickness, and two ribs from different directions come together to support that area. Rewelding defects were detected when two ribs come together. To avoid rewelding defects in local areas of steering rod position, the ribs were reduced to uniform wall thickness. Thus, the local flow state was modified and the SSM melt was reinforced shear action. Ultimately, by controlling all the processes of the SSM die casting process, the high performance of aluminum knuckle was successfully developed.

The flow behavior of semi-solid slurry determines the quality of the castings produced by the semi-solid forming process. Many studies have done to investigate the flow behavior of slurry under different conditions, and results show that the rheological behavior of slurry with dendritic structure is inappropriate for semi-solid forming. In this study, slurries with varying morphologies of grain for the same alloy with the same fraction solid have tested using a partial filling method. The SEED process was employed, and the pouring temperature adjusted to prepare semi-solid slurries with different grain morphologies. The flow pattern, entrapped air during the filling process, and also microstructure of the samples were examined to characterize the macro and micro flow behavior. The results show that a turbulent macro-flow, leading to entrapped air, and severe segregation appeared in the sample using slurry of Tpour ≥ 660 °C . For the slurry of Tpour < 660 °C, none of the three phenomena found in the sample. This investigation further showed that the detriment of dendrite on the semi-solid forming process, and implied that large size dendrite in semi-solid slurry must avoided.

The Rheo-diecast process has been rapidly developed and increasingly used in China in the recent 5 years. The high solid fraction (solid content close to 50%) rheo-diecast components were commercially used in the transportation markets mainly because of lightweight. The mechanical properties of the high solid fraction rheo-diecast components are obviously superior than that of the conventional liquid diecast parts. The defects such as oxide, gas entrapment, shrinkage porosities are well prevented in the high solid fraction rheo-diecast parts. The high solid fraction rheo-diecast parts can be fully T6 heat treated. A comparison between high solid fraction rheo-diecast part and conventional liquid diecast part will be described in detail. The low solid fraction (solid content 5-20%) rheo-diecast components were widely used in the 5G communication markets. The future perspectives of Rheo-diecast process will be described at last. 1. Cost reduction. 2. Production consistency. 3. New Rheo-diecast alloys development. 4. Numerical simulation of Rheological filling.

Controlling the morphology of the microstructure of the slurry is important during semi-solid die casting. For this project, semi-solid slugs were produced using the SEED (Swirled Enthalpy Equilibrium Device) process, where a fully liquid metal is poured into a steel crucible and cooled into the semi-solid temperature range, and the crucible and slurry are then swirled and cooled to the appropriate temperature (and solid fraction) for semi-solid casting. The pouring temperature of the melt into the crucible during SEED processing has been shown to influence the morphology and size of the aluminum solid particles within the slurry, which can influence the distribution and segregation of the solid particles during die casting. In this study, a specially-designed die with a serpentine-shaped flow channel has been used to study the distribution of the solid particles during semi-solid die casting. The experimental results show that a dendritic structure is formed when the liquid is poured from a high temperature, while a globular semi-solid morphology is more easily formed when poured from a low superheat. The current results also show that a dendritic structure leads to severe segregation during die casting.

There are two new processes to development automobile structural components which have certain thickness. In the present paper, taking a main bearing cap product as an example, analyses die design by comparing the experimental and computational numerical simulation results. For the main bearing cap, product structure and mold design were designed to be suitable for characters of SSM die casting and squeeze process. Semi-solid slurry has significantly higher viscosity than liquid metal. This character of fluidity and solid fraction phase make the flow condition more laminar than liquid squeeze casting with the partial fill experiment. And compared with squeeze casting process, the globular shape grain size is smaller than dendritic structure. And mechanical property result shows that the elongation of SSM die casting can achieve more than twice than squeeze casting.

Recent developments and applications of rheo-diecast components for transportation markets are described. The components have been produced using the SEED (Swirled Enthalpy Equilibrium Device) semi-solid process. The development process typically involves several steps, including (1) an evaluation (and modification) of the component design to ensure it is suitable for semi-solid die casting, (2) the use of flow and solidification simulation to optimize the layout of the gating system, and to ensure that the modified component design can be produced without filling turbulence and shrinkage porosity, (3) stress modeling to ensure that the redesigned component will meet performance targets, and (4) in-plant development of the optimum process parameters. This development process will be described in detail for several commercial components, including two brackets for trucking applications, and connectors used in the frame of an electric bus.

