Search

The viability of arbuscular mycorrhizal fungi (AMF) spores formulated with biochars derived from the pyrolysis of raw (ROP) or impregnated olive pomace with olive mill wastewaters (IROP) was investigated under laboratory-controlled conditions. A greenhouse experiment was also conducted to study the effect of AMF spores and biochars adding on the growth of maize plants. Nine treatments, combining one biochar (ROP or IROP) at a level of 2.5 g/kg of soil and inoculation or not with Funneliformis mosseae at two concentrations (30 and 125 spores/kg of soil), were arranged in an entirely randomized block design. The results of the formulation trial showed that arbuscular mycorrhizal fungi (AMF) spores had short-term viability and are sensitive to the presence of biochar. This effect is more pronounced when the biochar is made from IROP. Both the AMF and biochars treatments did not significantly enhance the growth of maize plants, biomass production, and leaf chlorophyll contents. However, the most significant effect on nutrients uptake was observed in the modalities treated with AMF alone (30 spores/kg of soil) and AMF combined with the biochar made from IROP (IROP $+$ 30 spores/kg of soil). In those modalities, the N uptake was improved by 45% and 33%, respectively. Moreover, biochar addition to the soil did not particularly enhance root colonization by AMF and no negative effect of its application was observed either. However, the inoculation of spores enhanced propagules production and maize root colonization.

This paper presents an in-depth characterization of a raw industrial sludge (IS-R) and its KOH-activated biochar pyrolyzed at 750 °C (IS-KOH-B) followed by their application to remove a cationic dye from aqueous solution. Materials characterization shows that compared to the IS-R, the IS-KOH-B has improved structural, textural, and surface chemical properties. In particular, the IS-KOH-B's BET surface area and total pore volume are about 78 and 6 times higher than those found for the IS-R, respectively. The activated biochar efficiently retained the cationic dye under wide experimental conditions. Indeed, for an initial dye concentration of 50 mg L−1, removal yields were assessed to be more than 92.5%, 93.5%, and 97.8% for a large pH range (4–10), in the presence of high contents of competing cations (3000 mg L−1 of Ca2+, Mg2+, Na+, and K+), and a low used adsorbent dose (1 g L−1), respectively. The Langmuir's adsorption capacities were 48.5 and 65.9 mg g−1 for of IS-R and IS-KOH-B, respectively, which are higher than those reported for various adsorbents in the literature. The dye removal was found to be monolayer, spontaneous, and endothermic for both the adsorbents. Moreover, this removal process seems to be controlled by chemical reactions for IS-KOH-B whereas by both physico–chemical reactions for IS-R. This study demonstrates that the raw industrial sludge and especially its KOH-activated derived biochar could be considered as promising adsorbents for the removal of dyes from aqueous solutions. [ABSTRACT FROM AUTHOR]

This study investigates—for the first time—the synthesis of a novel Ca-rich biochar (N–Ca–B) and its potential use for phosphorus (P) recovery from both synthetic solutions (SS) and treated urban wastewater (TUW) in a continuous stirring tank reactor (CSTR) mode. The novel biochar was synthesized by pyrolysis at 900 °C of a mixture composed of three different materials: animal biomass (poultry manure; PM), lignocellulosic waste (date palm fronds; DPFs), and abundant mineral waste (waste marble powder; WMP). Characterization of N–Ca–B showed that it has good textural properties: well-developed porosity, and high specific surface area. Furthermore, high calcium hydroxide (Ca(OH) 2) and calcium oxides (CaO) nanoparticle loads were observed on the biochar surface. The dynamic CSTR assays indicated that the P recovery efficiency mainly depended on the biochar mass, P influent concentration, and, especially, the Ca content of the feeding solution. Owing to its richness in Ca cations, TUW exhibited the highest adsorbed P amount (109.2 mg g−1), i.e., about 14% larger than the SS. P recovery occurs through precipitation as hydroxyapatite, surface complexation, and electrostatic interactions with positively charged biochar particles. In real-world scenarios, CSTR systems can be applied as a tertiary treatment step in existing wastewater treatment plants (WWTPs). Decanted P-loaded biochar can be used in agriculture as a slow-release fertilizer instead of commercial products. [Display omitted] • Waste marble powder used for calcium-rich biochar synthesis. • Ca-rich biochar has interesting physico-chemical properties. • Ca-rich biochar efficiently recovers phosphorus in CSTR mode. • Ca-rich biochar recovers high phosphorus amounts from wastewater. • Proposed approach promotes sustainability and circular economy. [ABSTRACT FROM AUTHOR]