Semi-solid aluminum slurries have globular grains, different from traditional dendritic solidification microstructures. The mechanism responsible for the formation of these globular grains is still in dispute. Some researchers suggest that the globular grains are formed by fractured dendrites, while others report it is due to copious nucleation. This study will model the growth of the α-Al phase during the production of semi-solid slurries using the swirled equilibrium enthalpy device (SEED) process, where liquid alloy with a low superheat is poured into a steel crucible and swirled within the semi-solid region. Experimental observations have shown that the final microstructure of the slurry produced by the SEED process is relatively non-uniform, with large dendrites at surface and fine spherical particles at the center. Open source code for the phase field method has been adopted to simulate the different microstructural evolution for semi-solid alloy 357.0. The effect of localized temperatures under isothermal condition on the morphology of the α-Al particles has been investigated according to the special conditions of the SEED process. In addition, suggestions for modifying the slurry production to achieve more uniform microstructure are discussed.

A201 alloy is the strongest cast aluminum alloy, but it is considered one of the most difficult aluminum alloys to cast due to its susceptibility to hot tearing during solidification. Semi-solid casting, which characterizes fine near-globular or non-dendritic grains and relatively narrow solidification range, is potential to reduce hot cracking tendency of alloys. In this present work, semi-solid slurries of A201 alloy were prepared using Swirled Enthalpy Equilibrium Device (SEED) technique and then injected into a self-designed high pressure hot tearing mold. The microstructures of A201 semi-solid slurries with different pouring temperatures were examined. Effects of different casting pressures on the hot tearing sensitivity of A201 have been investigated. This study finds that SEED is capable of producing satisfying A201 semi-solid slurries. Lower pouring temperatures produce A201 semi-solid slurries with finer and rounder grains as well as more uniform microstructure distribution. Increasing the intensification pressure significantly decreases the hot treating tendency of A201 alloy. When the pressure reaches to 90 MPa and the mold temperature of about 250 °C, the hot tearing susceptibility (HTS) index value is nearly zero, which means almost no surface cracks are found in the semi-solid A201 die casting parts.

Microstructures with fine globular grains and refined eutectic structures are important to enhance the mechanical properties of A356 alloys processed by semi-solid and gravity die casting. Rare earth (RE) additions have been shown to be capable of refining both the α-Al particles as well as modify the eutectic phase of alloys. In semi-solid die casting, Al7Si0.3Mg alloys with RE concentrations (0, 0.1 and 0.4 wt.%) were used to prepare semi-solid slurries using the SEED (Swirling Enthalpy Equilibrium Device) method, and subsequently semi-solid die cast. The same compositions of alloys were also applied to gravity die casting. The microstructure and mechanical properties of castings in two processes have been characterized. Compared to the grains produced in gravity die casting, globular grains with small size (260 μm) in the semi-solid die casting significantly enhance the UTS and elongation of alloys. Although the size of grains had no change with increasing RE concentrations in alloys. The Al-Si eutectics were changed to refined morphology with the 0.1 wt.% RE addition, which enhanced the ductility of alloys in two processes. When increasing the RE addition to 0.4 wt.%, the RE-rich phases precipitated at grain boundaries, which decreased the UTS and elongation of alloys.

The commercial application of wrought aluminum alloys to semi-solid casting would be extremely beneficial, as wrought alloys often exhibit better strength-ductility combinations than cast aluminum alloys. Semi-solid casting typically reduces the hot tearing tendency, as it requires a globular microstructure and produces grain refinement, but hot tearing often still occurs during the semi-solid die casting of complex-shaped components produced from wrought alloys. This study examined the impact of intensification pressure and grain refinement on the hot tearing tendency of an Al-Zn-Mg-Cu alloy. Semi-solid slurries were produced using the SEED (Swirled Equilibrium Enthalpy Device) process. A specially designed constrained rod mold was used to evaluate hot tearing. Results showed the tendency for hot tearing decreased with increasing of intensification pressure. Grain refinement (with 0.06Ti) was also found to be beneficial to the elimination of hot tearing.

The semi-solid casting process has a lot of advantages in controlling casting defects. High quality impellers have been produced successfully by the semi-solid process for several years. The semi-solid processed impellers have uniform microstructure and premier mechanical properties, and therefore excellent durability. Further improvement of performance of the impellers is demanded and achieved by increasing curvature and length of blades of impellers. These changes create potential trend of casting defects in blades of impellers, such as non-filling holes. In our recently work, castings were made in different conditions, including two-step plunger velocity and one-step plunger velocity. The experimental results show that the change of plunger velocity played a decisive role in the forming of non-filling holes. Entrapped gas is the direct reason of the non-filling holes. With the increasing of plunger velocity, the area of non-filling holes increased. The non-filling holes in blades could be avoided by eliminating the plunger velocity’s changing during filling blades.

A crucial problem concerned with the semi-solid forming process is the liquid segregation phenomena during shape formation, especially for rheo-casting process. Liquid segregation occurs due to the separation phenomena of the solid grain and the liquid phase. In this work, using commercial finite element software, the liquid segregation during rheo-casting process was numerically investigated by Eulerian-granular multiphase model based on the comparable results of single phase model, Eulerian-granular two-phase and three-phase model, along with Eulerian-granular DDPM three-phase model. In the study, solid grains and liquid phases were regarded as rigid material and non-Newtonian fluid at microscale, separately. This validation was experimentally proved and also compared to the proposed relationship of power law, Herschel-Bulkley model with yield stress at macroscale.

Semi-solid slurry has significantly higher viscosity than liquid metal. This character of fluidity makes product design and die design, such as gating system, overflow and venting system, be different between these two die casting processes. In the present paper, taking a clamp product as an example, analyses the product optimization and die design by comparing the experimental and computational numerical simulation results. For the clamp, product structure is designed to be suitable for characters of SSM die casting process. The gating system is designed to be uniform variation of thickness, making the cross-sectional area uniformly reduce from the biscuit to the gate. This design ensures semi-solid metal slurry to fill die cavity from thick wall to thin wall. Gate position is designed at the thickest location, the gate shape of semi-solid die casting is set to be much bigger than traditional liquid casting. A good filling behaviour can be achieved by aforementioned all these design principles and it will be helpful to the intensification of pressure feeding after filling.

Surface blistering during T6 heat treating is an artifact that is essentially unique to high pressure casting processes such as semi-solid casting and die casting. It is believed that the blistering originates from subsurface defects present in the castings. When the castings are exposed to elevated temperatures during solution heat treatment, the strength of the aluminum is reduced, and the defects expand to deform the surfaces of the castings. There are three potential sources for the subsurface defects - entrapped air, die lubricant or shot sleeve lubricant.This paper will report on a study to determine the origin of the defects present in the castings that produce the blisters. Along with attempting to separate the influence of air and the two types of lubricants on blister formation, the study will also examine the impact of a number of process parameters on blistering.

T6 heat treatment is an effective method to improve the comprehensive properties of Al-Si-Cu-Mg series aluminium alloys. Solution treatment temperature and time, quench process and media, as well as artificial ageing temperature and time are the key factors to determine mechanical properties. Besides these factors, natural ageing, i.e. the holding time between quenching and the starting of artificial treatment at ambient temperature was observed to be significant affect mechanical properties of the aluminium alloys. This effect on semi solid processed aluminium alloys was lack of investigations as the semi solid process produces T6 treatable and weldable components. The present paper focuses on the change regularity of hardness and precipitate behaviour of semi-solid 319S aluminium alloy under different natural ageing (NA) treatment additional to standard T6. Density and morphology of hardening precipitates are analysed using TEM, and the influence mechanism of NA during T6 heat treatment will be discussed. The results show that NA has a positive influence on mechanical properties of the rheo-cast 319S alloy.