Phosphorus (P) represents a major pollutant of water resources and at the same time a vital element for human and plants. P recovery from wastewaters and its reuse is a necessity in order to compensate the current important depletion of P natural reserves. The use of biochars for P recovery from wastewaters and their subsequent valorization in agriculture, instead of synthetic industrial fertilizers, promotes circular economy and sustainability concepts. However, P retention by pristine biochars is usually low and a modification step is always required to improve their P recovery efficiency. The pre- or post-treatment of biochars with metal salts seems to be one of the most efficient approaches. This review aims to summarize and discuss the most recent developments (from 2020- up to now) in: i) the role of the feedstock nature, the metal salt type, the pyrolysis conditions, and the experimental adsorption parameters on metallic-nanoparticles-loaded biochars properties and effectiveness in recovering P from aqueous solutions, as well as the dominant involved mechanisms, ii) the effect of the eluent solutions nature on the regeneration ability of P-loaded biochars, and iii) the practical challenges facing the upscaling of P-loaded biochars production and valorization in agriculture. This review shows that the synthesized biochars through slow pyrolysis at relatively high temperatures (up to 700–800 °C) of mixed biomasses with Ca– Mg-rich materials or impregnated biomasses with specific metals in order to from layered double hydroxides (LDHs) biochars composites exhibit interesting structural, textural and surface chemistry properties allowing high P recovery efficiency. Depending on the pyrolysis's and adsorption's experimental conditions, these modified biochars may recover P through combined mechanisms including mainly electrostatic attraction, ligand exchange, surface complexation, hydrogen bonding, and precipitation. Moreover, the P-loaded biochars can be used directly in agriculture or efficiently regenerated with alkaline solutions. Finally, this review emphasizes the challenges concerning the production and use of P-loaded biochars in a context of circular economy. They concern the optimization of P recovery process from wastewater in real-time scenarios, the reduction of energy-related biochars production costs and the intensification of communication/dissemination campaigns to all the concerned actors (i.e., farmers, consumers, stakeholders, and policymakers) on the benefits of P-loaded biochars reuse. We believe that this review is beneficial for new breakthroughs on the synthesis and green application of metallic-nanoparticles-loaded biochars. [Display omitted] • Biochars usually have low phosphorus contents limiting their use in agriculture. • Raw biochars exhibit low phosphorus adsorption yields. • Loading biochars with nanomaterials improve their P recovery capacities. • Mixing biomasses with Ca– Mg-rich materials is an interesting option. • Biochars decoration with LDHs permits high P recovery efficiency. [ABSTRACT FROM AUTHOR]

Lead removal from aqueous solutions by raw cypress ( Cupressus sempervirens L.) sawdust (RCS) and its derivative magnesium pretreated biochar (Mg-B) was investigated under static and dynamic conditions through batch and column assays. The Hydrus-1D model was used to estimate the transport parameters of the lead measured breakthrough curves. The batch experiments results showed that Mg-B was very efficient in removing lead compared to RCS and several other previously tested natural and modified materials. The column experiments results indicated that for both RCS and Mg-B, lead breakthrough curves and the related removal efficiencies were mainly dependent on the used initial concentration and the adsorbents bed height. The use of Hydrus-1D showed that the two-site chemical non-equilibrium model describes better the experimental lead breakthrough curves for both RCS and Mg-B as the equilibrium model. [ABSTRACT FROM AUTHOR]

During the last decade, biochars have been considered as attractive and eco-friendly materials with various applications including wastewater treatment, energy production and soil amendments. However, the important nitrogen losses during biochars production using the pyrolysis process have limited their potential use in agriculture as biofertilizer. Therefore, it seems necessary to enrich these biochars with nitrogen sources before their use in agricultural soils. This paper is the first comprehensive review on the assessment of biomass type and the biochars' properties effects on N recovery efficiency from aqueous solutions as well as its release and availability for plants when applying the N-enriched chars in soils. In particular, the N recovery efficiency by raw biochars versus the type of the raw feedstock is summarized. Then, correlations between the adsorption performance and the main physico-chemical properties are established. The main mechanisms involved during ammonium (NH 4 –N) and nitrates (NO 3 –N) recovery process are thoroughly discussed. A special attention is given to the assessment of the biochars physico-chemical modification impact on their N recovery capacities improvement. After that, the application of these N-enriched biochars in agriculture and their impacts on plants growth as well as methane and nitrous oxide greenhouse gas emissions reduction are also discussed. Finally, the main future development and challenges of biochars enrichment with N from wastewaters and their valorization as biofertilizers for plants growth and greenhouse gas (GHG) emissions reduction are provided. This systematic review is intended to promote the real application of biochars for nutrients recovery from wastewaters and their reuse as eco-friendly fertilizers. [Display omitted] • Biochars have low nitrogen contents which limit their use in agriculture. • Biochars hybrid modifications allow high recovery yields of ammonium and nitrates. • N-laden biochars promote the seedling stage and the vegetative growth. • N-enriched biochars significantly reduce the N 2 O and CH 4 emissions. • N-enriched biochars promote sustainability and circular economy concepts. [ABSTRACT FROM AUTHOR]