The enthalpy equilibration method is a novel technique to produce globular grain structure in semi-solid slurry preparation. In this process, the liquid is firstly poured into a metallic crucible, which possesses low thermal conductivity and high thermal capacity. Homogeneous distribution of temperature within the metallic crucible is achieved by rotating the crucible and cold down to a temperature between liquidus and solidus, determined by the requirement of solid fraction. The semi-solid slurry is then transferred to a high pressure die caster. In order to achieve a spherical microstructure morphologies in the entire slurry, effects of grain refiners, in addition to the enthalpy equilibration method, on the microstructure of the slurries of A357 alloy were investigated. Quantitative metallographic measurements were applied to evaluate microstructural evolution and processing parameters were optimized.

The spheroidal grains in billets used for semi-solid casting are generally manufactured by electromagnetic stirring (EMS) during the casting process. This method however, is not economically applicable for small quantities of the thixo billets. Swirled Enthalpy Equilibration Device (SEED) has been developed as a rheocasting process, and the SEED process is of interest for developing new thixo alloys, as well as for optimizing the thixocasting processes for high quality components. The objective of this paper is to compare the microstructure and mechanical properties of aluminum alloy 319s billets and castings produced using EMS and SEED feed materials. The experimental results show that for as-cast billets made from SEED process, a well-developed spheroidal grain structure is distributed throughout the cross-section of the billet, while for as-cast EMS billets, the grain structure is inhomogeneous, i.e., a dendritic structure was present adjacent to the surface of the billet, while a uniform, spheroidal structure was present at the centre. After the thixocasting process, however, the both SEED and EMS billets have well-developed, spheroidal grain structures. Mechanical properties of thixocast and T61 heat treated components are comparable for the both SEED and EMS billets.

A general rule in conventional liquid metal casting processes is that smaller size would produce better metallurgical quality and mechanical properties. The conclusion that semi-solid thixocasting process doesnt follow this rule has been made recently. The microstructure and mechanical properties of semi-solid thixocastings are much less dependent on casting size and cooling rate than the liquid castings. The step casting in the previous study is specially designed and simplified. The practical castings, e.g. turbocharger impellers, are more complex than the step castings. In this work, the turbocharger impeller is used to study the impact of section size representing the casting size on the microstructure and mechanical properties of semi-solid thixocastings, compared with the step casting. Section thickness decreases from 50 mm to 3.5 mm. In addition, the impact of casting thickness on the eutectic phase is also presented. The results reveal that the size of primary α-Al particles is insensitive to the casting thickness in semi-solid thixocasting. The cooling rate has a notable impact on the size and geometric characteristics of the eutectic silicon particles, but the impact is reduced by the following T61 heat treatment. The association between the casting thickness and casting defects is discussed, in order to further understand the impact of casting size on durability and reliability of real casting components.

Turbocharger impellers undergo extreme cyclic speed conditions and thus fatigue fracture in service. Any kind of defects, even defects with sizes of tens of micrometres, can make significant impact on service life of the impellers. The alloy used for thixocast impellers is the aluminum alloy 319s. T61 heat treatment is used to improve mechanical properties. However, the solution treatment in the standard T61 heat treatment of the 319s alloy can induce incipient melting defects. This paper carried out systematic study of formation of defects caused by the incipient melting during solution treatment in the thixocast and heat treated impellers, using optical and scanning electron microscope. Based on the study, the critical temperature of incipient melting is detected. An optimized two-stage solution treatment is therefore proposed.

The thixocasting technology is chosen to produce the turbocharger impellers as it is capable of producing castings with high precision dimension, free of oxide and shrinkage porosity defects and therefore long service life. The thixocasting turbocharger impellers have the similar mechanical property to those produced by forging and machine processes, but much less costs. In the thixocasting process, the semisolid slurry with certain solid fraction is injected into mould at a high speed. Since high viscosity and thixotropic characteristics, the semisolid slurry reveals unique flow condition and characteristics in the filling process. So, its very desirable for the die design, process optimization, and defect control to visualize the high-speed filling process of semisolid slurry by numerical simulation. In this paper, several commonly used viscosity models for semisolid slurry are analysed. The Power law cut-off model (PLCO) model is selected to simulate the filling process in the thixocasting process of the impellers of 319s alloy, compared with actual results by partial filling testing. The causes of the casting defects are also analysed, indicating that the simulation results can accurately reproduce the filling process of semisolid slurry, and PLCO model is a successful choice for simulating the filling process of semisolid slurry with high solid fraction.