This work examines in silico the dominant geochemical processes that control inorganic nutrients (Ca, Mg, Na, K) availability in irrigated agricultural soil amended with potassium-enriched biochar (from olive mill wastes) at mass doses of 0.5%, 1%, 2% and 10%. The geochemical modelling step was supported by analytical measurements regarding the physicochemical characteristics of the irrigation water, the agricultural soil and the biochar. Two geochemical approaches, namely equilibrium exchange (E.E.) and kinetic exchange (K.E.) models were applied and compared to assess nutrient release with an emphasis on potassium availability. Equilibrium exchange perspective assumed that nutrient release is controlled by ion-exchange reactions onto the biochar surface, whilst kinetic exchange perspective assumed the contribution of both ion-exchange and dissolution of salts. Results indicated that for the E.E. model, the soluble amount of potassium is readily available for transport within the pores of the porous media, and therefore is leached from the column within only 10 days. For the K.E. model that assumes a kinetically controlled release of potassium due to interactions occurring at the solid-solution interface, the assessed retention times were more realistic and significantly higher (up to 100 days). Concerning the applied doses of biochar, for a 2% biochar fraction mixed with soil, for example, the available K for plants doubled compared with the available K in the soil without biochar. In any case, the use of numerical modeling was proven helpful for a quick assessment of biochar performance in soil, by avoiding time-consuming and laborious experimental set-ups. Validation of the models by experimental data will further establish the proposed mechanisms. [ABSTRACT FROM AUTHOR]

Pyrolysis is a thermochemical process that permits the conversion of biomasses into energy (bio-oil and biogas) and a solid residue called biochar. The generation of biochar from lignocellulosic materials has been, for longtime, the predominant research focus. Wastewater treatment plants produce huge amounts of sludge biomass and there exists an increasing evidence for their possible reuse as a promising pyrolysis feedstock in recent literature. Though the valorization of biochars generated from lignocellulosic biomasses has been the subject of many reviews, there exists a critical knowledge gap regarding the effect of synthesis conditions of the sludge-derived biochars (SDBs) on their efficiency in the treatment of wastewater. This review critically analyzes the available literature related to SDBs characteristics and application to adsorb inorganic and organic pollutants from effluents. The physico-chemical properties and adsorption efficiency of SDBs are mainly tuned by the nature of raw sludge, pyrolysis conditions, and pre/post-treatments. Indeed, biochars originating from digested sludge have better adsorption capacities towards nutrients and heavy metals compared to those obtained from the non-digested sludge. The nutrients recovery from urban wastewater could be significantly improved when the raw sludge is mixed with lignocellulosic biomass and Mg/Ca rich materials. On the other hand, the chemical activation of sludge at reagent/sludge ratios higher than 2:1 permits to generate SDBs with adsorption capacities comparable and even better than commercial activated carbons. Moreover, the embedment/coating of SDBs with specific nanomaterials and tailored functional groups could significantly improve the adsorption capacities of various organic toxic pollutants and at the same time enhance their chemical degradation. The effect of the nature of target pollutants (organic or inorganic) on the underlying adsorption mechanisms by SDBs was also deeply reviewed. Finally, this paper provides the main application challenges as well as insights regarding the promising future directions for SDBs research and development. • This review evaluates the use of sludge-derived biochars for wastewater treatment. • Synthesis conditions influence the adsorption properties of SDBs. • Higher removal capacities of pollutants are obtained with activated SDBs. • Significant increases of removal capacities with nanocomposite-embedded SDBs. • Adsorption mechanisms are different for organic and inorganic pollutants. [ABSTRACT FROM AUTHOR]

Olive mill wastes continue to be a management challenge due to the large volumes produced, particularly due to their toxicity and impacts on the environment. Thermal conversion through pyrolysis or hydrothermal carbonization techniques can detoxify wastes while conserving nutrient contents. In this work, we produced up-to-date data on olive mill waste flows in Spain, Tunisia, and Greece and characterized representative samples in the laboratory. Assays of thermal conversion of olive mill wastewaters and solid wastes were also performed to understand biochar yields and final properties, and the total quantities of nutrients contained were estimated. Of particular note were the quantities of potassium in Tunisian wastewaters, representing 0.6% of the total mass and an annual flow of approximately 5000 t, and in the Spanish solid wastes, an average of 1.7% of the total mass is potassium, representing an annual flow of approximately 23,000 t. Concerning phosphorus, Spanish solid wastes had the highest contents (0.1%), double that of other countries' wastes. Annually, olive mill wastes from the three countries are estimated to contain approximately 35 × 103 tons of potassium and 2.6 × 103 tons of phosphorus. With this resource converted to biochar, each year more than 700 km2 of soils could be enriched in 0.2% carbon with biochar at an application rate of 7 t ha−1. [ABSTRACT FROM AUTHOR]

Raw poultry manure (RPM) and its derived biochars at temperatures of 400 (B400) and 600 °C (B600) were physico-chemically characterized, and their ability to release nutrients was assessed under static conditions. The experimental results showed that RPM pyrolysis operation significantly affects its morphology, surface charges, and area, as well as its functional groups contents, which in turn influences its nutrient release ability. The batch experiments indicated that nutrient release from the RPM as well as biochars attains a pseudo-equilibrium state after a contact time of about 48 h. RPM pyrolysis increased phosphorus stability in residual biochars and, in contrast, transformed potassium to a more leachable form. For instance, at this contact time, P- and K-released amounts passed from 5.1 and 25.6 mg g−1 for RPM to only 3.8 and more than 43.3 mg g−1 for B400, respectively. On the other hand, six successive leaching batch experiments with a duration of 48 h each showed that P and K release from the produced biochars was a very slow process since negligible amounts continued to be released even after a total duration of 12 days. All these results suggest that RPM-derived biochars have specific physico-chemical characteristics allowing them to be used in agriculture as low-cost and slow-release fertilizers. [ABSTRACT FROM AUTHOR]

In this study, lead removal from aqueous solutions using biochar derived from olive mill solid and liquid wastes has been investigated by applying batch experiments and geochemical modelling. The batch adsorption experiments included the assessment of several key parameters such as the contact time (kinetic), initial concentration (isotherm), pH, adsorbent dose, and the presence of competitive cations, whilst the geochemical modelling focused on the involved adsorption mechanisms using the PHREEQC code. The kinetic studies showed that lead adsorption is a relatively fast process, where intraparticle diffusion is the rate-limiting step. Biochar dose, solution pH and the presence of competitive ions significantly affected the Pb adsorption effectiveness by the biochar. Especially the higher Pb removal percentages were observed in mono-elemental solutions with high biochar dose at mildly acidic solution pH values. The maximum Pb adsorption capacity of biochar was estimated as 40.8 mg g−1 which is higher than various biochars derived from sludge, lignocellulosic and animal biomasses. On the other hand, the geochemical modelling employing the PHREEQC code showed that ion exchange and Pb precipitation are the main reactions controlling its removal from aqueous solutions, whilst surface complexation is insignificant, mainly due to the low surface functional groups on the used biochar. • Utilise olive mill solid waste (OMSW) biochar to remove Pb from aqueous solutions. • Batch sorption experiments described by Elovich kinetic equation and Sips isotherm model. • Modelling sorption process using the PHREEQC code. • Ion-exchange and precipitation were found as the key retention mechanisms of Pb. • OMSW biochar can be applied as a cost-effective and environmentally friendly sorbent. [ABSTRACT FROM AUTHOR]

The olive oil industry is an important economic sector in Mediterranean countries. However, oil production is unfortunately accompanied by the generation of huge amounts of olive mill solid wastes (OMSW) and olive mill wastewater (OMWW). In the present study, a strategy is proposed for converting these olive mill wastes into biochar through pyrolysis, for their later use as an organic amendment in agriculture. Specifically, two biochars were prepared from the pyrolysis of OMSW at 500 °C, either alone or impregnated with OMWW (OMSW-B and I-OMSW-B). The characterization of the OMSW and I-OMSW samples and their derived biochars showed that the fixed carbon and ash contents in the feedstocks increased by 38% and 11% respectively for OMSW-B, and by 37% and 12% respectively for I-OMSW-B. Interestingly, the impregnation process significantly increased Na, P, K, Ca and Fe contents in the produced biochars. The effect of OMSW-B and I-OMSW-B amendments at different application dose (1%, 2.5% and 5% wt/wt) on the enzymatic activity of an agricultural soil was performed at laboratory scale with a pot test. The experimental results showed that phosphatase and urease activity increased with biochar application rate; amendment with I-OMSW-B at 1%, 2.5% and 5% enhanced the phosphatase activity by 63%, 142% and 285% and urease activity by 50%, 116% and 149%, respectively. On the other hand, dehydrogenase and protease activities were higher for the application rate of 2.5% biochar. Biochar amendment promoted tomatoes seedling growth after 10 weeks, which was highest in the application rates of 2.5% and 5% for both OMSW-B and I-OSMW-B. Thus, the produced biochars had great potential to be used as biofertilizers in agriculture. Unlabelled Image • Slow pyrolysis performed to convert OMSW and its impregnated form onto biochars • Biochars characterized using proximate, mineral analysis and crystalline structure • I-OMSW-B exhibited high contents of C, P and K comparing to initial feedstocks. • I-OMSW-B amendment promoted tomatoes seedling growth and enzymatic activities. • Studied biochars didn't have phytotoxic effect under tested doses. [ABSTRACT FROM AUTHOR]

Olive mill wastewater (OMW) is nowadays considered as a serious source pollution. At the same time, it contains high amounts of nutrients, especially potassium and phosphorus that could be recovered for agricultural purposes. The aim of the current experimental research work is to investigate the agronomic potential use of OMW based biochar produced from the slow pyrolysis at 500 °C of raw cypress sawdust (CS) impregnated with OMW (ICS-OMW-B). In order to understand the contribution of OMW, two additional biochars were produced from raw cypress sawdust (RCS-B) and cypress sawdust pretreated with potassium chloride (ICS-K-B). Results indicated that RCS impregnation by OMW significantly improved the produced biochar's chemical properties, especially its nutrients contents. Furthermore, in comparison with the other biochars, ICS-OMW-B application as an organic fertilizer showed promising results in terms of produced fresh and dry masses, as well as potassium bioavailability as assessed in test experiments with ryegrass. For instance, the dry matter masses of the rye-grass treated with ICS-OMW-B were about 23, 34 and 50 wt% higher than the ones measured for the tests using RCS-B, ICS-K-B and synthetic K-fertilizer as amendments, respectively. Besides, this biochar has a potential effect on the suppression of various pathogens existing in the tested agricultural soil. All these results demonstrated that the biochar generated from the slow pyrolysis of impregnated sawdust with OMW could be considered as attractive and promising organic fertilizer for acidic agricultural soils. Unlabelled Image • Cypress sawdust impregnated with olive mill wastewater was used to elaborate biochars. • The fertilizing potential of the biochars was evaluated through ryegrass growth tests. • Biochar enriched with olive mill wastewater is an efficient organic fertilizer. • The effect of biochar on soil aggregate stability and pathogen growth was assessed. • K and P bioavailabilities were estimated through the analyses of rye grass leaves. [ABSTRACT FROM AUTHOR]

• Raw kenaf stems and its pyrolytic char are fully characterized. • Thermal properties of kenaf stems are more interesting than many other usual crops. • Kenaf stem derived char is very promising for pollutants removal or gas storage. • Kenaf derived char is suitable for soil amendments. • High SSA of the 500 °C-chars incite to activation process to get excellent AC. Kenaf stems are characterized in this present investigation in order to assess their suitability in energy recovery through a pyrolysis process and to identify sustainable applications of the generated biochar. In particular, the raw biomass properties are analyzed using numerous analytical techniques such as thermogravimetric analyses (TGA/DTG), X-Ray Fluorescence (XRF) and Scanning Electronic Microscopy (SEM). First, the thermogravimetric analyses monitor the pyrolysis parameters, control the proportion of its outputs and allow to extract the kinetic parameters. The latter is determined using Friedman, Flynn-Wall-Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS) models. In a second step, Kenaf derived chars are produced at different pyrolysis temperatures and their physicochemical, morphological, textural and structural properties are determined using different techniques such as CO 2 adsorption, Raman Spectroscopy, and DRIFT Spectroscopy. The main results confirm the Kenaf potential for energy applications as its thermal properties are more interesting compared to other usual crops. The Kenaf stem derived char is also very promising for pollutants removal or gas storage as its surface area as well as its microporous structure are interestingly developed when increasing the pyrolysis temperature. Kenaf char could be also chemically or physically activated in order to be used for pollutants removal from gaseous and aqueous effluents. Finally, the XRF analysis indicated that contents in K and P elements are high. Ca and Mg are also major mineral species in the char. These contents indicate that Kenaf derived char could be also suitable for agricultural soil amendments. [ABSTRACT FROM AUTHOR]